2EDF7235K

ADUM4223ARWZ is an Analog Devices dual-channel isolated half-bridge driver — 16-lead wide-body SOIC, independent high-side and low-side outputs, 4 A peak output, 5 kV rms isolation, grade A UVLO (4.1 V typ), 5 ns channel matching. The 5 ns channel matching is the selection point: tight high/low-side timing for clean half-bridge switching — deadtime accuracy that discrete drivers cannot match. Selection advice: ADI lists the ADUM4223ARWZ as Production. The ARWZ code pins the 16-lead wide-body variant — match it to your footprint; the grade A UVLO suits 5 V logic drive. Verify the 4 A peak against your switch gate charge at the switching frequency, and the isolation working voltage against your safety standard. Evidence: ADI data confirms Production, 16-lead wide-body SOIC, 4 A peak, 5 kV rms isolation, 5 ns matching. Match the full ADUM4223ARWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM4223BRWZ is an Analog Devices iCoupler isolated dual gate driver in wide-body 16-SOIC — 4 A peak output, 5000 VRMS reinforced isolation, two independent isolated channels for high-side and low-side driving, 3.0 V to 5.5 V input supply, 4.5 V to 18 V output drive supply, 49 ns maximum propagation delay with 5 ns channel matching, >25 kV/µs common-mode transient immunity, -40 to +125 °C, tube packing (Z). The B grade is the selection point: 7.0 V UVLO threshold on the output supplies — designed for systems whose gate-drive rail is regulated below 12 V. Selection advice: the A/B/C grades differ only in the output-supply UVLO threshold (A 4.1 V, B 7.0 V, C 11.0 V) — pick the grade matching your actual gate-drive voltage. The WBRWZ/WCRWZ codes are the AEC-Q100 automotive variants. Evidence: ADI ADuM3223/4223 datasheet (Rev. I) and distributor listings confirm 4 A, 5000 VRMS, wide-body 16-SOIC and tube packing. Match the full ADUM4223BRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM4223CRWZ is an Analog Devices iCoupler isolated dual gate driver in wide-body 16-SOIC — 4 A peak output, 5000 VRMS reinforced isolation, two independent isolated channels for high-side and low-side driving, 3.0 V to 5.5 V input supply, 4.5 V to 18 V output drive supply, 49 ns maximum propagation delay with 5 ns channel matching, >25 kV/µs common-mode transient immunity, -40 to +125 °C, tube packing (Z). The C grade is the selection point: 11.0 V UVLO threshold on the output supplies — designed for 12 V gate-drive rails where the driver stays off until the rail is solid. Selection advice: the A/B/C grades differ only in the output-supply UVLO threshold (A 4.1 V, B 7.0 V, C 11.0 V) — pick the grade matching your actual gate-drive voltage. The WBRWZ/WCRWZ codes are the AEC-Q100 automotive variants. Evidence: ADI ADuM3223/4223 datasheet (Rev. I) and distributor listings confirm 4 A, 5000 VRMS, wide-body 16-SOIC and tube packing. Match the full ADUM4223CRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

STGAP2DMTR is an ST 1700 V isolated dual-channel gate driver — SO-16, 4 A drive, UVLO protection, galvanic isolation between gate drive signals, tape and reel. The 1700 V isolation is the selection point: dual-channel isolated drive for high-voltage SiC and IGBT stages — industrial drives and solar inverters where 600 V drivers cannot go. Selection advice: ST lists the STGAP2DMTR as Active. The DMTR suffix denotes SO-16 on tape and reel — match it to your footprint; the STGAP2SM is the single-channel narrow-body SO-8 sibling. Verify the isolation working voltage against your safety standard — 1700 V rating suits 1200 V-class power stages. Evidence: ST data confirms Active, 1700 V isolation, dual channel, SO-16, 4 A. Match the full STGAP2DMTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

STGAP2HDMTR is an STMicroelectronics dual-channel galvanically isolated gate driver in wide-body SO-36W — 4 A sink/source per channel at 25 °C, 75 ns propagation delay, ±100 V/ns common-mode transient immunity, tape-and-reel packing (MTR), −40 to +125 °C. Galvanic isolation per the ST datasheet: 6 kV surge rating, 3500 VRMS per UL 1577, IEC 60747-17 certified. The isolated dual-channel topology is the selection point: one part drives both sides of a half bridge or full bridge while keeping the control ground fully separated from the power stage, cutting the board space and discrete isolation parts a two-chip solution needs. Separate open and close outputs plus the Miller clamp let you tune turn-on/turn-off independently, while UVLO on both supplies, thermal shutdown, SD, BRAKE and configurable interlocking with dead time simplify shoot-through-proof designs for motor drives, inverters and EV charging. Selection advice: this is the dual (D) member of the STGAP2 family — the STGAP2HSx are the single-channel wide-body SO-8W parts; pick D when one package must cover both bridge legs, and keep its pinout off-limits as a drop-in for single-channel drivers. ST lists STGAP2HDMTR as Active. Evidence: ST STGAP2HD datasheet and ST eStore confirm 4 A, 75 ns, ±100 V/ns CMTI, isolation ratings, SO-36W and tape-and-reel packing. Match the full STGAP2HDMTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

2EDF7275K is an Infineon EiceDRIVER dual-channel isolated half-bridge gate driver — PG-TFLGA-13 5×5 mm, 4 A source / 8 A sink, functional galvanic isolation, UVLO 3.9 V/4.2 V, tape and reel. The 4 A/8 A asymmetric drive is the selection point: strong turn-off for fast SiC/GaN and IGBT switching in a 5×5 mm package — isolated drive without an optocoupler. Selection advice: Infineon lists the 2EDF7275K as Active and preferred. The K suffix denotes the TFLGA-13 package — the same die ships in DSO-16 as the 2EDF7275F (Not For New Design), so match the package code to your footprint. Verify the functional (not reinforced) isolation rating against your safety standard. Evidence: Infineon data confirms Active/preferred, TFLGA-13, 4 A/8 A, functional isolation, UVLO levels. Match the full 2EDF7275K code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

1EDN7511B is an Infineon EiceDRIVER single-channel low-side gate driver in PG-SOT23-6, tape and reel — for driving power MOSFETs from logic in compact SMPS stages. 4 A source / 8 A sink with 3.9 V UVLO is the selection point: asymmetric drive with logic-compatible turn-on threshold. Selection advice: the B suffix denotes the SOT-23-6 package — for the higher-UVLO variant suited to noisy rails, the 1EDN8511B is the sibling; the 4.2 V to 20 V range suits both 5 V and 12 V drive rails. Infineon lists this part as Active and preferred. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

1EDN8511B is an Infineon EiceDRIVER single-channel low-side gate driver in PG-SOT23-6, tape and reel — for driving power MOSFETs from logic in compact SMPS stages. 4 A source / 8 A sink with 7 V UVLO is the selection point: asymmetric drive with a higher turn-on threshold for noisy gate-drive rails. Selection advice: the B suffix denotes the SOT-23-6 package; the 8 V to 20 V range versus the 4.2 V to 20 V of the 1EDN7511B — pick this variant where a higher UVLO better rejects supply noise. Infineon lists this part as Active and preferred. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

2EDF7275F is an Infineon EiceDRIVER dual-channel isolated half-bridge gate driver — PG-DSO-16, 4 A source / 8 A sink, functional galvanic isolation, UVLO 3.9 V/4.2 V, tape and reel. The 4 A/8 A asymmetric drive is the selection point: strong turn-off for fast switching in a standard DSO-16 — isolated drive without an optocoupler. Selection advice: lifecycle note — Infineon lists the 2EDF7275F as Not For New Design; for new designs specify the 2EDF7275K (the Active/preferred TFLGA-13 variant of the same die), and for existing production confirm the exact 2EDF7275F code — the K and F suffixes are different packages and are not interchangeable. Verify the functional (not reinforced) isolation rating against your safety standard. Evidence: Infineon data confirms NFND, DSO-16, 4 A/8 A, functional isolation, UVLO levels. Match the full 2EDF7275F code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

2EDN7524F is an Infineon EiceDRIVER dual-channel low-side gate driver in PG-DSO-8, tape and reel — for driving power MOSFETs in SMPS and motor drives. 5 A source output with 3.9 V UVLO is the selection point: fast drive with logic-compatible turn-on threshold. Selection advice: the F suffix denotes the DSO-8 package — for the same driver in TSSOP-8, the 2EDN7524R is the sibling; the 4.2 V to 20 V range suits both 5 V and 12 V drive rails. Infineon lists this part as Not For New Design — treat it as a legacy reference for repairs and existing production; for new designs, the 2EDN7534F is the active-preferred successor. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.