THVD2450DRBR

SN65HVD3082EDR is a Texas Instruments SN65HVD3082E low-power half-duplex RS-485 transceiver — up to 200 kbps signaling rate, single 5 V supply, 8-pin SOIC, tape-and-reel packing of 2500 (R suffix; EP is the PDIP tube version), -40 to +85 °C. The low power and robustness are the selection point: 0.3 mA typical supply current, 1/8-unit-load input supporting up to 256 nodes on the bus, 15 kV bus-pin ESD protection and fail-safe receiver for open/idle lines. Selection advice: the 3082E is the 200 kbps variant — for 1 Mbps choose SN65HVD3085E or for 20 Mbps SN65HVD3088E, which are pin-compatible upgrades in the same family. This is half-duplex (one driver, one receiver); full-duplex RS-422/485 needs a different device. TI lists this code as Active. Evidence: TI SNx5HVD308xE datasheet (ordering information and package addendum) confirms 200 kbps, SOIC-8, 2500/reel packing and -40 to +85 °C. Match the full SN65HVD3082EDR code for data rate, package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX14783EASA+ is an Analog Devices high-speed RS-485 transceiver in SOIC-8 — for long cable runs where speed and ESD robustness both matter: encoder interfaces, motion controllers and field-bus backplanes. 42 Mbps data rate, ±35kV HBM ESD protection, 3V-to-5.5V supply, hot-swap capability, and true fail-safe receiver. Selection advice: the ASA+ code is the SOIC-8 -40 to +125°C variant — for smaller footprints the ATA+ TDFN-EP is the alternative; against the TI THVD2450 on this site, the MAX14783E trades fault voltage for higher ESD rating — match the protection priority to your installation environment. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX3485ESA+ is a Maxim (Analog Devices) MAX3485 3.3 V half-duplex RS-485/RS-422 transceiver — up to 10 Mbps, one driver plus one receiver, in 8-pin SOIC, tube packing (100 per tube; T suffix is the reel), -40 to +85 °C. The 3.3 V single supply with 5 V-logic interoperability is the selection point: RS-485 on modern 3.3 V logic rails without level translation or charge pumps. Selection advice: the MAX3485 driver is not slew-rate limited, so it reaches 10 Mbps — for EMI-sensitive or long unterminated runs choose the slew-limited MAX3483 (250 kbps) instead. Half-duplex suits two-wire RS-485 buses with up to 32 nodes; for four-wire full-duplex use the MAX3490/91. The fail-safe receiver guarantees a logic-high on open inputs, and driver short-circuit plus thermal shutdown protect the bus. Match the full MAX3485ESA+ code — the + denotes lead-free, ESA is the SO-8 package, and tube versus reel matters for your assembly line. Evidence: Maxim MAX3485 datasheet and TME/LCSC listings confirm 3.3 V, 10 Mbps, half-duplex, SO-8 and -40 to +85 °C. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX485ESA+T is a low-power RS-485/RS-422 transceiver from Analog Devices (Maxim Integrated) in an 8-pin SOIC package, for industrial networks, building automation and long-distance serial links. Its advantage is the RS-485 physical layer itself: differential signaling over twisted pair reaches hundreds of meters and resists industrial noise far better than single-ended UART. Selection advice: the +T denotes the lead-free configuration on tape and reel — match the full code to your compliance and assembly requirements. RS-485 is a half-duplex bus: confirm your network needs biasing and termination resistors at the bus ends, and that only one driver is enabled at a time in your protocol. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot and traceability before quotation and reply within 24 hours.

ST3485ECDR is an STMicroelectronics 3.3 V half-duplex RS-485/RS-422 transceiver in SO-8, tape and reel — guaranteed data rate of at least 12 Mbps, ±15 kV HBM / ±8 kV IEC 61000-4-2 contact ESD, standard 75176 pinout, 1 µA shutdown mode, −7 V to +12 V common-mode range, rated 0 °C to +70 °C. The 3.3 V supply with true 12 Mbps is the selection point: it runs directly from a 3.3 V MCU rail with no level translation, while older 5 V-only transceivers force an extra regulator or translator onto the board. Selection advice: the ECDR code is the commercial-temperature SO-8 reel version — the ST3485EBDR is the −40 °C to +85 °C industrial version in the same SO-8 footprint and a direct drop-in for wider ambient ranges; the ST3485ECN is the DIP-8 tube version for through-hole builds only. ST lists this code Active and shows stock on its official store; DigiKey also lists it as Active and available for ordering. Evidence: the ST official store page and ST3485 datasheet confirm the ordering code, 12 Mbps, ±15 kV ESD, SO-8 reel and Active status. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83848IVVX/NOPB is a Texas Instruments DP83848I industrial-temperature 10/100 Mbps Ethernet PHY transceiver — 48-pin LQFP (7 × 7 mm), MII/RMII/SNI MAC interfaces, auto-MDIX, energy-detect mode, JTAG, 3.3 V, tape-and-reel packing of 1000, -40 to +85 °C. The industrial temperature range is the selection point: the I grade covers factory automation and outdoor equipment where commercial-grade PHYs fail, with auto-MDIX eliminating crossover-cable concerns. Selection advice: this is a PHY only — it needs an external MAC (MCU or switch) and a magnetics module. The V suffix is the 48-LQFP package; NOPB is the lead-free RoHS variant. For Gigabit Ethernet choose a different PHY family, since this is strictly 10/100. TI lists this code as Active. Evidence: TI DP83848I datasheet and distributor listings confirm 10/100 Mbps PHY, 48-LQFP, MII/RMII, -40 to +85 °C and 1000/reel packing. Match the full DP83848IVVX/NOPB code for temperature grade and package. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83867ERGZR is a Texas Instruments 10/100/1000BASE-T Gigabit Ethernet PHY in 48-pin VQFN (7x7mm) — for industrial Ethernet nodes where deterministic latency and diagnostics matter: PLCs, machine vision cameras and grid automation. RGMII and SGMII MAC interfaces, IEEE 1588 start-of-frame detection for time-sensitive networking, cable diagnostics, and 8kV IEC 61000-4-2 ESD protection. Selection advice: the E variant covers -40 to +105°C — for commercial 0 to +70°C the CS code costs less, and the IR code targets -40 to +85°C industrial; for 10/100 Mbps only the DP83848 on this site is the economical choice. 457mW full-power draw suits fanless enclosures. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83TC812RRHARQ1 is a Texas Instruments AEC-Q100 Grade 1 100BASE-T1 automotive Ethernet PHY in 36-pin VQFN (6x6mm) — for zonal E/E architectures replacing CAN with Ethernet: zone controllers, ADAS sensor fusion and infotainment backbones. IEEE 802.3bw compliant, TC-10 sleep/wake under 20µA, integrated low-pass filter passing Level IV emissions, and MII/RMII/RGMII MAC interfaces with 1.8V/2.5V/3.3V I/O. Heat evidence: automotive Ethernet is the fastest-growing in-vehicle networking segment — OEMs are shifting from domain to zonal architectures, and 100BASE-T1 is the volume PHY for camera/radar links. Selection advice: the R variant includes RGMII — for SGMII-only designs the S variant costs less; the integrated LPF eliminates external magnetics filtering. AEC-Q100 Grade 1 (-40 to +125°C) with ±8kV IEC ESD on MDI pins. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS160PR410NJXR is a Texas Instruments quad-channel linear redriver for PCI Express 4.0 (16 Gbps) in 40-pin WQFN (6x4mm), tape and reel — for extending PCIe reach across backplanes and cables in rack servers, HBAs, NICs and hardware accelerators. CTLE boost up to 18 dB at 8 GHz reopens eyes closed by PCB trace loss; protocol-agnostic linear datapaths preserve link-training behavior, with 70 ps typical latency and 60 fs additive jitter. Single 3.3V supply at 124 mW per channel needs no heatsink; pin-strap, SMBus or EEPROM programming covers x2/x4/x8/x16 widths. Selection advice: the NJXR suffix is the WQFN-40 industrial (-40 to +85°C) tape-and-reel orderable — for automotive programs use the DS160PR410-Q1 instead; as a linear (not retimer) redriver it adds no protocol latency, which suits latency-sensitive accelerator fabrics, but for very long reaches evaluate a retimer instead. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ISO1044BD is a Texas Instruments galvanically isolated CAN FD transceiver in SOIC-8 — for CAN buses that cross ground domains: EV battery packs, solar inverters and motor drives where noise currents must not enter the local ground. 5 Mbps CAN FD data rate, ±58V DC bus fault protection, 3000 VRMS isolation barrier, and -40 to +125°C operation. Selection advice: this is the CAN FD generation — for classic CAN isolation the ISO1050 on this site is the established choice; the SOIC-8 D package replaces optocoupler-plus-transceiver discrete solutions in a fraction of the board area. Pair with an isolated power supply for a complete isolated CAN node. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Skyworks and Qorvo expect to close their $22 billion merger on or about October 5, 2026. What the deal changes for RF front-end buyers — and a five-point checklist for before and after close.