DS1307+

DS1302+ is an Analog Devices (Maxim) trickle-charge serial real-time clock with 3-wire interface in DIP-8 — for basic timekeeping with battery backup: appliances, simple controllers and legacy designs. The trickle-charge circuit is the selection point: it recharges the backup cell from VCC, extending field life. Selection advice: the + denotes the lead-free DIP-8 — pick the DS1302 for 3-wire serial interfaces; for I2C designs the DS1307 is the sibling; for accuracy without calibration, the DS3231's integrated TCXO is the step up. External 32.768 kHz crystal required. Parameters verified against the ADI official datasheet ordering table. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS3231SN# is an Analog Devices (Maxim) extremely accurate I2C real-time clock with integrated TCXO and crystal in 16-pin SO — for timekeeping that stays accurate without calibration: meters, data loggers and access systems. The ±2 ppm integrated TCXO is the selection point: seconds-per-month accuracy with no external crystal or trimming. Selection advice: the SN# suffix denotes 16-pin SO — pick the DS3231 over the cheaper DS1307 when accuracy matters; the DS1307 needs an external crystal and drifts far more. Battery backup keeps time through power loss. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS3232MZ+TRL is a temperature-compensated real-time clock with integrated memory from Analog Devices (Maxim Integrated) in a 20-pin SOIC package. Temperature compensation is the key advantage: the RTC holds its accuracy across temperature swings without external crystal trimming, which removes a calibration step from production and keeps timekeeping reliable in outdoor and industrial equipment. Selection advice: the + denotes the lead-free/RoHS configuration and TRL tape-and-reel packing — both must match your assembly and compliance requirements, so quote the full DS3232MZ+TRL code rather than the base DS3232. If your design needs battery backup, state your backup-power and date-code requirements in the RFQ; we reconfirm the offered lot, packing and traceability before quotation and reply within 24 hours.

AD620BRZ-R7 is an Analog Devices instrumentation amplifier in 8-lead SOIC_N, 7-inch tape and reel — gain set from 1 to 10,000 with a single external resistor, ±2.3 V to ±18 V dual supply (4.6 V to 36 V single), 15 µV maximum input offset (B grade), 1 MHz bandwidth, 1.3 mA maximum supply current, rated −40 °C to +85 °C. The single-resistor gain setting is the selection point: bridge sensors, thermocouples and strain gauges get a precision differential front end with one resistor instead of a matched-resistor op-amp network that drifts with temperature and layout. Selection advice: BRZ is the B grade (tighter offset than the A-grade AD620ARZ-R7), R-8 the SOIC package, R7 the 7-inch reel — the AD620BRZ-RL is the identical die on a 13-inch reel if your line prefers larger reels. DigiKey lists this code Active. Evidence: the ADI AD620 datasheet Rev. H ordering guide confirms the ordering code, B grade, 7-inch reel and −40 to +85 °C rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7192BRUZ-REEL is an Analog Devices 24-bit sigma-delta ADC with integrated PGA -- for precision measurement front ends: 2 differential or 4 pseudo-differential inputs, 4.7Hz to 4.8kHz output data rate, programmable gain from 1 to 128, 24-lead TSSOP, -40C to +105C. The on-chip low-noise gain stage lets small-amplitude sensor signals interface directly to the ADC without external amplification, and the automatic channel sequencer simplifies multi-channel acquisition firmware. Business impact: a complete analog front end in one device shrinks the signal chain BOM and board area for weigh scales, strain-gage transducers and PLC/DCS input modules -- fewer parts to qualify, fewer to source. Selection advice: the REEL suffix is the tape-and-reel packing for production -- for prototyping, the tube-packed AD7192BRUZ matches electrically; the 24-bit resolution is real only when the layout follows the datasheet grounding and decoupling guidance. Featured on the lcsc.com Lightning Deals list (2026-10-12). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7606BSTZ is an Analog Devices 8-channel, 16-bit simultaneous-sampling data acquisition system in LQFP-64 — for industrial DAQ: PLC analog inputs, power-line monitoring and vibration analysis. Eight truly simultaneous 16-bit channels is the selection point: phase-accurate multi-channel capture that multiplexed ADCs cannot deliver. Selection advice: the BSTZ suffix denotes LQFP-64 — confirm your input range and throughput against the datasheet; for fewer channels, the AD7606 family's 4/6-channel siblings cut cost. Plan the analog front end (filtering, protection) per ADI's reference circuits. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8066ARZ is an Analog Devices dual 145 MHz FastFET operational amplifier in 8-lead SOIC, tube packing — 180 V/µs slew rate, 7 nV/√Hz voltage noise, 1 pA-class FET input bias current, 5 V to 24 V supply, rail-to-rail output, -40 °C to +85 °C. The FastFET input stage is the selection point: photodiode preamps and high-impedance sensor front ends get wideband speed without the noise penalty of bipolar inputs. Selection advice: ARZ is the SOIC-8 tube code — AD8066ARZ-R7 is the reel twin, and the single-channel AD8065 covers single-op-amp designs. Honest availability note: Mouser currently flags this code as restricted availability, so confirm the lot before committing to production volumes. Evidence: the ADI AD8066 official datasheet confirms the bandwidth, slew rate and package codes, and Mouser confirms the exact ordering code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD9245BCPZ-80 is an Analog Devices 14-bit, 80 MSPS pipelined ADC — for IF sampling and data acquisition: 73.3dB SNR, 3V single supply (2.7-3.6V), differential or single-ended input, parallel CMOS output, 32-lead LFCSP (5x5mm), -40°C to 85°C. The 80 MSPS rate with 14-bit resolution captures IF bands directly, so receiver designs drop a downconversion stage; pin-compatible 10/12-bit siblings allow one PCB to serve multiple performance tiers. Business impact: the AD9245 family has shipped for two decades with stable supply — a safe choice for long-lifecycle instrumentation. Selection advice: the -80 grade is the 80 MSPS speed bin — for 65 MSPS the -65 grade is cheaper; BCPZ is the LFCSP package — verify the land pattern against the ADI datasheet. Ranked #3 on the hqbuy.com real-time hot list (2026-10-13). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD9361BBCZ is an Analog Devices RF Agile Transceiver covering 70 MHz to 6 GHz in 144-ball CSPBGA — for software-defined radio and wireless infrastructure: point-to-point links, femtocell/picocell base stations and test equipment. 2x2 MIMO with integrated 12-bit DACs/ADCs, 200 kHz to 56 MHz tunable channel bandwidth, dual receivers with 6 differential or 12 single-ended inputs, and multichip synchronization. Ranked #33 on the 创芯指数 March 2026 hot-search TOP 50 with 14,139 searches and a 267.53% month-on-month increase. Selection advice: the BBCZ code is the 144-ball CSPBGA tray version; the 10x10 mm BGA needs careful RF layout with solid ground stitching. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD9864BCPZ is an Analog Devices general-purpose IF digitizing subsystem in 48-lead LFCSP, tray packing — 10 MHz to 300 MHz IF input through a complete signal chain: low-noise amplifier, mixer, band-pass sigma-delta ADC and programmable decimation filter, with baseband I/Q serial digital output in 16 or 24 bits, on-chip LO and sample-clock synthesizers, SPI programming, 7.5 dB single-sideband noise figure, −7.0 dBm input third-order intercept, 12 dB continuous AGC range, 2.7 V to 3.6 V single supply at 17 mA typical, rated −40 °C to +85 °C. The single-chip IF-to-bits chain is the selection point: receiver designs that would otherwise need a discrete LNA, mixer, ADC and clock tree get the whole front end in one 7×7 mm package, which is why this part anchors legacy communications and instrumentation platforms. Selection advice: BCPZ is the tray version (260 per tray) — the AD9864BCPZRL is the identical device on 13-inch reel (2,500 per reel) for volume lines. ADI does not show a lifecycle status on the product page; DigiKey lists this code Active with stock, and no ADI discontinuance notice covers the AD9864 (PDN 21_0100 discontinued the AD9860/AD9862, not this part). Evidence: the ADI AD9864 datasheet Rev. B ordering guide confirms the ordering code, 48-lead LFCSP, tray packing and −40 to +85 °C rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.