AD8672ARMZ

AD8605ARTZ-REEL7 is an Analog Devices precision single-channel CMOS operational amplifier — rail-to-rail input and output, 10 MHz gain-bandwidth product, 5 V/µs slew rate — with 20 µV typical / 80 µV maximum offset voltage, 0.2 pA input bias current and 8 nV/√Hz voltage noise, on a single 2.7 to 5.5 V supply, in SOT-23-5, operating -40 to +125 °C. ADI DigiTrim technology is the selection point: laser-trim-grade offset without laser trimming, so microvolt precision holds across production lots for sensor front ends, photodiode amplifiers, active filters and audio stages. Selection advice: the femtoamp-class bias current suits high-impedance sources that would be loaded by bipolar op amps — photodiodes, piezoelectric and electret sensors — but confirm your supply rail is within 5.5 V and that one channel is enough, since the dual AD8606 and quad AD8608 cover multi-channel designs in the same family. The REEL7 suffix is the 7-inch reel (3000 pieces) — match the full code if your line needs a different reel size or tube packing. This is a general-purpose precision part, not automotive qualified. Evidence: ADI datasheet and distributor listings confirm 10 MHz, 5 V/µs, 80 µV max offset, 0.2 pA bias and SOT-23-5. Confirm lead time and availability at RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8606ARZ is a dual rail-to-rail precision operational amplifier from Analog Devices in an 8-pin SOIC package — for low-voltage precision systems, data acquisition front ends and medical instrumentation. The combination of precision DC specs with rail-to-rail operation is the selection point: it brings precision-grade offset and drift to single-supply low-voltage designs that older precision op-amps cannot serve. Selection advice: the ARZ suffix denotes SOIC-8 on tape and reel — match the full AD8606ARZ code to your footprint and packing needs. Confirm your offset, drift and noise requirements against the datasheet before substituting for a general-purpose op-amp. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8610AR is an Analog Devices precision JFET-input operational amplifier — for photodiode front ends, precision instrumentation and active filters: 25MHz gain-bandwidth product, JFET input stage with picoamp-level bias current, low offset voltage, SOIC-8 package. The JFET inputs draw negligible bias current, so high-impedance sensor interfaces avoid the loading errors that bipolar-input op amps introduce; the 25MHz bandwidth handles fast signal chains while maintaining precision DC accuracy. Business impact: precision JFET op amps command a premium but eliminate an entire class of front-end error — designs that need both speed and high input impedance have few alternatives at this performance level. Selection advice: the AR suffix denotes SOIC-8 — for space-constrained layouts consider the ARMZ (MSOP) variant; the AD8610 is the single version — for dual-channel designs the AD8620 shares the same core. Ranked #7 on the hqew.com hot list (2026-10-05). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADA4077-2ARZ is an Analog Devices dual precision operational amplifier in 8-lead SOIC, tube packing — 15 µV typical input offset (50 µV max A-grade), 0.25 µV/°C drift, 3.6 MHz gain-bandwidth, 1.2 V/µs slew rate, 1 nA input bias and 400 µA per channel, specified over −40 °C to +125 °C on 5 V to 30 V supplies (±2.5 V to ±15 V). Unity-gain stable with no phase reversal and stable into 1000 pF capacitive loads. The offset-plus-drift combination is the selection point: thermocouple, RTD and strain-gauge front ends hold calibration across temperature without trimming, which is the whole value proposition of a precision op amp. Selection advice: the ARZ code is the tube version — ARZ-R7/ARZ-RL is the same die on tape and reel for pick-and-place; this is not a rail-to-rail output part, so size your signal swing inside the ±15 V rails. For single-channel or quad layouts use the ADA4077-1/ADA4077-4. Evidence: LCSC and element14/Newark listings confirm 15 µV, 3.6 MHz, −40 to +125 °C, SOIC-8 and wide distributor stock. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

OP07CDR is a Texas Instruments precision operational amplifier in SOIC-8 — for DC measurement front-ends: bridge amplifiers, thermocouple conditioning and precision integrators. 150 µV maximum input offset (C-grade), ±14 nA maximum bias current, 600 kHz gain-bandwidth, ±3 V to ±18 V supply, near-zero offset drift. Heat evidence: precision analog remains on firm allocation as instrumentation and industrial demand holds — the OP07 is the classic precision bipolar op-amp with decades of continuous production. Selection advice: the CDR suffix is SOIC-8 on reel for SMT — same die as the DIP OP07CP; note the older OP07CD (tube) is obsolete, always order the R (reel) variant for current production. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

OPA2188AID is a Texas Instruments zero-drift dual operational amplifier in 8-pin SOIC — for precision signal chains where offset drift destroys accuracy over temperature: bridge sensors, thermocouple front ends and precision current sensing. 25 µV maximum offset voltage with 0.03 µV/°C drift, 8.8 nV/√Hz noise, 2 MHz gain bandwidth, rail-to-rail output, on 4 V to 36 V supplies at 475 µA maximum per channel. The auto-zero architecture is the selection point: offset and drift an order of magnitude better than standard bipolar op-amps, with no 1/f noise corner to corrupt slow measurements. Selection advice: this is the precision step up from the LM358 on this site — specify the OPA2188 when the error budget cannot tolerate millivolt offsets; for cost-driven non-precision use the LM358 remains the economical choice. The AID code is the tube SOIC — AIDR is the reel. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD4003BRMZ is an Analog Devices 18-bit, 2 MSPS successive-approximation ADC in 10-lead MSOP — for precision data acquisition that needs both speed and DC accuracy: automatic test equipment, portable instruments and machine automation. ±1 LSB maximum INL with 100.5 dB SNR and -123 dB THD at 1 kHz, no latency or pipeline delay with first conversion accurate, and a high-Z input mode plus long acquisition phase that lets low-power precision amplifiers drive it directly — no dedicated high-speed ADC driver required. Input span compression runs the driver and ADC from common rails without a negative supply. Selection advice: the BRMZ code is the MSOP-10 version — for 16-bit at lower cost the AD4000 is the family sibling; the 1.8 V single supply with 1.71–5.5 V logic interface suits battery-powered field instruments. Daisy-chainable SPI simplifies multichannel layouts. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD5689RBRUZ is an Analog Devices dual 16-bit buffered voltage-output DAC in 16-lead TSSOP — for precision setpoint and calibration outputs in industrial control: PLC I/O cards, data acquisition and optical transceiver biasing. ±2 LSB maximum INL at 16 bits, an internal 2.5 V reference with 2 ppm/°C typical drift (no external reference needed), user-selectable gain of 1 or 2 for 2.5 V or 5 V full scale, 20 mA drive capability within 0.5 V of the rails, and 50 MHz SPI with daisy-chain and readback. Power-on reset to zero or midscale keeps outputs safe at startup. Selection advice: the BRUZ code is the TSSOP-16 tube version — for single-channel designs the AD5683R is the family sibling; against the octal DAC80508 on this site, the AD5689R is the pick for dual-channel precision nodes where per-channel accuracy matters more than channel count. The 4 µA power-down mode suits battery-backed calibration circuits. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD5761RARUZ is an Analog Devices 16-bit voltage-output DAC with integrated 2.5V reference in TSSOP-16 — for industrial automation outputs where one chip must cover every standard range: PLC analog outputs, servo control and process control. Eight software-programmable output ranges (0-5V, 0-10V, 0-20V, ±3V, ±5V, ±10V and more) with 5% overrange, a ±2ppm/°C drift reference and ±2-LSB maximum INL mean the output stays accurate without external trimming. Selection advice: the ARUZ code is the TSSOP-16 reel variant — for the smaller 3x3mm LFCSP specify the ACPZ; the AD5721R is the 12-bit cost-down sibling. Single-supply 4.75V-to-30V or dual-supply operation covers both unipolar and bipolar systems — confirm your supply configuration against the range table. Asynchronous LDAC and reset-to-zero/midscale suit safety-critical outputs. Parameters verified against Analog Devices documentation and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620ARZ is a low-power instrumentation amplifier from Analog Devices in an 8-pin SOIC package, with gain set by a single external resistor — for bridge sensors, strain gauges and other small differential signals. Its advantage is the classic three-op-amp instrumentation topology in one package: high common-mode rejection with minimal external circuitry, which shortens precision front-end design. Selection advice: the ARZ suffix denotes the standard grade in SOIC-8 on tape and reel — the AD620 also ships in DIP and higher grades, so match the full code to your footprint and accuracy requirements. Gain is set by one resistor value, so confirm your gain calculation against the datasheet formula during design. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.