ADUM4223BRWZ

ADUM4223ARWZ is an Analog Devices dual-channel isolated half-bridge driver — 16-lead wide-body SOIC, independent high-side and low-side outputs, 4 A peak output, 5 kV rms isolation, grade A UVLO (4.1 V typ), 5 ns channel matching. The 5 ns channel matching is the selection point: tight high/low-side timing for clean half-bridge switching — deadtime accuracy that discrete drivers cannot match. Selection advice: ADI lists the ADUM4223ARWZ as Production. The ARWZ code pins the 16-lead wide-body variant — match it to your footprint; the grade A UVLO suits 5 V logic drive. Verify the 4 A peak against your switch gate charge at the switching frequency, and the isolation working voltage against your safety standard. Evidence: ADI data confirms Production, 16-lead wide-body SOIC, 4 A peak, 5 kV rms isolation, 5 ns matching. Match the full ADUM4223ARWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM4223CRWZ is an Analog Devices iCoupler isolated dual gate driver in wide-body 16-SOIC — 4 A peak output, 5000 VRMS reinforced isolation, two independent isolated channels for high-side and low-side driving, 3.0 V to 5.5 V input supply, 4.5 V to 18 V output drive supply, 49 ns maximum propagation delay with 5 ns channel matching, >25 kV/µs common-mode transient immunity, -40 to +125 °C, tube packing (Z). The C grade is the selection point: 11.0 V UVLO threshold on the output supplies — designed for 12 V gate-drive rails where the driver stays off until the rail is solid. Selection advice: the A/B/C grades differ only in the output-supply UVLO threshold (A 4.1 V, B 7.0 V, C 11.0 V) — pick the grade matching your actual gate-drive voltage. The WBRWZ/WCRWZ codes are the AEC-Q100 automotive variants. Evidence: ADI ADuM3223/4223 datasheet (Rev. I) and distributor listings confirm 4 A, 5000 VRMS, wide-body 16-SOIC and tube packing. Match the full ADUM4223CRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

2EDF7235K is an Infineon EiceDRIVER dual-channel isolated gate driver — PG-TFLGA-13, functional galvanic isolation, tape and reel. The coreless-transformer isolation is the selection point: dual-channel isolated drive in a 5×5 mm package with no optocoupler aging — for SiC/GaN and IGBT stages. Selection advice: lifecycle warning — Infineon lists the 2EDF7235K as discontinued (EOL announced May 2023); for new designs migrate to the current-generation 2EDF7xxx family, and for repairs and legacy builds we source remaining stock. Confirm the exact 2EDF7235K code on the BOM — the EiceDRIVER family spans many current and package variants that are not interchangeable. Evidence: Infineon data confirms discontinued status and the base ordering code. Match the full 2EDF7235K code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

STGAP2DMTR is an ST 1700 V isolated dual-channel gate driver — SO-16, 4 A drive, UVLO protection, galvanic isolation between gate drive signals, tape and reel. The 1700 V isolation is the selection point: dual-channel isolated drive for high-voltage SiC and IGBT stages — industrial drives and solar inverters where 600 V drivers cannot go. Selection advice: ST lists the STGAP2DMTR as Active. The DMTR suffix denotes SO-16 on tape and reel — match it to your footprint; the STGAP2SM is the single-channel narrow-body SO-8 sibling. Verify the isolation working voltage against your safety standard — 1700 V rating suits 1200 V-class power stages. Evidence: ST data confirms Active, 1700 V isolation, dual channel, SO-16, 4 A. Match the full STGAP2DMTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

STGAP2HDMTR is an STMicroelectronics dual-channel galvanically isolated gate driver in wide-body SO-36W — 4 A sink/source per channel at 25 °C, 75 ns propagation delay, ±100 V/ns common-mode transient immunity, tape-and-reel packing (MTR), −40 to +125 °C. Galvanic isolation per the ST datasheet: 6 kV surge rating, 3500 VRMS per UL 1577, IEC 60747-17 certified. The isolated dual-channel topology is the selection point: one part drives both sides of a half bridge or full bridge while keeping the control ground fully separated from the power stage, cutting the board space and discrete isolation parts a two-chip solution needs. Separate open and close outputs plus the Miller clamp let you tune turn-on/turn-off independently, while UVLO on both supplies, thermal shutdown, SD, BRAKE and configurable interlocking with dead time simplify shoot-through-proof designs for motor drives, inverters and EV charging. Selection advice: this is the dual (D) member of the STGAP2 family — the STGAP2HSx are the single-channel wide-body SO-8W parts; pick D when one package must cover both bridge legs, and keep its pinout off-limits as a drop-in for single-channel drivers. ST lists STGAP2HDMTR as Active. Evidence: ST STGAP2HD datasheet and ST eStore confirm 4 A, 75 ns, ±100 V/ns CMTI, isolation ratings, SO-36W and tape-and-reel packing. Match the full STGAP2HDMTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADM3054BRWZ is an Analog Devices isolated high-speed CAN transceiver — 16-lead wide-body SOIC, 5 kV rms signal isolation, bus protection, up to 1 Mbps, −40 to +125 °C. The integrated 5 kV isolation is the selection point: isolated CAN in one chip — no separate isolator plus transceiver, which halves the BOM for isolated CAN nodes. Selection advice: ADI lists the ADM3054BRWZ as Production. The BRWZ code pins the 16-lead wide-body SOIC — match it to your footprint. Verify the isolation working voltage against your safety standard, and note the isolated side needs its own supply — budget the isolated DC-DC in the BOM. Evidence: ADI data confirms Production, 16-lead wide-body SOIC, 5 kV rms isolation, 1 Mbps. Match the full ADM3054BRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM4160BRWZ-RL is an Analog Devices USB 2.0 digital isolator in 16-lead SOIC wide body, tape and reel — iCoupler-based, 5 kV rms reinforced isolation (UL 1577), automatic USB direction detection, 4.5–5.5 V VBUS or 3.3 V operation, upstream short-circuit protection, >25 kV/µs common-mode transient immunity, rated to 105 °C. A single chip replaces the discrete optocoupler-plus-logic approach for isolated USB. Selection advice: this part supports USB low speed (1.5 Mbps) and full speed (12 Mbps) only — it does not do USB 2.0 high speed (480 Mbps); for high-speed isolation you need a different device. The RWZ code is the wide-body SOIC-16 with reinforced creepage; RL is the reel version. Target applications are medical (IEC 60601-1) and industrial USB ports where isolation is a safety requirement. Evidence: the ADI ADuM4160 datasheet confirms 5 kV rms, 1.5/12 Mbps, SOIC-16 wide body and the speed limitation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS3231M+ is an Analog Devices (Maxim) I2C real-time clock in wide SOIC-16 — for timekeeping that stays accurate without calibration: meters, data loggers and access systems. The ±5 ppm MEMS-based accuracy is the selection point: seconds-per-month accuracy with no external crystal. Selection advice: the M+ denotes the MEMS variant in wide SOIC-16 — pick it over the DS1307 when accuracy matters and board space allows; the SN# (TCXO) variant offers tighter ±2 ppm. Battery backup keeps time through power loss. ADI lists this part as PRODUCTION. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS3231SN# is an Analog Devices (Maxim) extremely accurate I2C real-time clock with integrated TCXO and crystal in 16-pin SO — for timekeeping that stays accurate without calibration: meters, data loggers and access systems. The ±2 ppm integrated TCXO is the selection point: seconds-per-month accuracy with no external crystal or trimming. Selection advice: the SN# suffix denotes 16-pin SO — pick the DS3231 over the cheaper DS1307 when accuracy matters; the DS1307 needs an external crystal and drifts far more. Battery backup keeps time through power loss. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX232ESE+ is an Analog Devices (Maxim) dual RS-232 driver/receiver with on-chip charge pump in 16-pin SOIC — for legacy serial ports: industrial consoles, POS terminals and instrumentation. The integrated charge pump is the selection point: true RS-232 levels from a single 5 V supply, no ±12 V rails. Selection advice: the ESE+ denotes 16-pin SOIC — for 3.3 V systems, the MAX3232 is the pin-compatible low-voltage sibling; for new designs, consider USB instead of RS-232. Four external charge-pump capacitors required per the datasheet. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.