INA219BIDCNR

INA219AIDCNT is a Texas Instruments INA219 zero-drift, bidirectional current and power monitor with I2C interface — senses bus voltages from 0 to 26 V, reports current, voltage and power directly in amperes and watts through calibration and multiplier registers, in 8-pin SOT-23, tube packing (DCNT), -40 to +125 °C. Direct digital readouts are the selection point: no analog signal chain or ADC math in firmware — the MCU reads current and power over I2C for servers, telecom, battery chargers and power-supply telemetry. Selection advice: this is the A grade; the B grade (INA219B) tightens accuracy to 0.5% over temperature for precision billing or calibration use. Sixteen programmable I2C addresses allow many monitors on one bus; for analog-output monitoring at lower cost consider the INA210-INA214 family instead. Note DCNT is the tube variant; DCNR is the reel version. Evidence: TI INA219 datasheet (SBOS448G) and distributor listings confirm 0-26 V sensing, I2C, SOT-23-8 and tube packing. Match the full INA219AIDCNT code for grade and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

INA219BIDCNT is a Texas Instruments B-grade zero-drift bidirectional current/power monitor in SOT-23-8, 250-piece small reel — 0.5% maximum accuracy over temperature (B grade), 0–26 V bus sensing, 3–5.5 V supply, 12-bit ADC with programmable averaging to 128 samples, calibration register for direct ampere and watt readouts, 16 programmable I2C addresses, −40 °C to +125 °C. The small reel is the selection point: the identical B-grade die and SOT-23-8 package as INA219BIDCNR, but on 250-piece reel — prototypes, pilot runs and low-volume repairs get the tighter 0.5% grade without committing to a 3000-piece reel. Selection advice: T versus R is purely a packing choice — same silicon, same SOT-23-8 footprint, so a design qualified on the T reel moves to the R reel for volume with no requalification. Do not confuse with the A grade (1% accuracy) or the SOIC-8 INA219BIDR. Evidence: TI INA219 datasheet (Rev. G) confirms B-grade 0.5%, SOT-23-8 and the 250-reel option. Match the full INA219BIDCNT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists INA219AIDR as an ACTIVE digital current and power monitor in SOIC-8 — for I2C-based power measurements with 0–26 V common-mode range, 12-bit resolution and programmable gain. The digital I2C output is the selection point: current, voltage and computed power read directly by the host MCU, no analog signal chain needed. Selection advice: the AIDR suffix denotes SOIC-8 on tape and reel — the tube-packing INA219AID code is obsolete, so for production specify INA219AIDR. Confirm your shunt resistor value and current range against the datasheet before committing. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

INA219BIDR is a Texas Instruments B-grade zero-drift bidirectional current/power monitor in SOIC-8, 3000-piece large reel — 0.5% maximum accuracy over temperature (B grade), 0–26 V bus sensing, 3–5.5 V supply, 12-bit ADC with programmable averaging to 128 samples, calibration register for direct ampere and watt readouts, 16 programmable I2C addresses, −40 °C to +125 °C. The SOIC-8 package is the selection point: the same B-grade 0.5% die as the SOT-23 variants, but in a package that hand-solders and reworks comfortably — a real advantage for repair, rework and low-cost assembly flows. Selection advice: the D code is SOIC-8 — not footprint-compatible with the SOT-23-8 INA219BIDCNR/IDCNT, so pick the package before the PCB is taped out. The R suffix is the 3000-piece reel for volume; for small runs the SOT-23 T-reel variant is the economical prototype path. Evidence: TI INA219 datasheet (Rev. G) confirms B-grade 0.5%, SOIC-8 and the 3000-reel option. Match the full INA219BIDR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

INA219AIDCNR is a Texas Instruments zero-drift bidirectional current and power monitor in SOT-23-8, tape and reel — for power telemetry: servers, telecom and test equipment. Reporting bus voltage, shunt current and computed power over I2C is the selection point: full power telemetry from one chip plus a shunt resistor. Selection advice: the DCNR suffix denotes SOT-23-8 in 3000-piece tape and reel — for the SOIC-8 package, the INA219AIDR is the sibling; the A grade versus the higher-accuracy B grade — pick B only if your error budget needs it; the 0 V to 26 V bus range covers most DC rails. 3 V to 5.5 V supply. TI lists this part as ACTIVE. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists ADS1115IDGSR as an ACTIVE 16-bit delta-sigma ADC in VSSOP-10, with 860 SPS sampling, 4 multiplexed channels and I2C interface. The 16-bit resolution is the procurement-relevant advantage: it resolves small sensor signals that a 10- or 12-bit converter would bury in quantization noise, which is why this part is the default choice for precision data-acquisition front ends. Selection advice: the IDGSR suffix pins the VSSOP-10 package on tape and reel — the ADS1115 also ships in other packages, so match the full code to your layout. Four multiplexed inputs versus the two-channel ADS1113 and single-ended/differential options are the family decision points; confirm your channel count and interface (I2C here, not SPI) against the datasheet before substituting. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDGST is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter — four single-ended or two differential inputs, programmable gain amplifier with full-scale ranges from ±6.144 V down to ±0.256 V, programmable data rates from 8 to 860 SPS, I2C interface with four pin-selectable addresses, in 10-pin VSSOP, tube packing (DGST), -40 to +125 °C. The integrated PGA, low-drift reference and oscillator are the selection point: true precision ADC performance with no external reference or clock, ideal for battery-voltage monitoring, temperature measurement and portable instrumentation. Selection advice: 860 SPS suits slow precision signals — for kilohertz sampling choose an SAR ADC (ADS868x family) instead. The built-in comparator can drive an alert pin for threshold monitoring without MCU polling, and 16 I2C addresses (four pins × four states) let you run multiple converters on one bus. Note this exact ADS1115IDGST code is the tube variant; IDGSR is the reel version. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA ranges, 8-860 SPS, VSSOP-10 and tube packing. Match the full ADS1115IDGST code for packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDYNR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin SOT-23 package — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing (DYNR), -40 to +125 °C. The SOT-23 footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in the smallest ADS1115 package for space-constrained sensor nodes. Selection advice: same die and performance as the VSSOP (IDGST) and X2QFN (IRUGR) variants — choose this code for the SOT-23 footprint and reel packing. The 150 µA active current and single-shot power-down mode suit battery designs; for 24-bit resolution or excitation sources step up to the ADS1220. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA, I2C, SOT-23-10 and reel packing. Match the full ADS1115IDYNR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin X2QFN package (2 × 1.5 × 0.4 mm) — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing of 3000 (IRUGR; IRUGT is the small reel), -40 to +125 °C. The 2 × 1.5 mm footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in one of the smallest ADC packages available, for wearables and dense sensor boards. Selection advice: same die and performance as the VSSOP (IDGSR) and SOT-23 (IDYNR) variants — choose this code for the X2QFN footprint and 3000-reel packing. Leadless QFN needs reflow assembly and good layout practice; for hand-soldering prototypes choose the VSSOP variant. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D), TI pack addendum and DigiKey listings confirm 16-bit, PGA, I2C, X2QFN-10 and 3000-reel packing. Match the full ADS1115IRUGR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGT is a Texas Instruments 16-bit delta-sigma ADC in 10-pin X2QFN (2.0 × 1.5 × 0.4 mm), 250-piece small reel — I2C interface, four single-ended or two differential inputs, programmable gain amplifier (±256 mV to ±6.144 V), internal low-drift reference and oscillator, programmable comparator, 8 to 860 SPS, 2.0–5.5 V, 150 µA, −40 °C to +125 °C. The integration is the selection point: PGA, MUX, reference, oscillator and comparator on one 2×1.5 mm die means a complete sensor front end with no external analog support chips. Selection advice: the RUG package code is the X2QFN — ADS1115IDGST is the same die in VSSOP-10 on 250-piece small reel — the easier-to-assemble alternative for designs that do not need the 2×1.5 mm X2QFN footprint, not interchangeable on the same footprint. Against the 12-bit ADS1015: pick the ADS1115 for resolution (weighing, precision sensing), the ADS1015 for speed (3300 SPS). The ADDR pin gives four I2C addresses, so up to four devices share one bus. Evidence: TI ADS1115 datasheet (ordering addendum) and distributor listings confirm X2QFN-10, 250-reel, 16-bit, I2C and −40 to +125 °C. Match the full ADS1115IRUGT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.