Search the part. Verify the offer.

STM32F103C8T6 is a mainstream Arm Cortex-M3 microcontroller from STMicroelectronics with 64 KB Flash in a 48-pin LQFP package — one of the most widely designed-in 32-bit MCUs for embedded control, motor control and industrial I/O. Its advantage for procurement is ecosystem depth: toolchains, reference designs and engineer familiarity are all mature, which shortens development and second-source risk. Selection advice: the C8 density code (64 KB) is the critical match point — firmware and memory layout are qualified against a specific density, so ordering the wrong density variant risks incompatibility; the full ordering code must match your BOM character-for-character, not just the STM32F103 base name. T6 denotes the LQFP-48 package. This is also one of the most counterfeited MCU part numbers in the open market: always require lot and date-code traceability, and confirm the exact ordering code, package and documentation requirements in your RFQ — we reply within 24 hours.

STM32F407VGT6 is a high-performance Arm Cortex-M4 microcontroller from STMicroelectronics in a 100-pin LQFP package, with DSP instructions and a floating-point unit. The Cortex-M4 with FPU is the selection point over Cortex-M3 parts: signal processing, motor-control math and floating-point algorithms run far faster, which is why this part anchors industrial control, audio processing and IoT gateways. Selection advice: the VG code denotes this Flash density and the T6 the LQFP-100 package — match the full code, since the STM32F4 family spans many densities and packages. Verify your peripheral and pinout requirements against the datasheet; high-pin-count MCUs are not drop-in interchangeable across the family. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

STM32G030F6P6 is an entry-level Arm Cortex-M0+ microcontroller from STMicroelectronics in a 20-pin TSSOP package — for compact control designs that need 32-bit performance at an 8-bit budget. The Cortex-M0+ at this price point is the selection point: it undercuts older 8-bit designs on cost while giving modern debug and toolchain support. Selection advice: the F6P6 code denotes the Flash size and TSSOP-20 package — match the full code, since the STM32G0 family spans multiple densities and packages. Confirm your peripheral and pin-count needs against the datasheet. This family is heavily counterfeited: require lot and date-code traceability. State quantity, packing and traceability requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

STM32L072CBT6 is an ultra-low-power Arm Cortex-M0+ microcontroller from STMicroelectronics in a 48-pin LQFP package — for battery-powered and energy-harvesting connected products. The ultra-low-power design is the selection point: sleep currents in the microamp range that stretch coin-cell life to years, which is the whole point of this family. Selection advice: the CBT6 code denotes the Flash size and LQFP-48 package — match the full code to your layout. For LoRaWAN and similar LPWAN designs this is a common host MCU; confirm your radio interface and peripheral needs against the datasheet. Require lot and date-code traceability against counterfeit stock. State quantity, packing and traceability requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ATMEGA328P-AU is an 8-bit AVR microcontroller from Microchip Technology in a 32-pin TQFP package — for embedded control and instrumentation. This is the chip behind the Arduino Uno: the largest hobbyist and educational ecosystem of any microcontroller, which means code examples and libraries for nearly every sensor. Selection advice: the AU suffix denotes TQFP-32 — the ATMEGA328P also ships in PDIP-28 (PU suffix), so match the full ATMEGA328P-AU code to your layout. The P (picoPower) variant is the low-power pick over the non-P version. Confirm your Flash and peripheral needs against the datasheet. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ATMEGA2560-16AU is a high-pin-count 8-bit AVR microcontroller from Microchip Technology with 256 KB Flash in a 100-pin TQFP package — for I/O-heavy embedded control. The 256 KB Flash with 100-pin I/O is the selection point: the largest AVR 8-bit device, the chip behind the Arduino Mega, for designs that outgrew smaller AVRs but want to stay in the 8-bit ecosystem. Selection advice: the 16AU suffix denotes the 16 MHz speed grade in TQFP-100 — match the full code to your layout and clock requirements. If your firmware fits in 128 KB, the ATMEGA1280 is the cheaper drop-in alternative in the same package. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ATTINY85-20SU is a compact 8-bit AVR microcontroller from Microchip Technology in an 8-pin SOIC package — for small embedded functions like LED control, button handling and simple sensor interfaces. Five usable I/O pins in an 8-pin package is the selection point: the smallest practical microcontroller for glue-logic replacement and tiny control tasks. Selection advice: the 20SU suffix denotes the 20 MHz speed grade in SOIC-8 — the ATTINY85 also ships in PDIP-8, so match the full ATTINY85-20SU code to your layout. For new tiny designs, compare against newer ATTiny 0/1-series parts on peripherals; for existing builds, match the code exactly. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

PIC16F877A-I/PT is an 8-bit PIC microcontroller from Microchip Technology in a 44-pin TQFP package, with integrated analog and serial peripherals — for embedded control, instrumentation and education. This is the classic teaching PIC: decades of textbooks, examples and programmer support make it the default for PIC-based learning and legacy industrial designs. Selection advice: the I/PT suffix denotes the industrial temperature grade in TQFP-44 — the PIC16F877A also ships in PDIP-40, so match the full PIC16F877A-I/PT code to your layout. For new designs, compare against newer PIC16F1xxx parts on peripherals and price; for existing builds and coursework, match the code exactly. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

PIC18F4550-I/PT is an 8-bit PIC18 microcontroller from Microchip Technology in a 44-pin TQFP package, with full-speed USB connectivity — for USB device designs, data acquisition and human-interface devices. The integrated USB 2.0 device peripheral is the selection point: native USB without an external bridge chip, which is why this part anchored countless DIY and industrial USB projects. Selection advice: the I/PT suffix denotes the industrial temperature grade in TQFP-44 — match the full PIC18F4550-I/PT code to your layout. Confirm your USB class and driver needs against the datasheet, and note the 5 V-tolerant I/O for mixed-voltage designs. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ATSAMD21G18A-AU is a Microchip SAM D21 Arm Cortex-M0+ microcontroller in TQFP-48 — for low-power embedded control, USB devices and capacitive-touch interfaces. The G18A variant carries 256 KB Flash and 32 KB SRAM, runs at up to 48 MHz from 1.62 to 3.63 V, and the AU code breaks down as A = TQFP package with U = −40 to +85 °C package grade with matte Sn plating, supplied in tray. Selection advice: if your board uses the QFN-48 footprint, order ATSAMD21G18A-MU instead — it is not pin-compatible with this TQFP part — and choose the -AF grade only if you need the −40 to +125 °C rating. Ordering codes verified against the Microchip SAM D21 datasheet DS40001882, Ordering Information and Table 3-4. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM358DR is a dual general-purpose operational amplifier from Texas Instruments in an 8-pin SOIC package — for signal conditioning, active filters and comparator-with-hysteresis circuits. The single-supply operation down to 3 V is the selection point: it runs directly from the same rail as 3.3 V and 5 V logic, which is why the LM358 remains the default jelly-bean op-amp. Selection advice: the DR suffix denotes SOIC-8 on tape and reel — the LM358 ships in PDIP-8 and other packages, so match the full LM358DR code to your footprint. For new precision designs, compare against newer low-offset op-amps; for cost-driven general-purpose use, this is the part. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

NE555DR is the industry-standard 555 precision timer from Texas Instruments in an 8-pin SOIC package, for oscillation, delay and pulse-generation circuits. Its advantage is ubiquity: the 555 architecture has been in continuous production for decades, so designs, application notes and engineer familiarity are universal — but that ubiquity is also the procurement risk, because the open market carries remarked and substandard copies. Selection advice: DR denotes SOIC-8 on tape and reel; always quote the full NE555DR code and require lot and date-code traceability rather than accepting loose or unmarked stock. For new designs, confirm whether your circuit needs the bipolar NE555 or the CMOS LMC555 variant — they are not interchangeable in all applications. State quantity, packing and traceability requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TL072CDR is a dual low-noise JFET-input operational amplifier from Texas Instruments in an 8-pin SOIC package, for analog signal paths — audio preamps, active filters and sensor buffers. The JFET input stage is the selection-relevant advantage: very high input impedance and low input bias current, which suits high-impedance sources that would be loaded down by bipolar-input amplifiers. Selection advice: the CDR suffix denotes the commercial-grade SOIC-8 on tape and reel — the TL07x family spans single, dual and quad variants across grades and packages, so match the full TL072CDR code. For new low-noise designs, also evaluate current-production JFET or CMOS alternatives against your noise and bandwidth budget before committing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

OPA2134UA is a dual low-distortion operational amplifier from Texas Instruments in an 8-pin SOIC package — for precision audio designs, preamplifiers and active crossovers. The FET input with very low distortion is the selection point: it replaced the NE5532 in high-end audio where input bias current and distortion matter. Selection advice: the UA suffix denotes SOIC-8 — the OPA2134 also ships in PDIP-8 (PA suffix), so match the full OPA2134UA code to your footprint. Confirm your supply voltage and distortion requirements against the datasheet before substituting for the NE5532. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP6002-I/SN is a dual low-power rail-to-rail operational amplifier from Microchip Technology in an 8-pin SOIC package — for sensor interfaces and battery-powered signal chains. The rail-to-rail input/output on a 1.8 V to 6 V supply is the selection point: full signal swing from a single low-voltage rail, which is exactly what 3.3 V sensor nodes need. Selection advice: the I/SN suffix denotes the industrial temperature grade in SOIC-8 — the MCP6002 ships in multiple packages, so match the full MCP6002-I/SN code to your footprint. Confirm your gain-bandwidth and offset requirements against the datasheet; this is a low-power part, not a precision part. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620ARZ is an Analog Devices low-power instrumentation amplifier (A grade) in 8-pin SOIC — gain set from 1 to 10,000 with a single external resistor, for bridge sensors, strain gauges and other small differential signals. The single-resistor gain setting is the selection point: a classic three-op-amp instrumentation topology in one package with high common-mode rejection and minimal external circuitry, which shortens precision front-end design. Selection advice: ARZ is the standard A grade in SOIC-8, tube packing — the reel versions are AD620ARZ-REEL (13-inch reel) and AD620ARZ-REEL7 (7-inch reel), so match the full code to your footprint, accuracy grade and line format. For tighter offset — 50 µV max at 25 °C with VS = ±5 V to ±15 V (85 µV max over temperature) — choose the B-grade AD620BRZ-R7. Gain is set by one resistor value, so confirm your gain calculation against the datasheet formula during design. Evidence: ADI AD620 datasheet Rev. H specifications (Table 2) and the ADI AD620 Part Models page (lists ARZ, ARZ-REEL7, BRZ-R7 and BRZ-RL orderables). State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8606ARZ is a dual rail-to-rail precision operational amplifier from Analog Devices in an 8-pin SOIC package — for low-voltage precision systems, data acquisition front ends and medical instrumentation. The combination of precision DC specs with rail-to-rail operation is the selection point: it brings precision-grade offset and drift to single-supply low-voltage designs that older precision op-amps cannot serve. Selection advice: the ARZ suffix denotes SOIC-8 on tape and reel — match the full AD8606ARZ code to your footprint and packing needs. Confirm your offset, drift and noise requirements against the datasheet before substituting for a general-purpose op-amp. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX31855KASA+T is an Analog Devices (Maxim) cold-junction-compensated K-type thermocouple-to-digital converter in 8-pin SOIC, tape and reel — for industrial temperature sensing: HVAC, appliances and process monitoring. 14-bit conversion with 0.25 °C resolution and integrated cold-junction compensation is the selection point: direct thermocouple-to-digital in one chip, no calibration tables. Selection advice: the K in KASA+T denotes K-type (-200 °C to +1350 °C range); sibling variants cover J, N, T, S, R and E types — match the letter to your thermocouple, they are not interchangeable; the read-only SPI interface suits simple MCU polling; note it is designed for ungrounded thermocouples. 3.0 V to 3.6 V supply. ADI lists this part as Active. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS3232MZ+TRL is a temperature-compensated real-time clock with integrated memory from Analog Devices (Maxim Integrated) in an 8-pin SOIC package. Temperature compensation is the key advantage: the RTC holds its accuracy across temperature swings without external crystal trimming, which removes a calibration step from production and keeps timekeeping reliable in outdoor and industrial equipment. Selection advice: the + denotes the lead-free/RoHS configuration and TRL tape-and-reel packing — both must match your assembly and compliance requirements, so quote the full DS3232MZ+TRL code rather than the base DS3232. If your design needs battery backup, state your backup-power and date-code requirements in the RFQ; we reconfirm the offered lot, packing and traceability before quotation and reply within 24 hours.

INA219AIDCNR is a Texas Instruments zero-drift bidirectional current and power monitor in SOT-23-8, tape and reel — for power telemetry: servers, telecom and test equipment. Reporting bus voltage, shunt current and computed power over I2C is the selection point: full power telemetry from one chip plus a shunt resistor. Selection advice: the DCNR suffix denotes SOT-23-8 in 3000-piece tape and reel — for the SOIC-8 package, the INA219AIDR is the sibling; the A grade versus the higher-accuracy B grade — pick B only if your error budget needs it; the 0 V to 26 V bus range covers most DC rails. 3 V to 5.5 V supply. TI lists this part as ACTIVE. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TPS5430DDAR is a 3 A step-down switching regulator from Texas Instruments in an 8-pin SO PowerPAD package, for distributed power architectures — point-of-load rails derived from a higher-voltage bus. Its advantage over linear regulation is efficiency: at 3 A output, a switcher wastes far less power as heat, which shrinks heatsinking and improves system reliability. Selection advice: the DDA suffix denotes the thermally enhanced PowerPAD package and R tape-and-reel packing — thermal performance depends on the PowerPAD soldered to copper, so follow the datasheet layout guidance. Switching regulators need their inductor and compensation network designed around the chip; confirm your input/output voltage and current requirements against the datasheet before substituting a different regulator. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM2596S-ADJ/NOPB is a Texas Instruments SIMPLE SWITCHER 3 A step-down regulator in TO-263-5 (DDPAK), tube — for general-purpose buck conversion: appliances, industrial power and pre-regulation. 3 A switching with only a handful of external components is the selection point: the classic easy-to-design buck. Selection advice: the S suffix denotes the TO-263 surface-mount package — for through-hole, the TO-220 LM2596T variants are the siblings; ADJ is the adjustable 1.2 V to 37 V version — for fixed 3.3 V, 5 V or 12 V rails, the fixed versions need no feedback divider; the 150 kHz switching keeps design simple but needs a larger inductor than modern MHz bucks — pick it for simplicity and proven supply, not for smallest size. 4.5 V to 40 V input. TI lists this part as ACTIVE. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TPS62160DSGR is a Texas Instruments DCS-Control synchronous step-down converter in 2 x 2 mm WSON-8, tape and reel — for high-density power rails: battery systems and 12 V intermediate rails. 2.25 MHz switching with 17 µA quiescent current is the selection point: tiny inductors plus high light-load efficiency. Selection advice: the DSGR suffix denotes the 2 x 2 mm WSON-8 package — for the 3 x 3 mm VSSOP-8, the DGK variants are the siblings; TI documents pin-to-pin compatibility with the TPS62170 and TPS62125 — verify against the datasheet before substituting; the adjustable 0.9 V to 6 V version suits non-standard rails, fixed versions exist for standard rails. 3 V to 17 V input, up to 1 A output. TI lists this part as ACTIVE. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TPS7A4901DGNR is a Texas Instruments 36 V, 150 mA ultra-low-noise positive linear regulator in MSOP-8 PowerPAD, tape and reel — for clean analog rails: op amps, ADCs, DACs and precision instrumentation. 12.7 µVRMS noise with 72 dB PSRR is the selection point: post-DC/DC ripple filtering for noise-sensitive circuits. Selection advice: the DGNR suffix denotes MSOP-8 PowerPAD in tape and reel — the adjustable 1.194 V to 33 V version; the negative-rail complement is the TPS7A3001 — for bipolar analog supplies, pair them; the enable pin plus capacitor-programmable soft start suit sequenced rails. 3 V to 36 V input. TI lists this part as ACTIVE. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.