TMC2241ATU+

TMC2209-LA-T is a Trinamic (Analog Devices) two-phase stepper motor driver in QFN-28 (5 x 5 mm), tape-and-reel packing (T) — 4.75 V to 29 V motor supply, up to 1.4 A RMS continuous coil current (2 A RMS range with external sense resistors), stealthChop2 and spreadCycle chopper modes, up to 1/256 microstepping with interpolation, single-wire UART plus STEP/DIR control, stallGuard4 sensorless stall detection, coolStep adaptive current control, −40 to +125 °C. The combination of stealthChop2 and the UART interface is the selection point: near-silent motion plus full register-level tuning (current, microsteps, chopper mode, diagnostics) from the host controller, replacing the dip-switch guesswork of legacy drivers in 3D printers, automation axes and precision positioning. Selection advice: the LA code is the 5 x 5 mm QFN-28; the -T suffix is tape and reel. For standalone STEP/DIR boards pick the MS1/MS2 pin-strap microstep setting, or drive it from UART for the full feature set — note that 1.4 A RMS is the internal-sense ceiling, so above that you need external sense resistors (2 A RMS range). Trinamic/ADI lists TMC2209-LA-T as recommended for new designs. Evidence: TMC2209 datasheet (Rev. 1.09) and distributor listings confirm 4.75–29 V, 1.4 A RMS, stealthChop2, stallGuard4, QFN-28 and tape-and-reel packing. Match the full TMC2209-LA-T code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620BRZ-R7 is an Analog Devices instrumentation amplifier in 8-lead SOIC_N, 7-inch tape and reel — gain set from 1 to 10,000 with a single external resistor, ±2.3 V to ±18 V dual supply (4.6 V to 36 V single), 15 µV maximum input offset (B grade), 1 MHz bandwidth, 1.3 mA maximum supply current, rated −40 °C to +85 °C. The single-resistor gain setting is the selection point: bridge sensors, thermocouples and strain gauges get a precision differential front end with one resistor instead of a matched-resistor op-amp network that drifts with temperature and layout. Selection advice: BRZ is the B grade (tighter offset than the A-grade AD620ARZ-R7), R-8 the SOIC package, R7 the 7-inch reel — the AD620BRZ-RL is the identical die on a 13-inch reel if your line prefers larger reels. DigiKey lists this code Active. Evidence: the ADI AD620 datasheet Rev. H ordering guide confirms the ordering code, B grade, 7-inch reel and −40 to +85 °C rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7192BRUZ-REEL is an Analog Devices 24-bit sigma-delta ADC with integrated PGA -- for precision measurement front ends: 2 differential or 4 pseudo-differential inputs, 4.7Hz to 4.8kHz output data rate, programmable gain from 1 to 128, 24-lead TSSOP, -40C to +105C. The on-chip low-noise gain stage lets small-amplitude sensor signals interface directly to the ADC without external amplification, and the automatic channel sequencer simplifies multi-channel acquisition firmware. Business impact: a complete analog front end in one device shrinks the signal chain BOM and board area for weigh scales, strain-gage transducers and PLC/DCS input modules -- fewer parts to qualify, fewer to source. Selection advice: the REEL suffix is the tape-and-reel packing for production -- for prototyping, the tube-packed AD7192BRUZ matches electrically; the 24-bit resolution is real only when the layout follows the datasheet grounding and decoupling guidance. Featured on the lcsc.com Lightning Deals list (2026-10-12). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7606BSTZ is an Analog Devices 8-channel, 16-bit simultaneous-sampling data acquisition system in LQFP-64 — for industrial DAQ: PLC analog inputs, power-line monitoring and vibration analysis. Eight truly simultaneous 16-bit channels is the selection point: phase-accurate multi-channel capture that multiplexed ADCs cannot deliver. Selection advice: the BSTZ suffix denotes LQFP-64 — confirm your input range and throughput against the datasheet; for fewer channels, the AD7606 family's 4/6-channel siblings cut cost. Plan the analog front end (filtering, protection) per ADI's reference circuits. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8066ARZ is an Analog Devices dual 145 MHz FastFET operational amplifier in 8-lead SOIC, tube packing — 180 V/µs slew rate, 7 nV/√Hz voltage noise, 1 pA-class FET input bias current, 5 V to 24 V supply, rail-to-rail output, -40 °C to +85 °C. The FastFET input stage is the selection point: photodiode preamps and high-impedance sensor front ends get wideband speed without the noise penalty of bipolar inputs. Selection advice: ARZ is the SOIC-8 tube code — AD8066ARZ-R7 is the reel twin, and the single-channel AD8065 covers single-op-amp designs. Honest availability note: Mouser currently flags this code as restricted availability, so confirm the lot before committing to production volumes. Evidence: the ADI AD8066 official datasheet confirms the bandwidth, slew rate and package codes, and Mouser confirms the exact ordering code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD9245BCPZ-80 is an Analog Devices 14-bit, 80 MSPS pipelined ADC — for IF sampling and data acquisition: 73.3dB SNR, 3V single supply (2.7-3.6V), differential or single-ended input, parallel CMOS output, 32-lead LFCSP (5x5mm), -40°C to 85°C. The 80 MSPS rate with 14-bit resolution captures IF bands directly, so receiver designs drop a downconversion stage; pin-compatible 10/12-bit siblings allow one PCB to serve multiple performance tiers. Business impact: the AD9245 family has shipped for two decades with stable supply — a safe choice for long-lifecycle instrumentation. Selection advice: the -80 grade is the 80 MSPS speed bin — for 65 MSPS the -65 grade is cheaper; BCPZ is the LFCSP package — verify the land pattern against the ADI datasheet. Ranked #3 on the hqbuy.com real-time hot list (2026-10-13). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD9361BBCZ is an Analog Devices RF Agile Transceiver covering 70 MHz to 6 GHz in 144-ball CSPBGA — for software-defined radio and wireless infrastructure: point-to-point links, femtocell/picocell base stations and test equipment. 2x2 MIMO with integrated 12-bit DACs/ADCs, 200 kHz to 56 MHz tunable channel bandwidth, dual receivers with 6 differential or 12 single-ended inputs, and multichip synchronization. Ranked #33 on the 创芯指数 March 2026 hot-search TOP 50 with 14,139 searches and a 267.53% month-on-month increase. Selection advice: the BBCZ code is the 144-ball CSPBGA tray version; the 10x10 mm BGA needs careful RF layout with solid ground stitching. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD9864BCPZ is an Analog Devices general-purpose IF digitizing subsystem in 48-lead LFCSP, tray packing — 10 MHz to 300 MHz IF input through a complete signal chain: low-noise amplifier, mixer, band-pass sigma-delta ADC and programmable decimation filter, with baseband I/Q serial digital output in 16 or 24 bits, on-chip LO and sample-clock synthesizers, SPI programming, 7.5 dB single-sideband noise figure, −7.0 dBm input third-order intercept, 12 dB continuous AGC range, 2.7 V to 3.6 V single supply at 17 mA typical, rated −40 °C to +85 °C. The single-chip IF-to-bits chain is the selection point: receiver designs that would otherwise need a discrete LNA, mixer, ADC and clock tree get the whole front end in one 7×7 mm package, which is why this part anchors legacy communications and instrumentation platforms. Selection advice: BCPZ is the tray version (260 per tray) — the AD9864BCPZRL is the identical device on 13-inch reel (2,500 per reel) for volume lines. ADI does not show a lifecycle status on the product page; DigiKey lists this code Active with stock, and no ADI discontinuance notice covers the AD9864 (PDN 21_0100 discontinued the AD9860/AD9862, not this part). Evidence: the ADI AD9864 datasheet Rev. B ordering guide confirms the ordering code, 48-lead LFCSP, tray packing and −40 to +85 °C rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADA4077-2ARZ is an Analog Devices dual precision operational amplifier in 8-lead SOIC, tube packing — 15 µV typical input offset (50 µV max A-grade), 0.25 µV/°C drift, 3.6 MHz gain-bandwidth, 1.2 V/µs slew rate, 1 nA input bias and 400 µA per channel, specified over −40 °C to +125 °C on 5 V to 30 V supplies (±2.5 V to ±15 V). Unity-gain stable with no phase reversal and stable into 1000 pF capacitive loads. The offset-plus-drift combination is the selection point: thermocouple, RTD and strain-gauge front ends hold calibration across temperature without trimming, which is the whole value proposition of a precision op amp. Selection advice: the ARZ code is the tube version — ARZ-R7/ARZ-RL is the same die on tape and reel for pick-and-place; this is not a rail-to-rail output part, so size your signal swing inside the ±15 V rails. For single-channel or quad layouts use the ADA4077-1/ADA4077-4. Evidence: LCSC and element14/Newark listings confirm 15 µV, 3.6 MHz, −40 to +125 °C, SOIC-8 and wide distributor stock. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADM3053BRWZ is an Analog Devices isolated CAN transceiver in 20-lead wide-body SOIC — 2.5 kVRMS signal and power isolation with the integrated isoPower isolated DC-DC converter, powered from a single 5 V supply (no separate isolated supply needed), 5 V or 3.3 V operation on VIO, ISO 11898 compliant, up to 1 Mbps, slope control for reduced EMI, thermal shutdown, >25 kV/µs common-mode transient immunity, -40 to +85 °C, tube packing (Z). The integrated isolated power is the selection point: the whole isolated CAN node runs from one 5 V rail — the competing ADM3052 needs a separate bus-side supply. Selection advice: the BRWZ code is the tube-packed version — the BRWZ-RL code is tape-and-reel, so match the packing suffix to your assembly process. Unpowered nodes do not disturb the bus; up to 110 nodes are supported. Evidence: ADI ADM3053 datasheet (Rev. E) and distributor listings confirm 2.5 kVRMS, isoPower, 20-SOIC, 1 Mbps and tube packing. Match the full ADM3053BRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.