MAX5815AWC+T

DAC161S997RGHR is a Texas Instruments 16-bit delta-sigma DAC for 4-20 mA current-loop transmission, SPI interface, 2.7 to 3.6 V supply, in WQFN-16 (4 × 4 mm) — the loop-powered transmitter chip for industrial 2-wire and 4-wire field instruments. The 100 µA total supply current is the selection point: in a loop-powered transmitter the DAC must sip from the 4 mA budget, leaving the rest for the sensor and MCU. Selection advice: this is a 4-20 mA loop transmitter, not a general voltage-output DAC — the output stage drives an external bipolar transistor (e.g. 2N3904) per the TI reference design, so verify the loop compliance and error-level programming (3.375 mA / 21.75 mA defaults) against your system FMEA. HART modulator interfacing is built in for smart-transmitter designs. The RGH suffix is the WQFN-16 package, R = tape and reel (4500). Parameters verified against the TI DAC161S997 datasheet (SNAS621) and Mouser listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DAC8812IBPWR is a Texas Instruments dual 16-bit current-output multiplying DAC in TSSOP-16, tape and reel — 1 LSB maximum relative accuracy and differential nonlinearity, 2 mA full-scale current, 0.5 µs settling time, 50 MHz SPI-compatible 3-wire interface, double-buffered registers for simultaneous dual-channel updates, internal power-on reset, single 2.7 V to 5.5 V supply, rated −40 °C to +85 °C. The multiplying architecture is the selection point: the output scales with the reference, so it works as a digitally controlled attenuator or programmable gain element — a straight voltage-output DAC cannot do that job. Selection advice: IBPWR is the B-grade TSSOP reel version (2,000 per reel) — the DAC8812IBPW is the tube twin, the DAC8812ICPWR the C-grade (one accuracy step down) reel version; the DAC8811 is the single-channel and DAC8814 the quad-channel family member for different channel counts. TI lists this code Active; LCSC lists it as in stock and Rochester Electronics marks the manufacturer life cycle Active. Evidence: the TI DAC8812 packaging addendum (10-Nov-2025) confirms the ordering code, 16-bit dual multiplying architecture, TSSOP-16 reel and Active status. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP4725A0T-E/CH is a Microchip 12-bit single-channel digital-to-analog converter with on-board EEPROM, I2C interface, buffered rail-to-rail output, in SOT-23-6, 2.7 to 5.5 V supply, -40 to +125 °C. The EEPROM is the selection point: the DAC powers up to the stored output code without MCU initialization, which is exactly what set-and-forget control outputs — bias trims, threshold references, drive levels — need to survive power cycles. Performance facts that matter for procurement: 6 µs settling, ±0.2 LSB DNL, 210 µA supply current, and I2C up to 3.4 MHz. Selection advice: the A0 in the code is the external address pin, so multiple MCP4725 variants with different address options can share one I2C bus — confirm the address option against your bus map before ordering, and choose this EEPROM version over plain DACs only when power-on recall is genuinely required, since it costs more than a volatile-output equivalent. Distributor listings mark this ordering code AEC-Q100, useful for automotive-adjacent programs. Evidence: Microchip datasheet and Farnell/element14 listings confirm 12-bit, I2C, EEPROM, SOT-23-6 and 2.7-5.5 V. Match the full MCP4725A0T-E/CH code for the address option and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

PCM5102A is a Texas Instruments 112-dB SNR stereo audio DAC in 20-pin TSSOP — for network streamers, USB DACs and smart-speaker line outputs where clean analog must come from I2S with minimal support circuitry: 32-bit, up to 384-kHz sampling, integrated PLL generates the system clock from BCLK (3-wire I2S, no MCLK), and DirectPath 2.1-VRMS ground-centered outputs eliminate DC-blocking capacitors. Selection advice: the hardware-pin-controlled A variant suits fixed-function designs — for software-controlled filtering choose the PCM5122; against the automotive PCM5102A-Q1 on this site, the catalog grade covers -25 to +85C commercial/industrial use. Up to 20-dB lower out-of-band noise than conventional switched-capacitor DACs eases downstream amplifier/ADC filtering. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TLV320AIC3104-Q1 is a Texas Instruments automotive stereo audio codec in 32-pin VQFN — for infotainment head units, telematics and e-call where AEC-Q100 qualification is mandatory: stereo 92-dB ADC plus 102-dB DAC, 6 analog inputs and 6 outputs, stereo headphone amplifier, I2C control with I2S/DSP/TDM audio interface. The record path integrates microphone bias, programmable PGA and AGC with mix/mux across inputs; the playback path routes DAC and selected inputs through volume controls to the outputs. Selection advice: this is the automotive grade of the catalog TLV320AIC3104 — for non-automotive portable audio the catalog grade costs less; for higher 105-dB ADC performance the TAC5112-Q1 is TI newer generation. 14-mW stereo 48-kHz DAC playback from 3.3 V suits always-on voice pickup paths. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD4003BRMZ is an Analog Devices 18-bit, 2 MSPS successive-approximation ADC in 10-lead MSOP — for precision data acquisition that needs both speed and DC accuracy: automatic test equipment, portable instruments and machine automation. ±1 LSB maximum INL with 100.5 dB SNR and -123 dB THD at 1 kHz, no latency or pipeline delay with first conversion accurate, and a high-Z input mode plus long acquisition phase that lets low-power precision amplifiers drive it directly — no dedicated high-speed ADC driver required. Input span compression runs the driver and ADC from common rails without a negative supply. Selection advice: the BRMZ code is the MSOP-10 version — for 16-bit at lower cost the AD4000 is the family sibling; the 1.8 V single supply with 1.71–5.5 V logic interface suits battery-powered field instruments. Daisy-chainable SPI simplifies multichannel layouts. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD5689RBRUZ is an Analog Devices dual 16-bit buffered voltage-output DAC in 16-lead TSSOP — for precision setpoint and calibration outputs in industrial control: PLC I/O cards, data acquisition and optical transceiver biasing. ±2 LSB maximum INL at 16 bits, an internal 2.5 V reference with 2 ppm/°C typical drift (no external reference needed), user-selectable gain of 1 or 2 for 2.5 V or 5 V full scale, 20 mA drive capability within 0.5 V of the rails, and 50 MHz SPI with daisy-chain and readback. Power-on reset to zero or midscale keeps outputs safe at startup. Selection advice: the BRUZ code is the TSSOP-16 tube version — for single-channel designs the AD5683R is the family sibling; against the octal DAC80508 on this site, the AD5689R is the pick for dual-channel precision nodes where per-channel accuracy matters more than channel count. The 4 µA power-down mode suits battery-backed calibration circuits. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD5761RARUZ is an Analog Devices 16-bit voltage-output DAC with integrated 2.5V reference in TSSOP-16 — for industrial automation outputs where one chip must cover every standard range: PLC analog outputs, servo control and process control. Eight software-programmable output ranges (0-5V, 0-10V, 0-20V, ±3V, ±5V, ±10V and more) with 5% overrange, a ±2ppm/°C drift reference and ±2-LSB maximum INL mean the output stays accurate without external trimming. Selection advice: the ARUZ code is the TSSOP-16 reel variant — for the smaller 3x3mm LFCSP specify the ACPZ; the AD5721R is the 12-bit cost-down sibling. Single-supply 4.75V-to-30V or dual-supply operation covers both unipolar and bipolar systems — confirm your supply configuration against the range table. Asynchronous LDAC and reset-to-zero/midscale suit safety-critical outputs. Parameters verified against Analog Devices documentation and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620ARZ is a low-power instrumentation amplifier from Analog Devices in an 8-pin SOIC package, with gain set by a single external resistor — for bridge sensors, strain gauges and other small differential signals. Its advantage is the classic three-op-amp instrumentation topology in one package: high common-mode rejection with minimal external circuitry, which shortens precision front-end design. Selection advice: the ARZ suffix denotes the standard grade in SOIC-8 on tape and reel — the AD620 also ships in DIP and higher grades, so match the full code to your footprint and accuracy requirements. Gain is set by one resistor value, so confirm your gain calculation against the datasheet formula during design. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD623ARZ-R7 is an Analog Devices single-supply instrumentation amplifier, rail-to-rail output, gain 1 to 1000 set by one external resistor, 800 kHz bandwidth at G=1, in SOIC-8 — the sensor front-end amplifier for bridges, thermocouples and low-level transducer signals. The single-resistor gain programming is the selection point: no matched resistor networks to source, with 0.10% gain accuracy at G=1, 200 µV max offset and 550 µA max supply current for battery-powered instruments. Selection advice: it runs on 3 to 12 V single supply or ±2.5 to ±6 V dual supply — but note the input range extends only 150 mV below ground on a single rail, so ground-referenced bipolar sensor signals still need the dual-supply configuration. The R7 suffix is the 7-inch reel (1000 pcs) packing of the SOIC-8. For higher precision or lower noise, compare the AD620/AD8221 family rather than assuming drop-in equivalence. Parameters verified against the ADI AD623 datasheet and Mouser/LCSC listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.