74HC138D,653

74HC595D,118 is a Nexperia 8-bit shift register with output latch and 3-state outputs in SO-16, reel — for expanding MCU outputs: LED matrices, relay banks and 7-segment displays. Three pins driving unlimited cascaded outputs is the selection point: GPIO expansion at cents per pin. Selection advice: the D,118 suffix denotes SO-16 in reel for production — a second source to TI's SN74HC595D for supply resilience; verify logic thresholds match your design if mixing vendors. For tighter spaces, the TSSOP PW,118 variant shrinks the footprint. Parameters verified against the Nexperia official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

74AVC9112DCH is a 1:4 clock fanout buffer from Nexperia in VSSOP-8 — for distributing one clock to four loads with low skew in digital systems. The 1:4 fanout is the selection point: one device replaces four discrete buffers, keeping clock edges aligned across loads. Selection advice: the AVC family runs at low voltage for modern logic levels — confirm your clock voltage and frequency fit the device ratings before committing. The DCH suffix denotes VSSOP-8. For more outputs, look at larger fanout buffers in the same family. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

74HC04D,653 is a Nexperia hex inverter in SO-14 — for basic logic inversion: signal polarity fixes, clock inversion and simple glue logic. Six inverters in one package is the selection point: a low-cost way to fix polarity mistakes on a finished board. Selection advice: the D,653 suffix denotes SO-14 — pick the 74HC04 for plain inversion; when the input is slow or noisy, the Schmitt-trigger 74HC14 is the safer choice. 2.0–6.0 V supply covers most logic designs. Nexperia lists this part as Active. Parameters verified against the Nexperia official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

74HC08D,653 is a Nexperia quad 2-input AND gate in SO-14 — for basic combinational logic: gating clocks, combining enables and simple glue logic. Four AND gates with 7 ns propagation delay is the selection point: fast-enough combining logic at the lowest cost. Selection advice: the D,653 suffix denotes SO-14 — pick the 74HC08 for plain AND logic; for wider functions in one package, consider multi-function gates. 2.0–6.0 V supply covers most logic designs. Nexperia lists this part as Active. Parameters verified against the Nexperia official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

74HC14D,653 is a Nexperia hex inverting Schmitt trigger in SO-14 — for cleaning up noisy signals: button debouncing, slow-edge squaring and simple oscillators. The Schmitt hysteresis is the selection point: reliable switching on slow or noisy inputs where plain inverters chatter. Selection advice: the D,653 suffix denotes SO-14 — pick the 74HC14 for debouncing and signal conditioning; one gate plus an RC makes a simple clock oscillator. For non-inverting hysteresis, the 74HC14's sibling 74HC7014 (where available) is the alternative. Nexperia lists this part as Active. Parameters verified against the Nexperia official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

74HC574PW is an octal D-type flip-flop with 3-state outputs in 20-pin TSSOP — positive-edge triggered, 8-bit register with a common output-enable, supply 2.0 V to 6.0 V, rated −40 °C to +125 °C. The octal register with 3-state outputs is the selection point: eight data bits latch on one clock edge and release to the bus only when enabled, which is the standard pattern for bus interfacing, LED/relay drive and address latching in 74-series glue logic. Selection advice: Nexperia is the current manufacturer (the NXP standard-logic line became Nexperia in 2017) — the full orderable code is 74HC574PW,112 where ,112 is the packing code; for TTL-level inputs choose the 74HCT574PW, for SO-20 assembly choose the 74HC574D. Nexperia does not show an explicit lifecycle status on the product page; distributors including Farnell currently list stock available for ordering. Evidence: the Nexperia product page and distributor listings confirm the type number, TSSOP-20 package, 2.0–6.0 V range and orderable code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

74HC595PW,118 is a Nexperia PRODUCTION 8-bit serial-in, serial or parallel-out shift register with output latches and 3-state outputs in TSSOP-16 — for expanding MCU outputs in tight spaces: LED matrices, relay banks and display drivers. Three pins driving unlimited cascaded outputs is the selection point: GPIO expansion at cents per pin. Selection advice: the PW,118 suffix denotes TSSOP-16 — the compact variant of the SO-16 D,118; 2.0 V to 6.0 V supply and up to 108 MHz clock cover most logic designs. A second source to TI's SN74HC595PW for supply resilience. Parameters verified against the Nexperia official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

74HC74D,653 is a Nexperia dual D-type flip-flop with set and reset, positive-edge triggered, in SO-14 — for divide-by-two counters, data synchronization and toggle circuits. Independent set/reset on each flip-flop is the selection point: flexible state control without extra gates. Selection advice: the D,653 suffix denotes SO-14 — pick the 74HC74 for classic dual flip-flop duty; for single-gate fixes, the 1G/2G little-logic families save board space. 82 MHz max frequency covers most glue-logic clocking. Nexperia lists this part as Active. Parameters verified against the Nexperia official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

74HC595S16-13 is a Diodes Incorporated 8-bit shift register with 8-bit output register in SO-16, 13-inch tape and reel — for expanding MCU outputs: LED matrices, relay banks and 7-segment displays. Three pins driving unlimited cascaded outputs is the selection point: GPIO expansion at cents per pin. Selection advice: the S16-13 suffix denotes SO-16 on 13-inch reel for production — a second source to TI's SN74HC595D and Nexperia's 74HC595D for supply resilience; 2.0 V to 6.0 V supply with push-pull outputs covers most logic designs. Parameters verified against the Diodes official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L6390DTR is an ST half-bridge gate driver — SO-16, 600 V high-side rail, 290 mA source / 430 mA sink, 50 V/ns dV/dt immunity, UVLO, tape and reel. The 50 V/ns dV/dt immunity is the selection point: robust half-bridge drive for fast-switching MOSFETs where high dv/dt causes false triggering in weaker drivers. Selection advice: ST lists the L6390DTR as Active. The DTR suffix denotes SO-16 on tape and reel — match it to your footprint. Verify the 290 mA/430 mA drive against your MOSFET gate charge at the switching frequency — for larger switches step up to a higher-current driver. Evidence: ST data confirms Active, SO-16, 600 V rail, drive currents, 50 V/ns immunity. Match the full L6390DTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.