INA219AIDR

INA219BIDR is a Texas Instruments B-grade zero-drift bidirectional current/power monitor in SOIC-8, 3000-piece large reel — 0.5% maximum accuracy over temperature (B grade), 0–26 V bus sensing, 3–5.5 V supply, 12-bit ADC with programmable averaging to 128 samples, calibration register for direct ampere and watt readouts, 16 programmable I2C addresses, −40 °C to +125 °C. The SOIC-8 package is the selection point: the same B-grade 0.5% die as the SOT-23 variants, but in a package that hand-solders and reworks comfortably — a real advantage for repair, rework and low-cost assembly flows. Selection advice: the D code is SOIC-8 — not footprint-compatible with the SOT-23-8 INA219BIDCNR/IDCNT, so pick the package before the PCB is taped out. The R suffix is the 3000-piece reel for volume; for small runs the SOT-23 T-reel variant is the economical prototype path. Evidence: TI INA219 datasheet (Rev. G) confirms B-grade 0.5%, SOIC-8 and the 3000-reel option. Match the full INA219BIDR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

INA219AIDCNT is a Texas Instruments INA219 zero-drift, bidirectional current and power monitor with I2C interface — senses bus voltages from 0 to 26 V, reports current, voltage and power directly in amperes and watts through calibration and multiplier registers, in 8-pin SOT-23, tube packing (DCNT), -40 to +125 °C. Direct digital readouts are the selection point: no analog signal chain or ADC math in firmware — the MCU reads current and power over I2C for servers, telecom, battery chargers and power-supply telemetry. Selection advice: this is the A grade; the B grade (INA219B) tightens accuracy to 0.5% over temperature for precision billing or calibration use. Sixteen programmable I2C addresses allow many monitors on one bus; for analog-output monitoring at lower cost consider the INA210-INA214 family instead. Note DCNT is the tube variant; DCNR is the reel version. Evidence: TI INA219 datasheet (SBOS448G) and distributor listings confirm 0-26 V sensing, I2C, SOT-23-8 and tube packing. Match the full INA219AIDCNT code for grade and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

INA219BIDCNR is a Texas Instruments B-grade zero-drift bidirectional current/power monitor in SOT-23-8, 3000-piece large reel — 0.5% maximum accuracy over temperature (B grade), 0–26 V bus sensing, 3–5.5 V supply, 12-bit ADC with programmable averaging to 128 samples, calibration register for direct ampere and watt readouts, 16 programmable I2C addresses, −40 °C to +125 °C. The B grade is the selection point: 0.5% maximum accuracy versus 1% on the A grade — for power-rail monitoring and battery gauging where the error budget is tight, the B grade earns its premium. Selection advice: the DCN code is SOT-23-8 — INA219BIDR is the same B-grade die in SOIC-8, not footprint-compatible. The R suffix is the 3000-piece reel; INA219BIDCNT is the identical part on 250-piece reel for prototypes. Size the shunt for your current range and write the calibration register once — current and power then read out directly. Evidence: TI INA219 datasheet (Rev. G) confirms B-grade 0.5%, SOT-23-8, 0–26 V and the 3000-reel option. Match the full INA219BIDCNR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

INA219BIDCNT is a Texas Instruments B-grade zero-drift bidirectional current/power monitor in SOT-23-8, 250-piece small reel — 0.5% maximum accuracy over temperature (B grade), 0–26 V bus sensing, 3–5.5 V supply, 12-bit ADC with programmable averaging to 128 samples, calibration register for direct ampere and watt readouts, 16 programmable I2C addresses, −40 °C to +125 °C. The small reel is the selection point: the identical B-grade die and SOT-23-8 package as INA219BIDCNR, but on 250-piece reel — prototypes, pilot runs and low-volume repairs get the tighter 0.5% grade without committing to a 3000-piece reel. Selection advice: T versus R is purely a packing choice — same silicon, same SOT-23-8 footprint, so a design qualified on the T reel moves to the R reel for volume with no requalification. Do not confuse with the A grade (1% accuracy) or the SOIC-8 INA219BIDR. Evidence: TI INA219 datasheet (Rev. G) confirms B-grade 0.5%, SOT-23-8 and the 250-reel option. Match the full INA219BIDCNT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AMC1350DWVR is a Texas Instruments isolated amplifier in 8-pin SOIC — for precision voltage sensing across isolation barriers: reinforced isolation with ±5V input range, optimized for AC voltage measurement in motor drives, solar inverters and power supplies where the high-voltage side must be galvanically separated from the control side. The DWVR code is the SOIC-8 reel variant with 1000-unit reel. Selection advice: the AMC1350 targets AC voltage sensing (±5V input) — for DC shunt-based current sensing the AMC1301 family is the companion choice; for designs needing an integrated DC/DC converter to power the high side, the AMC3330 eliminates the external isolated supply. Against non-isolated precision amps on this site, the isolation barrier is the differentiator — do not substitute a non-isolated amp where safety isolation is required. Heat evidence: listed in Octopart Linear ICs Popular Parts (octopart.com, verified 2026-10-09); TI E2E forum shows active customer evaluation for high-voltage measurement. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TI lists INA219AID as OBSOLETE — a 26 V, 12-bit I2C digital power monitor in 8-pin SOIC-8 (D) tube, for bidirectional current and power measurement with 0–26 V common-mode range and programmable gain. Important for procurement: only this tube-packing ordering code is obsolete — TI confirms the tape-and-reel variant INA219AIDR remains active, so if your assembly can take reel packing, qualify INA219AIDR as the drop-in replacement rather than chasing obsolete tube stock. Selection advice: for repairs and last-time builds of the AID code, send quantity and date-code requirements with your RFQ and we will check what can still be sourced with traceability; for new designs, specify INA219AIDR or a current-generation power monitor. Parameters verified against the TI official product page. We reconfirm the offered lot before quotation and reply within 24 hours.

The INA240A1EDRQ1 is an AEC-Q100 automotive bidirectional current-sense amplifier in 8-pin SOIC. It senses shunt drops over a -4 V to 80 V common-mode range independent of supply voltage, so it handles high-side, low-side and below-ground flyback transients in motor drives and solenoid controls. Enhanced PWM rejection suppresses large common-mode transients without output ripple, giving accurate current readings in PWM systems and cutting calibration and rework cost. Precision is guaranteed by +/-25 uV maximum offset, 250 nV per degC maximum offset drift, 0.2 percent maximum gain error and 2.5 ppm per degC maximum gain drift, with 132 dB DC CMRR and 400 kHz bandwidth. It runs from a single 2.7 V to 5.5 V supply at 2.4 mA maximum, is specified from -40C to +150C, and is functional safety-capable for ASIL system designs. Selection advice: the A1 suffix fixes gain at 20 V/V; if your ADC range calls for 50, 100 or 200 V/V, order the A2, A3 or A4 variants instead of resizing the shunt, because gain is factory-trimmed and not field adjustable. Ranked on hqbuy.com real-time hot list (2026-10-14). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM2903DR is a Texas Instruments dual differential comparator in SOIC-8 — for industrial threshold detection: the extended-temperature sibling of the LM393. 2–30 V single supply (±1–15 V dual), 1.3 µs response, open-collector outputs, -40°C to +125°C operation. Heat evidence: the comparator market grows from $7.69B to $8.23B (2026 report) — the LM393/LM2903 family remains a permanent distributor staple with multi-thousand-piece stock. Selection advice: the DR suffix is SOIC-8 on reel — the LM2903 is the -40 to +125°C version of the LM393 (0 to 70°C); same footprint, do not mix temperature grades on automotive BOMs. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM293DR is a Texas Instruments dual differential comparator in SOIC-8 — for threshold detection and signal conditioning: 2–36 V supply, open-collector outputs, -25°C to +85°C commercial grade. Selection advice: the DR code is SOIC-8 on reel — the LM293 is the commercial-grade counterpart to the automotive LM2903; for wider temperature range use the LM2903. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM358DR is a dual general-purpose operational amplifier from Texas Instruments in an 8-pin SOIC package — for signal conditioning, active filters and comparator-with-hysteresis circuits. The single-supply operation down to 3 V is the selection point: it runs directly from the same rail as 3.3 V and 5 V logic, which is why the LM358 remains the default jelly-bean op-amp. Selection advice: the DR suffix denotes SOIC-8 on tape and reel — the LM358 ships in PDIP-8 and other packages, so match the full LM358DR code to your footprint. For new precision designs, compare against newer low-offset op-amps; for cost-driven general-purpose use, this is the part. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.