TL072CPWR

Texas Instruments lists TL072CP as a dual JFET-input operational amplifier in PDIP-8 — for high-input-impedance analog signal paths such as guitar preamps, piezo buffers and electrometer front ends. The JFET input stage is the selection point: picoamp-level input bias current that bipolar op-amps cannot match, which is why the TL072 dominated audio and sensor front ends for decades. Selection advice: the CP suffix denotes PDIP-8 in tube packaging — the TL072 also ships in SOIC-8, so match the full TL072CP code to your footprint and packing needs. For lower noise, compare against the NE5532; for the classic JFET-input behavior, match this code exactly. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TL072IDR is a Texas Instruments TL072 dual JFET-input operational amplifier in SOIC-8, 2500-piece tape and reel — 3 MHz gain-bandwidth, 13 V per microsecond slew rate, JFET inputs with picoamp bias current, common-mode range includes VCC+, 1.4 mA per channel, industrial −40 °C to +85 °C grade. The IDR code is the selection point: the industrial-grade die in SOIC-8 on reel — the workhorse choice for production audio, measurement and control boards that must work below freezing or in hot enclosures. Selection advice: against the commercial TL072CPWR (0 to 70 °C, TSSOP-8), pick the IDR when the operating environment demands the wider range; against the PDIP TL072IP, pick the IDR for SMD assembly. Same JFET-input advantages: negligible bias-current error on high-impedance sources, 13 V per microsecond slew for clean audio transients. Not rail-to-rail output. Evidence: TI TL072 datasheet ordering information confirms SOIC-8 (D), 2500-piece reel and the I-grade −40 to +85 °C range. Match the full TL072IDR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TL072IP is a Texas Instruments TL072 dual JFET-input operational amplifier in PDIP-8, tube packaging — 3 MHz gain-bandwidth, 13 V per microsecond slew rate, JFET inputs with picoamp bias current, common-mode range includes VCC+, 1.4 mA per channel, industrial −40 °C to +85 °C grade. The IP code is the selection point: the industrial-grade die in through-hole PDIP-8 — the prototyping, teaching-lab and repair choice, socketable and hand-solderable, with the wider temperature range the commercial CP codes lack. Selection advice: pick the IP for breadboards, one-offs and field repairs; pick the IDR (SOIC-8 reel) or CPWR (TSSOP-8 reel) for production — same die, different assembly flow. The JFET input keeps bias-current errors negligible on high-impedance audio and sensor sources. Not rail-to-rail output. Evidence: TI TL072 datasheet ordering information and distributor listings confirm PDIP-8 (P), tube packaging and the I-grade −40 to +85 °C range. Match the full TL072IP code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

INA240A1PWR is a Texas Instruments bidirectional current-sense amplifier with enhanced PWM rejection — for in-line motor phase current and power-rail telemetry where switching noise corrupts ordinary sensing: -4 V to 80 V common-mode range, 20 V/V fixed gain (A1), ±25 µV max offset, 132 dB DC CMRR, in 8-pin TSSOP, -40°C to +125°C. The enhanced PWM rejection suppresses large common-mode transients without output ripple, enabling accurate current measurement directly in the switching path — the same telemetry function datacenter PMBus modules integrate, here as a discrete for any rail. Selection advice: the A1 (20 V/V) suits higher-current/lower-shunt designs — for larger signals the A2 (50 V/V), A3 (100 V/V) or A4 (200 V/V) variants reduce shunt dissipation; for 110 V common-mode needs step up to the INA241A. Zero-drift architecture holds accuracy over temperature without calibration. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM358PWR is a Texas Instruments LM358 dual operational amplifier in TSSOP-8 on tape and reel — single supply 3 V to 32 V (or ±1.5 V to ±16 V dual), input common-mode range includes ground, unity-gain stable, two independent op-amps on a 3 × 4.4 mm footprint. The PWR code is the selection point: the same LM358 die as the PDIP-8 LM358P, but in thin-shrink SMD on reel for pick-and-place production — order PWR for volume builds, P for prototypes and hand assembly. Selection advice: the TSSOP-8 footprint is less than a third the board area of PDIP-8, which matters in dense sensor and control boards; electrically the parts are identical, so a design proven on LM358P ports to LM358PWR with only a footprint change. Same caveats as the family: not rail-to-rail output, millivolt offsets — for precision low-voltage work choose a modern RRIO op-amp. Evidence: TI LM358 product page confirms TSSOP-8 availability, 3–32 V single supply and ground-sensing inputs. Match the full LM358PWR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists ADS1115IDGSR as an ACTIVE 16-bit delta-sigma ADC in VSSOP-10, with 860 SPS sampling, 4 multiplexed channels and I2C interface. The 16-bit resolution is the procurement-relevant advantage: it resolves small sensor signals that a 10- or 12-bit converter would bury in quantization noise, which is why this part is the default choice for precision data-acquisition front ends. Selection advice: the IDGSR suffix pins the VSSOP-10 package on tape and reel — the ADS1115 also ships in other packages, so match the full code to your layout. Four multiplexed inputs versus the two-channel ADS1113 and single-ended/differential options are the family decision points; confirm your channel count and interface (I2C here, not SPI) against the datasheet before substituting. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDGST is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter — four single-ended or two differential inputs, programmable gain amplifier with full-scale ranges from ±6.144 V down to ±0.256 V, programmable data rates from 8 to 860 SPS, I2C interface with four pin-selectable addresses, in 10-pin VSSOP, tube packing (DGST), -40 to +125 °C. The integrated PGA, low-drift reference and oscillator are the selection point: true precision ADC performance with no external reference or clock, ideal for battery-voltage monitoring, temperature measurement and portable instrumentation. Selection advice: 860 SPS suits slow precision signals — for kilohertz sampling choose an SAR ADC (ADS868x family) instead. The built-in comparator can drive an alert pin for threshold monitoring without MCU polling, and 16 I2C addresses (four pins × four states) let you run multiple converters on one bus. Note this exact ADS1115IDGST code is the tube variant; IDGSR is the reel version. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA ranges, 8-860 SPS, VSSOP-10 and tube packing. Match the full ADS1115IDGST code for packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDYNR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin SOT-23 package — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing (DYNR), -40 to +125 °C. The SOT-23 footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in the smallest ADS1115 package for space-constrained sensor nodes. Selection advice: same die and performance as the VSSOP (IDGST) and X2QFN (IRUGR) variants — choose this code for the SOT-23 footprint and reel packing. The 150 µA active current and single-shot power-down mode suit battery designs; for 24-bit resolution or excitation sources step up to the ADS1220. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA, I2C, SOT-23-10 and reel packing. Match the full ADS1115IDYNR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin X2QFN package (2 × 1.5 × 0.4 mm) — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing of 3000 (IRUGR; IRUGT is the small reel), -40 to +125 °C. The 2 × 1.5 mm footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in one of the smallest ADC packages available, for wearables and dense sensor boards. Selection advice: same die and performance as the VSSOP (IDGSR) and SOT-23 (IDYNR) variants — choose this code for the X2QFN footprint and 3000-reel packing. Leadless QFN needs reflow assembly and good layout practice; for hand-soldering prototypes choose the VSSOP variant. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D), TI pack addendum and DigiKey listings confirm 16-bit, PGA, I2C, X2QFN-10 and 3000-reel packing. Match the full ADS1115IRUGR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGT is a Texas Instruments 16-bit delta-sigma ADC in 10-pin X2QFN (2.0 × 1.5 × 0.4 mm), 250-piece small reel — I2C interface, four single-ended or two differential inputs, programmable gain amplifier (±256 mV to ±6.144 V), internal low-drift reference and oscillator, programmable comparator, 8 to 860 SPS, 2.0–5.5 V, 150 µA, −40 °C to +125 °C. The integration is the selection point: PGA, MUX, reference, oscillator and comparator on one 2×1.5 mm die means a complete sensor front end with no external analog support chips. Selection advice: the RUG package code is the X2QFN — ADS1115IDGST is the same die in VSSOP-10 on 250-piece small reel — the easier-to-assemble alternative for designs that do not need the 2×1.5 mm X2QFN footprint, not interchangeable on the same footprint. Against the 12-bit ADS1015: pick the ADS1115 for resolution (weighing, precision sensing), the ADS1015 for speed (3300 SPS). The ADDR pin gives four I2C addresses, so up to four devices share one bus. Evidence: TI ADS1115 datasheet (ordering addendum) and distributor listings confirm X2QFN-10, 250-reel, 16-bit, I2C and −40 to +125 °C. Match the full ADS1115IRUGT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.