SN65HVD3082EDR

THVD2450DRBR is a Texas Instruments ±70V fault-protected RS-485 transceiver in 8-pin SON (3x3mm) — for rugged industrial field buses where wiring faults are a fact of life: PLC I/O, motor drives and building automation. 50 Mbps data rate, 3V-to-5.5V supply, ±25V extended common-mode range, integrated IEC ESD protection, and -40 to +125°C operation. Selection advice: the 2450 is the 50 Mbps speed grade — for 500 kbps the THVD2410 costs less in the same footprint; the DRBR code is the SON-8 package — for drop-in SOIC compatibility specify the DR code. 1/8 unit load allows 256 nodes on one bus. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX14783EASA+ is an Analog Devices high-speed RS-485 transceiver in SOIC-8 — for long cable runs where speed and ESD robustness both matter: encoder interfaces, motion controllers and field-bus backplanes. 42 Mbps data rate, ±35kV HBM ESD protection, 3V-to-5.5V supply, hot-swap capability, and true fail-safe receiver. Selection advice: the ASA+ code is the SOIC-8 -40 to +125°C variant — for smaller footprints the ATA+ TDFN-EP is the alternative; against the TI THVD2450 on this site, the MAX14783E trades fault voltage for higher ESD rating — match the protection priority to your installation environment. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX3485ESA+ is a Maxim (Analog Devices) MAX3485 3.3 V half-duplex RS-485/RS-422 transceiver — up to 10 Mbps, one driver plus one receiver, in 8-pin SOIC, tube packing (100 per tube; T suffix is the reel), -40 to +85 °C. The 3.3 V single supply with 5 V-logic interoperability is the selection point: RS-485 on modern 3.3 V logic rails without level translation or charge pumps. Selection advice: the MAX3485 driver is not slew-rate limited, so it reaches 10 Mbps — for EMI-sensitive or long unterminated runs choose the slew-limited MAX3483 (250 kbps) instead. Half-duplex suits two-wire RS-485 buses with up to 32 nodes; for four-wire full-duplex use the MAX3490/91. The fail-safe receiver guarantees a logic-high on open inputs, and driver short-circuit plus thermal shutdown protect the bus. Match the full MAX3485ESA+ code — the + denotes lead-free, ESA is the SO-8 package, and tube versus reel matters for your assembly line. Evidence: Maxim MAX3485 datasheet and TME/LCSC listings confirm 3.3 V, 10 Mbps, half-duplex, SO-8 and -40 to +85 °C. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX485ESA+T is a low-power RS-485/RS-422 transceiver from Analog Devices (Maxim Integrated) in an 8-pin SOIC package, for industrial networks, building automation and long-distance serial links. Its advantage is the RS-485 physical layer itself: differential signaling over twisted pair reaches hundreds of meters and resists industrial noise far better than single-ended UART. Selection advice: the +T denotes the lead-free configuration on tape and reel — match the full code to your compliance and assembly requirements. RS-485 is a half-duplex bus: confirm your network needs biasing and termination resistors at the bus ends, and that only one driver is enabled at a time in your protocol. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot and traceability before quotation and reply within 24 hours.

ST3485ECDR is an STMicroelectronics 3.3 V half-duplex RS-485/RS-422 transceiver in SO-8, tape and reel — guaranteed data rate of at least 12 Mbps, ±15 kV HBM / ±8 kV IEC 61000-4-2 contact ESD, standard 75176 pinout, 1 µA shutdown mode, −7 V to +12 V common-mode range, rated 0 °C to +70 °C. The 3.3 V supply with true 12 Mbps is the selection point: it runs directly from a 3.3 V MCU rail with no level translation, while older 5 V-only transceivers force an extra regulator or translator onto the board. Selection advice: the ECDR code is the commercial-temperature SO-8 reel version — the ST3485EBDR is the −40 °C to +85 °C industrial version in the same SO-8 footprint and a direct drop-in for wider ambient ranges; the ST3485ECN is the DIP-8 tube version for through-hole builds only. ST lists this code Active and shows stock on its official store; DigiKey also lists it as Active and available for ordering. Evidence: the ST official store page and ST3485 datasheet confirm the ordering code, 12 Mbps, ±15 kV ESD, SO-8 reel and Active status. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ISO1044BD is a Texas Instruments galvanically isolated CAN FD transceiver in SOIC-8 — for CAN buses that cross ground domains: EV battery packs, solar inverters and motor drives where noise currents must not enter the local ground. 5 Mbps CAN FD data rate, ±58V DC bus fault protection, 3000 VRMS isolation barrier, and -40 to +125°C operation. Selection advice: this is the CAN FD generation — for classic CAN isolation the ISO1050 on this site is the established choice; the SOIC-8 D package replaces optocoupler-plus-transceiver discrete solutions in a fraction of the board area. Pair with an isolated power supply for a complete isolated CAN node. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN65HVD230DR is a Texas Instruments 3.3 V CAN transceiver in SOIC-8, tape and reel — for industrial automation, motor control and building systems adding CAN bus to 3.3 V MCUs. ISO 11898-compliant 1 Mbps transceiver running from a single 3.3 V supply is the selection point: no 5 V rail needed for the CAN physical layer. Selection advice: the R suffix denotes tape and reel. Low-power standby (370 µA typical) suits battery-backed nodes; ±16 kV HBM bus ESD, thermal shutdown and open-circuit fail-safe harden the bus; up to 120 nodes per bus. It is documented as a low-power 3.3 V replacement for the classic 5 V PCA82C250 footprint — for new native 5 V CAN designs, stay with a 5 V transceiver. Not automotive qualified — for AEC-Q100, ask about the Q1-qualified variant. TI lists this part as Active. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TCAN1044ADRQ1 is a Texas Instruments AEC-Q100 Grade 1 CAN FD transceiver in SOIC-8 — for automotive networks migrating from classic CAN to CAN FD: body control modules, gateways and battery management systems. 5 Mbps CAN FD data rate (2 Mbps classic CAN), ISO 11898-2:2016 compliant, ±58V bus fault protection, and 1.7V-to-5.5V VIO for 3.3V/5V MCU interfacing. Heat evidence: CAN FD is the mandatory upgrade path as vehicle E/E architectures consolidate — every new automotive platform from 2024 onward specifies CAN FD for backbone communication. Selection advice: the A variant adds flexible data-rate support over the base TCAN1044 — for 8 Mbps signal-improvement networks the TJA1462 on this site is the SIC alternative; the DRQ1 code is the SOIC-8 reel version. AEC-Q100 Grade 1 (-40 to +125°C) qualified. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83848IVVX/NOPB is a Texas Instruments DP83848I industrial-temperature 10/100 Mbps Ethernet PHY transceiver — 48-pin LQFP (7 × 7 mm), MII/RMII/SNI MAC interfaces, auto-MDIX, energy-detect mode, JTAG, 3.3 V, tape-and-reel packing of 1000, -40 to +85 °C. The industrial temperature range is the selection point: the I grade covers factory automation and outdoor equipment where commercial-grade PHYs fail, with auto-MDIX eliminating crossover-cable concerns. Selection advice: this is a PHY only — it needs an external MAC (MCU or switch) and a magnetics module. The V suffix is the 48-LQFP package; NOPB is the lead-free RoHS variant. For Gigabit Ethernet choose a different PHY family, since this is strictly 10/100. TI lists this code as Active. Evidence: TI DP83848I datasheet and distributor listings confirm 10/100 Mbps PHY, 48-LQFP, MII/RMII, -40 to +85 °C and 1000/reel packing. Match the full DP83848IVVX/NOPB code for temperature grade and package. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83867ERGZR is a Texas Instruments 10/100/1000BASE-T Gigabit Ethernet PHY in 48-pin VQFN (7x7mm) — for industrial Ethernet nodes where deterministic latency and diagnostics matter: PLCs, machine vision cameras and grid automation. RGMII and SGMII MAC interfaces, IEEE 1588 start-of-frame detection for time-sensitive networking, cable diagnostics, and 8kV IEC 61000-4-2 ESD protection. Selection advice: the E variant covers -40 to +105°C — for commercial 0 to +70°C the CS code costs less, and the IR code targets -40 to +85°C industrial; for 10/100 Mbps only the DP83848 on this site is the economical choice. 457mW full-power draw suits fanless enclosures. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Skyworks and Qorvo expect to close their $22 billion merger on or about October 5, 2026. What the deal changes for RF front-end buyers — and a five-point checklist for before and after close.