UCC27712DR

onsemi lists FAN7382MX as Active — a 625 V high/low-side gate driver for MOSFET/IGBT in SOIC-8, TTL-input compatible, 0.35 A source / 0.65 A sink, VCC max 25 V, tape and reel. The 625 V rating with TTL-compatible inputs is the selection point: it drives high-side MOSFETs/IGBTs in offline converters directly from logic signals, without level-shifting circuitry. Selection advice: the MX suffix denotes SOIC-8 on tape and reel — match the full code to your layout. Confirm your bus voltage against the 625 V rating with derating, and verify the drive current against your MOSFET gate charge at your switching frequency. Parameters verified against the onsemi official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

INA240A1QDRQ1 is a Texas Instruments automotive high-side current sense amplifier with enhanced PWM rejection in SOIC-8, tape and reel — for motor phase-current sensing and solenoid monitoring in automotive drives. The PWM rejection is the selection point: accurate current measurement riding on fast-switching inverter outputs where ordinary amplifiers saturate. Selection advice: the Q1 suffix denotes the automotive-qualified variant — mandatory for automotive programs; the gain variant A1 sets the fixed gain — match it to your shunt and ADC range. For industrial-only designs, the non-Q1 INA240 is the alternative. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists LM393DR as an ACTIVE dual differential comparator with open-collector outputs in SOIC-8, with 2 V to 36 V supply range. The open-collector output is the design-relevant detail: it allows wired-OR logic and level translation to a different supply rail with a single pull-up resistor, which push-pull comparators cannot do. Selection advice: the DR suffix denotes SOIC-8 on tape and reel — the LM393 ships in several packages, so match the full code to your footprint. A comparator is not an op-amp: confirm your circuit uses it for threshold detection rather than linear amplification before substituting. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM5109AMAX/NOPB is a Texas Instruments 1 A peak half-bridge gate driver in SOIC-8, tape and reel — for compact half-bridge stages: DC/DC, motor drives and inverters. 100 V bootstrap drive in a standard SOIC-8 is the selection point: high-voltage half-bridge in the industry's most common package. Selection advice: the MAX/NOPB denotes SOIC-8 in tape and reel for production — the easy-to-source package for prototypes through production; for higher drive current, the LM5105 family is the step up. 8 V to 14 V supply with 7 V UVLO. TI lists this part as ACTIVE. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM5109MAX/NOPB is a Texas Instruments 100 V 1 A/1 A peak half-bridge gate driver with 7 V UVLO in SOIC-8, tape and reel — for compact half-bridge stages: DC/DC, motor drives and inverters. 100 V bootstrap drive in a standard SOIC-8 is the selection point: high-voltage half-bridge in the industry's most common package. Selection advice: the MAX/NOPB denotes SOIC-8 in tape and reel for production — the easy-to-source package for prototypes through production; the A variant (LM5109AMAX/NOPB) tightens specifications, so verify which your design was qualified with. 8 V to 14 V supply with 7 V UVLO. TI lists this part as ACTIVE. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM5164DDAR is a Texas Instruments 100 V input synchronous buck converter in SOIC-8, tape and reel — for industrial power supplies: 48 V bus step-down, PoE front ends and motor-drive auxiliaries. The 100 V input rating is the selection point: direct operation from high-voltage industrial buses that standard 60 V bucks cannot survive. Selection advice: the DDAR suffix denotes SOIC-8 in tape and reel for production — plan the external MOSFET, inductor and compensation network per TI's reference design; this is a controller-class part, not a module. For lower-voltage rails, cheaper integrated bucks save board space. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN65HVD230D is a Texas Instruments 3.3 V CAN transceiver — standby mode via pin 8, SOIC-8, up to 1 Mbps, −40 to +85 °C. The 3.3 V supply is the selection point: direct interfacing to 3.3 V MCUs with no 5 V rail — the classic CAN node for 3.3 V systems. Selection advice: lifecycle warning — TI has discontinued the SN65HVD230D ("no longer in production"); for new designs use the pin-compatible SN65HVD230 (the non-D variant) or a current 3.3 V CAN transceiver, and for repairs and legacy builds we source remaining distributor stock. Match the full SN65HVD230D code — the SN65HVD230 without D is the recommended replacement, not an identical part. Evidence: TI data confirms discontinued status, 3.3 V CAN, standby mode, SOIC-8, 1 Mbps. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN65HVD231D is a Texas Instruments 3.3 V CAN transceiver with sleep mode in SOIC-8 — for CAN nodes in automotive and industrial networks. 1 Mbps per ISO 11898-2 is the selection point: standard CAN physical layer from a 3.3 V supply. Lifecycle note: TI lists the SN65HVD231 as obsolete ("no longer in production") — for new designs, migrate to a current-production 3.3 V CAN transceiver such as the TCAN33x family; for repairs and legacy builds, we source remaining stock. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN65HVD232D is a Texas Instruments 3.3 V CAN transceiver with standby mode in SOIC-8 — for CAN nodes in automotive and industrial networks. 1 Mbps per ISO 11898-2 is the selection point: standard CAN physical layer from a 3.3 V supply. Lifecycle note: TI lists the SN65HVD232 as obsolete ("no longer in production") — for new designs, migrate to a current-production 3.3 V CAN transceiver such as the TCAN33x family; for repairs and legacy builds, we source remaining stock. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN65HVD233D is a Texas Instruments 3.3 V CAN transceiver with standby and loopback in SOIC-8 — for CAN nodes in automotive and industrial networks. 1 Mbps per ISO 11898-2 with ±36 V bus-fault protection is the selection point: robust CAN physical layer from a 3.3 V supply. Lifecycle note: TI lists the SN65HVD233 as discontinued ("no longer in production") — for new designs, migrate to a current-production 3.3 V CAN transceiver such as the TCAN33x family; for repairs and legacy builds, we source remaining stock. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.