LM358PWR

LM358DGKR is a Texas Instruments LM358 dual operational amplifier — the industry-standard general-purpose op-amp, 3 to 32 V single supply (±1.5 to ±16 V dual), internally frequency-compensated, in 8-pin VSSOP, tape-and-reel packing of 2500 (DGKR), 0 to +70 °C commercial grade. Single-supply operation with the common-mode range including ground is the selection point: it runs directly from one 5 V or 3.3 V rail for transducer amplifiers, DC gain blocks and comparator circuits without a negative supply. Selection advice: the output swings to about Vcc - 1.5 V — it is not rail-to-rail, so for full-swing output choose a CMOS rail-to-rail family (TLV or OPA series) instead. This DGKR code is the small VSSOP package on reel; the same die is available in SOIC, TSSOP and PDIP for hand-soldering or legacy layouts. The 0-70 °C range marks it as commercial grade — for industrial or automotive temperature ranges choose the LM2904 family. Evidence: TI LM358 datasheet and distributor listings confirm 3-32 V supply, dual channel, VSSOP-8 and 2500-reel packing. Match the full LM358DGKR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM358P is a Texas Instruments LM358 dual operational amplifier in PDIP-8, tube packaging — single supply 3 V to 32 V (or ±1.5 V to ±16 V dual), input common-mode range includes ground, unity-gain stable, two independent op-amps on one die. The PDIP-8 package is the selection point: through-hole for breadboards, teaching labs, prototyping and legacy repairs — the same LM358 die ships in SOIC, TSSOP and VSSOP under different suffixes, so match the full LM358P code to your board. Selection advice: the ground-sensing input of the LM358 is why it survives in single-supply sensor front ends where older op-amps cannot swing low enough — pick it for comparators, active filters and transducer amplifiers on a single rail. It is not rail-to-rail output and not precision (millivolt offsets), so for low-voltage precision work step up to a modern RRIO part. As the most remarked jellybean op-amp in the market, require lot traceability. Evidence: TI LM358 product page confirms PDIP-8, 3–32 V single supply and ground-sensing inputs. Match the full LM358P code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

INA240A1PWR is a Texas Instruments bidirectional current-sense amplifier with enhanced PWM rejection — for in-line motor phase current and power-rail telemetry where switching noise corrupts ordinary sensing: -4 V to 80 V common-mode range, 20 V/V fixed gain (A1), ±25 µV max offset, 132 dB DC CMRR, in 8-pin TSSOP, -40°C to +125°C. The enhanced PWM rejection suppresses large common-mode transients without output ripple, enabling accurate current measurement directly in the switching path — the same telemetry function datacenter PMBus modules integrate, here as a discrete for any rail. Selection advice: the A1 (20 V/V) suits higher-current/lower-shunt designs — for larger signals the A2 (50 V/V), A3 (100 V/V) or A4 (200 V/V) variants reduce shunt dissipation; for 110 V common-mode needs step up to the INA241A. Zero-drift architecture holds accuracy over temperature without calibration. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TL072CPWR is a Texas Instruments TL072 dual JFET-input operational amplifier in TSSOP-8, 2000-piece tape and reel — 3 MHz gain-bandwidth, 13 V per microsecond slew rate, JFET inputs with picoamp bias current, common-mode range includes VCC+, 1.4 mA per channel, commercial 0 °C to 70 °C grade. The CPWR code is the selection point: the commercial-grade die in the smallest TSSOP-8 footprint on reel for high-volume SMD production — prototypes use the PDIP tube codes. Selection advice: the JFET input is why the TL072 owns audio preamp and high-impedance sensor sockets — source impedances in the hundreds of kilohms see essentially no bias-current error, where a bipolar op-amp would. The C grade (0 to 70 °C) suits consumer and indoor industrial gear; for extended temperature pick the I-grade TL072IDR/TL072IP (−40 to +85 °C). Not rail-to-rail output, so for low-voltage single-supply work choose a modern RRIO part. Evidence: TI TL072 datasheet ordering information confirms TSSOP-8 (PW), 2000-piece reel and the C-grade temperature range. Match the full TL072CPWR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists ADS1115IDGSR as an ACTIVE 16-bit delta-sigma ADC in VSSOP-10, with 860 SPS sampling, 4 multiplexed channels and I2C interface. The 16-bit resolution is the procurement-relevant advantage: it resolves small sensor signals that a 10- or 12-bit converter would bury in quantization noise, which is why this part is the default choice for precision data-acquisition front ends. Selection advice: the IDGSR suffix pins the VSSOP-10 package on tape and reel — the ADS1115 also ships in other packages, so match the full code to your layout. Four multiplexed inputs versus the two-channel ADS1113 and single-ended/differential options are the family decision points; confirm your channel count and interface (I2C here, not SPI) against the datasheet before substituting. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDGST is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter — four single-ended or two differential inputs, programmable gain amplifier with full-scale ranges from ±6.144 V down to ±0.256 V, programmable data rates from 8 to 860 SPS, I2C interface with four pin-selectable addresses, in 10-pin VSSOP, tube packing (DGST), -40 to +125 °C. The integrated PGA, low-drift reference and oscillator are the selection point: true precision ADC performance with no external reference or clock, ideal for battery-voltage monitoring, temperature measurement and portable instrumentation. Selection advice: 860 SPS suits slow precision signals — for kilohertz sampling choose an SAR ADC (ADS868x family) instead. The built-in comparator can drive an alert pin for threshold monitoring without MCU polling, and 16 I2C addresses (four pins × four states) let you run multiple converters on one bus. Note this exact ADS1115IDGST code is the tube variant; IDGSR is the reel version. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA ranges, 8-860 SPS, VSSOP-10 and tube packing. Match the full ADS1115IDGST code for packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDYNR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin SOT-23 package — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing (DYNR), -40 to +125 °C. The SOT-23 footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in the smallest ADS1115 package for space-constrained sensor nodes. Selection advice: same die and performance as the VSSOP (IDGST) and X2QFN (IRUGR) variants — choose this code for the SOT-23 footprint and reel packing. The 150 µA active current and single-shot power-down mode suit battery designs; for 24-bit resolution or excitation sources step up to the ADS1220. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA, I2C, SOT-23-10 and reel packing. Match the full ADS1115IDYNR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin X2QFN package (2 × 1.5 × 0.4 mm) — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing of 3000 (IRUGR; IRUGT is the small reel), -40 to +125 °C. The 2 × 1.5 mm footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in one of the smallest ADC packages available, for wearables and dense sensor boards. Selection advice: same die and performance as the VSSOP (IDGSR) and SOT-23 (IDYNR) variants — choose this code for the X2QFN footprint and 3000-reel packing. Leadless QFN needs reflow assembly and good layout practice; for hand-soldering prototypes choose the VSSOP variant. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D), TI pack addendum and DigiKey listings confirm 16-bit, PGA, I2C, X2QFN-10 and 3000-reel packing. Match the full ADS1115IRUGR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGT is a Texas Instruments 16-bit delta-sigma ADC in 10-pin X2QFN (2.0 × 1.5 × 0.4 mm), 250-piece small reel — I2C interface, four single-ended or two differential inputs, programmable gain amplifier (±256 mV to ±6.144 V), internal low-drift reference and oscillator, programmable comparator, 8 to 860 SPS, 2.0–5.5 V, 150 µA, −40 °C to +125 °C. The integration is the selection point: PGA, MUX, reference, oscillator and comparator on one 2×1.5 mm die means a complete sensor front end with no external analog support chips. Selection advice: the RUG package code is the X2QFN — ADS1115IDGST is the same die in VSSOP-10 on 250-piece small reel — the easier-to-assemble alternative for designs that do not need the 2×1.5 mm X2QFN footprint, not interchangeable on the same footprint. Against the 12-bit ADS1015: pick the ADS1115 for resolution (weighing, precision sensing), the ADS1015 for speed (3300 SPS). The ADDR pin gives four I2C addresses, so up to four devices share one bus. Evidence: TI ADS1115 datasheet (ordering addendum) and distributor listings confirm X2QFN-10, 250-reel, 16-bit, I2C and −40 to +125 °C. Match the full ADS1115IRUGT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1220IPW is a Texas Instruments ADS1220 24-bit delta-sigma analog-to-digital converter for small-signal sensors — programmable gain from 1 to 128 V/V, up to 2000 SPS with single-cycle settling, SPI-compatible interface, in 16-pin TSSOP, tube packing (IPW; IPWR is the reel version), -40 to +125 °C. The two programmable excitation current sources plus simultaneous 50/60 Hz rejection at 20 SPS are the selection point: complete RTD, thermocouple, bridge-sensor and weigh-scale front ends with no external current source or mains-noise filtering. Selection advice: 20-bit effective resolution suits precision instrumentation — for kilohertz sampling choose an SAR ADC instead. The internal 2.048 V reference, oscillator and temperature sensor cut the external BOM to near zero; for I2C instead of SPI choose the ADS1115 family. TI lists this code as Active. Evidence: TI ADS1220 datasheet (SBAS501D) and TI pack addendum confirm 24-bit, PGA 1-128, 2 kSPS, TSSOP-16 and tube packing. Match the full ADS1220IPW code for packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.