MAX14783EASA+

MAX3485ESA+ is a Maxim (Analog Devices) MAX3485 3.3 V half-duplex RS-485/RS-422 transceiver — up to 10 Mbps, one driver plus one receiver, in 8-pin SOIC, tube packing (100 per tube; T suffix is the reel), -40 to +85 °C. The 3.3 V single supply with 5 V-logic interoperability is the selection point: RS-485 on modern 3.3 V logic rails without level translation or charge pumps. Selection advice: the MAX3485 driver is not slew-rate limited, so it reaches 10 Mbps — for EMI-sensitive or long unterminated runs choose the slew-limited MAX3483 (250 kbps) instead. Half-duplex suits two-wire RS-485 buses with up to 32 nodes; for four-wire full-duplex use the MAX3490/91. The fail-safe receiver guarantees a logic-high on open inputs, and driver short-circuit plus thermal shutdown protect the bus. Match the full MAX3485ESA+ code — the + denotes lead-free, ESA is the SO-8 package, and tube versus reel matters for your assembly line. Evidence: Maxim MAX3485 datasheet and TME/LCSC listings confirm 3.3 V, 10 Mbps, half-duplex, SO-8 and -40 to +85 °C. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX485ESA+T is a low-power RS-485/RS-422 transceiver from Analog Devices (Maxim Integrated) in an 8-pin SOIC package, for industrial networks, building automation and long-distance serial links. Its advantage is the RS-485 physical layer itself: differential signaling over twisted pair reaches hundreds of meters and resists industrial noise far better than single-ended UART. Selection advice: the +T denotes the lead-free configuration on tape and reel — match the full code to your compliance and assembly requirements. RS-485 is a half-duplex bus: confirm your network needs biasing and termination resistors at the bus ends, and that only one driver is enabled at a time in your protocol. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot and traceability before quotation and reply within 24 hours.

SN65HVD3082EDR is a Texas Instruments SN65HVD3082E low-power half-duplex RS-485 transceiver — up to 200 kbps signaling rate, single 5 V supply, 8-pin SOIC, tape-and-reel packing of 2500 (R suffix; EP is the PDIP tube version), -40 to +85 °C. The low power and robustness are the selection point: 0.3 mA typical supply current, 1/8-unit-load input supporting up to 256 nodes on the bus, 15 kV bus-pin ESD protection and fail-safe receiver for open/idle lines. Selection advice: the 3082E is the 200 kbps variant — for 1 Mbps choose SN65HVD3085E or for 20 Mbps SN65HVD3088E, which are pin-compatible upgrades in the same family. This is half-duplex (one driver, one receiver); full-duplex RS-422/485 needs a different device. TI lists this code as Active. Evidence: TI SNx5HVD308xE datasheet (ordering information and package addendum) confirms 200 kbps, SOIC-8, 2500/reel packing and -40 to +85 °C. Match the full SN65HVD3082EDR code for data rate, package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ST3485ECDR is an STMicroelectronics 3.3 V half-duplex RS-485/RS-422 transceiver in SO-8, tape and reel — guaranteed data rate of at least 12 Mbps, ±15 kV HBM / ±8 kV IEC 61000-4-2 contact ESD, standard 75176 pinout, 1 µA shutdown mode, −7 V to +12 V common-mode range, rated 0 °C to +70 °C. The 3.3 V supply with true 12 Mbps is the selection point: it runs directly from a 3.3 V MCU rail with no level translation, while older 5 V-only transceivers force an extra regulator or translator onto the board. Selection advice: the ECDR code is the commercial-temperature SO-8 reel version — the ST3485EBDR is the −40 °C to +85 °C industrial version in the same SO-8 footprint and a direct drop-in for wider ambient ranges; the ST3485ECN is the DIP-8 tube version for through-hole builds only. ST lists this code Active and shows stock on its official store; DigiKey also lists it as Active and available for ordering. Evidence: the ST official store page and ST3485 datasheet confirm the ordering code, 12 Mbps, ±15 kV ESD, SO-8 reel and Active status. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

THVD2450DRBR is a Texas Instruments ±70V fault-protected RS-485 transceiver in 8-pin SON (3x3mm) — for rugged industrial field buses where wiring faults are a fact of life: PLC I/O, motor drives and building automation. 50 Mbps data rate, 3V-to-5.5V supply, ±25V extended common-mode range, integrated IEC ESD protection, and -40 to +125°C operation. Selection advice: the 2450 is the 50 Mbps speed grade — for 500 kbps the THVD2410 costs less in the same footprint; the DRBR code is the SON-8 package — for drop-in SOIC compatibility specify the DR code. 1/8 unit load allows 256 nodes on one bus. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM1201ARZ is an Analog Devices ADuM1201 dual-channel digital isolator in 8-lead narrow-body SOIC — 1/1 channel direction configuration, 1 Mbps data rate, 2500 Vrms isolation, 2.7 to 5.5 V supplies with 3 V/5 V level translation, tube packing (ARZ; ARZ-RL7 is the reel version), -40 to +105 °C. The 1/1 direction is the selection point: one channel each way for full-duplex signals like UART Tx/Rx or single-wire buses, using iCoupler magnetic coupling instead of LEDs — no optocoupler aging and 25 kV/µs transient immunity. Selection advice: for two channels in the same direction choose ADuM1200, not ADuM1201; match the ARZ code for tube packing. For SPI or high-speed data isolation choose a higher-rate iCoupler grade. Analog Devices lists this code as Active. Evidence: ADuM1200/ADuM1201 datasheet and DigiKey listings confirm 1 Mbps, 1/1 direction, 2500 Vrms, 8-SOIC tube packing and -40 to +105 °C. Match the full ADUM1201ARZ code for direction and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM1201ARZ-RL7 is an Analog Devices iCoupler dual-channel digital isolator in SOIC-8, tape and reel — for isolating high-speed logic signals: SPI lines, UART and general-purpose data across ground domains. 2500 VRMS magnetic isolation with 1 Mbps and 25 kV per microsecond transient immunity is the selection point: optocoupler-free isolation in an 8-pin package. Selection advice: the RL7 suffix denotes tape and reel on a 7-inch reel — for tube packing, check the non-RL7 ordering code. Both channels run the same direction (1/1) — for opposite-direction pairs such as TX plus RX, the ADUM1201 is not the part; check the channel-direction code in the ADUM120x family before ordering. 2.7 V to 5.5 V on each side allows mixed-voltage isolation; −40 °C to +105 °C. ADI lists this part as Active through distribution. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADM2483BRWZ is an Analog Devices iCoupler isolated RS-485/RS-422 transceiver in wide-body SOIC-16, tube — for isolated serial links in industrial automation, motor control and data acquisition. 2500 VRMS magnetic isolation with 500 kbps half-duplex RS-485 is the selection point: signal isolation without optocouplers. Selection advice: the BRWZ suffix denotes the 16-lead wide-body SOIC in tube packing — for tape and reel, check the REEL-suffixed code. Important distinction from the ADM2587EBRWZ-REEL7 on this site: the ADM2483 does not integrate isolated power — you must provide an isolated supply for the bus side, while the ADM2587 includes isoPower and needs none. 3 V or 5 V operation; −40 °C to +85 °C. ADI lists this part as Active through distribution. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADM2587EBRWZ-REEL7 is an Analog Devices isoPower isolated RS-485/RS-422 transceiver in 20-lead wide-body SOIC, tape and reel — for isolated field buses where board space is tight: one chip replaces the transceiver plus the isolated DC-DC module. Integrated isolated power with 2500 VRMS signal isolation and 500 kbps is the selection point: no external isolated supply needed, unlike the ADM2483BRWZ on this site. Selection advice: the REEL7 suffix denotes tape and reel on a 7-inch reel — for tube packing, check the non-REEL ordering code. ±15 kV ESD and up to 256 nodes on one bus suit long multipoint lines. 3.3 V or 5 V operation; −40 °C to +85 °C. ADI lists this part as Active through distribution. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ISO1044BD is a Texas Instruments galvanically isolated CAN FD transceiver in SOIC-8 — for CAN buses that cross ground domains: EV battery packs, solar inverters and motor drives where noise currents must not enter the local ground. 5 Mbps CAN FD data rate, ±58V DC bus fault protection, 3000 VRMS isolation barrier, and -40 to +125°C operation. Selection advice: this is the CAN FD generation — for classic CAN isolation the ISO1050 on this site is the established choice; the SOIC-8 D package replaces optocoupler-plus-transceiver discrete solutions in a fraction of the board area. Pair with an isolated power supply for a complete isolated CAN node. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Skyworks and Qorvo expect to close their $22 billion merger on or about October 5, 2026. What the deal changes for RF front-end buyers — and a five-point checklist for before and after close.