AD8422BRZ

AD620ARZ is a low-power instrumentation amplifier from Analog Devices in an 8-pin SOIC package, with gain set by a single external resistor — for bridge sensors, strain gauges and other small differential signals. Its advantage is the classic three-op-amp instrumentation topology in one package: high common-mode rejection with minimal external circuitry, which shortens precision front-end design. Selection advice: the ARZ suffix denotes the standard grade in SOIC-8 on tape and reel — the AD620 also ships in DIP and higher grades, so match the full code to your footprint and accuracy requirements. Gain is set by one resistor value, so confirm your gain calculation against the datasheet formula during design. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620BRZ-R7 is an Analog Devices instrumentation amplifier in 8-lead SOIC_N, 7-inch tape and reel — gain set from 1 to 10,000 with a single external resistor, ±2.3 V to ±18 V dual supply (4.6 V to 36 V single), 15 µV maximum input offset (B grade), 1 MHz bandwidth, 1.3 mA maximum supply current, rated −40 °C to +85 °C. The single-resistor gain setting is the selection point: bridge sensors, thermocouples and strain gauges get a precision differential front end with one resistor instead of a matched-resistor op-amp network that drifts with temperature and layout. Selection advice: BRZ is the B grade (tighter offset than the A-grade AD620ARZ-R7), R-8 the SOIC package, R7 the 7-inch reel — the AD620BRZ-RL is the identical die on a 13-inch reel if your line prefers larger reels. DigiKey lists this code Active. Evidence: the ADI AD620 datasheet Rev. H ordering guide confirms the ordering code, B grade, 7-inch reel and −40 to +85 °C rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD623ARZ-R7 is an Analog Devices single-supply instrumentation amplifier, rail-to-rail output, gain 1 to 1000 set by one external resistor, 800 kHz bandwidth at G=1, in SOIC-8 — the sensor front-end amplifier for bridges, thermocouples and low-level transducer signals. The single-resistor gain programming is the selection point: no matched resistor networks to source, with 0.10% gain accuracy at G=1, 200 µV max offset and 550 µA max supply current for battery-powered instruments. Selection advice: it runs on 3 to 12 V single supply or ±2.5 to ±6 V dual supply — but note the input range extends only 150 mV below ground on a single rail, so ground-referenced bipolar sensor signals still need the dual-supply configuration. The R7 suffix is the 7-inch reel (1000 pcs) packing of the SOIC-8. For higher precision or lower noise, compare the AD620/AD8221 family rather than assuming drop-in equivalence. Parameters verified against the ADI AD623 datasheet and Mouser/LCSC listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AMC1350DWVR is a Texas Instruments isolated amplifier in 8-pin SOIC — for precision voltage sensing across isolation barriers: reinforced isolation with ±5V input range, optimized for AC voltage measurement in motor drives, solar inverters and power supplies where the high-voltage side must be galvanically separated from the control side. The DWVR code is the SOIC-8 reel variant with 1000-unit reel. Selection advice: the AMC1350 targets AC voltage sensing (±5V input) — for DC shunt-based current sensing the AMC1301 family is the companion choice; for designs needing an integrated DC/DC converter to power the high side, the AMC3330 eliminates the external isolated supply. Against non-isolated precision amps on this site, the isolation barrier is the differentiator — do not substitute a non-isolated amp where safety isolation is required. Heat evidence: listed in Octopart Linear ICs Popular Parts (octopart.com, verified 2026-10-09); TI E2E forum shows active customer evaluation for high-voltage measurement. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AMC3336QDWERQ1 is a Texas Instruments precision reinforced-isolated delta-sigma modulator — for isolated voltage sensing in automotive and industrial systems: ±1V input range optimized for high-impedance voltage measurements, 1GΩ input resistance, 4250Vrms isolation for 1 minute (UL1577), 6000Vpeak reinforced isolation (DIN VDE V 0884-11), 1200Vrms working voltage, 90kV/µs common-mode transient immunity, 84dB SNR, 21Msps sample rate, integrated DC/DC converter for single-supply operation, AEC-Q100 qualified, 16-pin SO-MOD package, -40°C to 125°C. The integrated isolated DC/DC converter lets the high side run from a single low-side supply, so isolated measurement channels need no separate isolated power — cutting BOM and layout complexity. Business impact: reinforced isolation ratings are a gating item for EV and industrial safety designs — a qualified, stocked part shortens safety certification cycles. Selection advice: the DWER code is the SO-MOD-16 package — for the industrial-grade variant consider the AMC3336; verify creepage and clearance against the reinforced-isolation requirements in the TI datasheet. Featured on hqbuy.com hot search (2026-09-28). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8606ARZ is a dual rail-to-rail precision operational amplifier from Analog Devices in an 8-pin SOIC package — for low-voltage precision systems, data acquisition front ends and medical instrumentation. The combination of precision DC specs with rail-to-rail operation is the selection point: it brings precision-grade offset and drift to single-supply low-voltage designs that older precision op-amps cannot serve. Selection advice: the ARZ suffix denotes SOIC-8 on tape and reel — match the full AD8606ARZ code to your footprint and packing needs. Confirm your offset, drift and noise requirements against the datasheet before substituting for a general-purpose op-amp. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8610AR is an Analog Devices precision JFET-input operational amplifier — for photodiode front ends, precision instrumentation and active filters: 25MHz gain-bandwidth product, JFET input stage with picoamp-level bias current, low offset voltage, SOIC-8 package. The JFET inputs draw negligible bias current, so high-impedance sensor interfaces avoid the loading errors that bipolar-input op amps introduce; the 25MHz bandwidth handles fast signal chains while maintaining precision DC accuracy. Business impact: precision JFET op amps command a premium but eliminate an entire class of front-end error — designs that need both speed and high input impedance have few alternatives at this performance level. Selection advice: the AR suffix denotes SOIC-8 — for space-constrained layouts consider the ARMZ (MSOP) variant; the AD8610 is the single version — for dual-channel designs the AD8620 shares the same core. Ranked #7 on the hqew.com hot list (2026-10-05). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM7801-8BRIZ is an Analog Devices 25 MHz isolated ADC with sigma-delta modulated bit-stream output in 8-lead wide-body SOIC, for shunt current sensing in motor drives, solar inverters, and power converters. It delivers 16 bits with no missing codes over a +/-320 mV full-scale input, 88 dB typical SNR, and 5700 V rms isolation with 200 kV per us minimum common-mode transient immunity, so the controller side stays protected from noisy high-voltage power stages. The benefit is replacing an ADC plus optocoupler pair with one isolated part: the digital output crosses the barrier directly, cutting board area and preserving accuracy in high-dV/dt environments. Selection advice: the output is a pulse-density bit stream, not a parallel word, so your controller or FPGA must implement a sinc3 decimation filter; match the clock rate to your bandwidth and SNR target per the datasheet. The 8BRIZ code is the tube-packed wide-body SOIC version; for reel packing order the -RL code. Listed in DigiKey New Product Arrivals. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM7801-8BRIZ-RL is the tape-and-reel packing of the Analog Devices 25 MHz isolated ADC with sigma-delta modulated bit-stream output in 8-lead wide-body SOIC, for production runs of shunt current sensing in motor drives, solar inverters, and power converters. It delivers 16 bits with no missing codes over a +/-320 mV full-scale input, 88 dB typical SNR, and 5700 V rms isolation with 200 kV per us minimum common-mode transient immunity, so the controller side stays protected from noisy high-voltage power stages. The benefit is replacing an ADC plus optocoupler pair with one isolated part: the digital output crosses the barrier directly, cutting board area and preserving accuracy in high-dV/dt environments. Selection advice: the output is a pulse-density bit stream, not a parallel word, so your controller or FPGA must implement a sinc3 decimation filter; match the clock rate to your bandwidth and SNR target per the datasheet. The -RL suffix denotes reel packing; for tube packing order the base 8BRIZ code. Listed in DigiKey New Product Arrivals. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX31855KASA+T is an Analog Devices (Maxim) cold-junction-compensated K-type thermocouple-to-digital converter in 8-pin SOIC, tape and reel — for industrial temperature sensing: HVAC, appliances and process monitoring. 14-bit conversion with 0.25 °C resolution and integrated cold-junction compensation is the selection point: direct thermocouple-to-digital in one chip, no calibration tables. Selection advice: the K in KASA+T denotes K-type (-200 °C to +1350 °C range); sibling variants cover J, N, T, S, R and E types — match the letter to your thermocouple, they are not interchangeable; the read-only SPI interface suits simple MCU polling; note it is designed for ungrounded thermocouples. 3.0 V to 3.6 V supply. ADI lists this part as Active. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.