ADS7846

TSC2007 is a Texas Instruments nanopower 4-wire resistive touch screen controller in 16-pin TSSOP — for battery-powered handhelds where every microamp matters: portable instruments, point-of-sale terminals and GPS units. 8- or 12-bit programmable resolution, I2C interface with standard/fast/high-speed modes, 1.2 V to 3.6 V single supply, on-chip temperature and touch-pressure measurement, and preprocessing that filters touch data before it hits the bus. The nanopower operation is the selection point: tens of microamps at typical conversion rates means the touch subsystem barely registers on the battery budget, and the preprocessing offloads the host MCU from raw-sample filtering. Selection advice: the I2C interface suits pin-constrained designs — for SPI hosts the TSC2046 on this site is the alternative; the TSSOP-16 is the hand-solderable package, with a smaller DSBGA-12 for dense layouts. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TSC2046 is a Texas Instruments 4-wire resistive touch screen controller in 16-pin TSSOP — the low-voltage-I/O successor to the ADS7846 for modern 1.8 V/3.3 V systems: 2.2 V to 5.25 V analog supply with 1.5 V to 5.25 V digital I/O, internal 2.5 V reference, direct battery measurement 0 V to 6 V, on-chip temperature and touch-pressure measurement, SPI 3-wire interface, auto power-down, 125 kHz sample rate, -40 to +85 °C. The 100% ADS7846 pin compatibility is the selection point: existing layouts upgrade to low-voltage I/O without a PCB spin — only the digital interface levels change. That makes it the safe pick for refreshing legacy resistive-touch products onto current logic rails. Selection advice: this is the upgrade over the ADS7846 on this site when your host runs 1.8 V logic — for I2C instead of SPI, the TSC2007 is the alternative; match the full orderable (e.g. TSC2046EIPWR for TSSOP reel) to your assembly process. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DAC8812IBPWR is a Texas Instruments dual 16-bit current-output multiplying DAC in TSSOP-16, tape and reel — 1 LSB maximum relative accuracy and differential nonlinearity, 2 mA full-scale current, 0.5 µs settling time, 50 MHz SPI-compatible 3-wire interface, double-buffered registers for simultaneous dual-channel updates, internal power-on reset, single 2.7 V to 5.5 V supply, rated −40 °C to +85 °C. The multiplying architecture is the selection point: the output scales with the reference, so it works as a digitally controlled attenuator or programmable gain element — a straight voltage-output DAC cannot do that job. Selection advice: IBPWR is the B-grade TSSOP reel version (2,000 per reel) — the DAC8812IBPW is the tube twin, the DAC8812ICPWR the C-grade (one accuracy step down) reel version; the DAC8811 is the single-channel and DAC8814 the quad-channel family member for different channel counts. TI lists this code Active; LCSC lists it as in stock and Rochester Electronics marks the manufacturer life cycle Active. Evidence: the TI DAC8812 packaging addendum (10-Nov-2025) confirms the ordering code, 16-bit dual multiplying architecture, TSSOP-16 reel and Active status. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ULN2003APWR is a Texas Instruments seven-channel Darlington transistor array in TSSOP-16, large tape and reel — for driving relays, solenoids and low-side loads from logic outputs. Seven integrated Darlington pairs with freewheeling diodes is the selection point: one chip replaces seven transistor-plus-diode circuits. Selection advice: the PWR suffix denotes TSSOP-16 in large tape and reel — the most compact production variant of the ULN2003A; watch thermal derating in the thin package when multiple 500 mA channels run simultaneously. For hand-solderable builds, the PDIP ULN2003AN is the alternative. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AM2434BSDFHIALVR is a Texas Instruments Sitara AM243x high-performance MCU: up to four 800 MHz Arm Cortex-R5F cores, a 400 MHz Cortex-M4F, and dual gigabit PRU-ICSSG industrial-communication subsystems in a 441-ball FCBGA (17.2 x 17.2 mm). It is TI's consolidation play for factory automation — the R5F cluster delivers deterministic servo-loop control while the PRU-ICSSG runs full protocol stacks for EtherCAT target, PROFINET device and EtherNet/IP adapter on the same silicon, replacing architectures that needed an MCU plus an external industrial-Ethernet ASIC or FPGA. Heat evidence: the AM243x is TI's mainstream platform for servo drives and remote I/O modules, and its datasheet remains under active revision (Rev. J, 2026), signaling continued TI investment in the family. Selection advice: the full orderable encodes silicon revision, feature configuration, temperature grade and the ALV 441-ball FCBGA package on tape and reel — match it character-for-character; the ALX 293-ball FCCSP is a smaller, footprint-incompatible alternative, and R5F count plus PRU features vary across AM2431/32/34. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AM6232ATGGHIALWR is a Texas Instruments Sitara AM62x processor: dual 1.4 GHz Arm Cortex-A53 plus a Cortex-M4F in a 425-ball FCCSP (13 x 13 mm). The value proposition is Linux-class compute at microcontroller-class power — the A53 pair runs full Yocto/Debian HMI stacks while the M4F handles real-time I/O, so one device replaces an applications processor plus a companion MCU in industrial panels and gateways, and deep-sleep states in the milliwatt class simplify thermal and power design. TI's long-lifecycle industrial positioning protects multi-year programs from forced redesigns. Heat evidence: the AM62x family has been one of TI's most heavily promoted industrial platforms since its 2022 launch, with broad trade-press coverage and multiple third-party system-on-module vendors building AM62x-based products for HMI and edge AI. Selection advice: the ALW FCCSP-425 is the compact package variant — the AM625/AM623/AM620-Q1 family shares one TI product folder, so confirm the exact orderable against the datasheet because family members differ in feature set; the G temperature code and W carrier suffix must match your assembly flow. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AWR2944ABGALTRQ1 is a Texas Instruments 76–81 GHz single-chip FMCW radar sensor in 266-ball FCCSP, tape and reel — 4 transmit and 4 receive channels, Arm Cortex-R5F plus C66x DSP plus radar hardware accelerator for signal processing, 4 MB on-chip memory, CAN-FD, Ethernet, hardware security module, AEC-Q100 qualified and ASIL-B capable. The fourth transmitter is the selection point: 33% higher angular resolution than previous-generation corner radars, which is what enables reliable blind-spot detection, lane-change assist and cross-traffic alert under UN R79 and NCAP requirements. Selection advice: the R suffix is tape and reel, Q1 is the automotive qualification; lower-cost LC/ECO variants exist for non-safety designs, so do not pay for the ASIL-B part in a non-safety application. Automotive radar designs require RF layout discipline — follow the TI reference design, not a generic BGA flow. Evidence: the TI AWR2944 datasheet (device nomenclature and packaging addendum) confirms the 4×4 channels, 266-ball FCCSP, reel packing and automotive qualification. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CC1101RGP is a Texas Instruments sub-1 GHz RF transceiver in VQFN-20, tube packaging — for proprietary wireless sensor links in metering, alarms and remote control. The sub-1 GHz operation is the selection point: better wall penetration and range than 2.4 GHz at the same power budget. Selection advice: the RGP suffix denotes VQFN-20 in tube — for production volumes, the RGPT tape-and-reel variant feeds pick-and-place directly. This is a transceiver, not a protocol stack — plan firmware for your own packet format or a lightweight stack. Match the order code to your assembly process. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CC1101RGPR is a sub-1 GHz RF transceiver from Texas Instruments in a 20-pin VQFN package, designed for low-power wireless links in metering, sensor networks, remote controls and home automation. Its advantage is the sub-1 GHz band: longer range and better obstacle penetration than 2.4 GHz for the same power budget, which is why it remains a workhorse for long-life battery-powered nodes. Selection advice: RGP denotes the VQFN-20 package and the trailing R tape-and-reel packing — match the full CC1101RGPR code to your BOM, since the CC1101 family ships in several package and packing combinations. RF performance depends on the matching network and antenna design around the chip, so this part is a component choice, not a drop-in module; confirm your region frequency-plan requirements when you RFQ. We reconfirm code, lot and traceability before quotation and reply within 24 hours.

CC1101RGPT is a Texas Instruments sub-1 GHz RF transceiver in VQFN-20, tape and reel — for proprietary wireless sensor links in metering, alarms and remote control. The sub-1 GHz operation is the selection point: better wall penetration and range than 2.4 GHz at the same power budget. Selection advice: the RGPT suffix denotes VQFN-20 in tape and reel for production assembly — the tube-packed RGP variant suits prototypes and hand assembly. This is a transceiver, not a protocol stack — plan firmware for your own packet format or a lightweight stack. Match the order code to your assembly process. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.