STGAP2DMTR

STGAP2HDMTR is an STMicroelectronics dual-channel galvanically isolated gate driver in wide-body SO-36W — 4 A sink/source per channel at 25 °C, 75 ns propagation delay, ±100 V/ns common-mode transient immunity, tape-and-reel packing (MTR), −40 to +125 °C. Galvanic isolation per the ST datasheet: 6 kV surge rating, 3500 VRMS per UL 1577, IEC 60747-17 certified. The isolated dual-channel topology is the selection point: one part drives both sides of a half bridge or full bridge while keeping the control ground fully separated from the power stage, cutting the board space and discrete isolation parts a two-chip solution needs. Separate open and close outputs plus the Miller clamp let you tune turn-on/turn-off independently, while UVLO on both supplies, thermal shutdown, SD, BRAKE and configurable interlocking with dead time simplify shoot-through-proof designs for motor drives, inverters and EV charging. Selection advice: this is the dual (D) member of the STGAP2 family — the STGAP2HSx are the single-channel wide-body SO-8W parts; pick D when one package must cover both bridge legs, and keep its pinout off-limits as a drop-in for single-channel drivers. ST lists STGAP2HDMTR as Active. Evidence: ST STGAP2HD datasheet and ST eStore confirm 4 A, 75 ns, ±100 V/ns CMTI, isolation ratings, SO-36W and tape-and-reel packing. Match the full STGAP2HDMTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

2EDF7235K is an Infineon EiceDRIVER dual-channel isolated gate driver — PG-TFLGA-13, functional galvanic isolation, tape and reel. The coreless-transformer isolation is the selection point: dual-channel isolated drive in a 5×5 mm package with no optocoupler aging — for SiC/GaN and IGBT stages. Selection advice: lifecycle warning — Infineon lists the 2EDF7235K as discontinued (EOL announced May 2023); for new designs migrate to the current-generation 2EDF7xxx family, and for repairs and legacy builds we source remaining stock. Confirm the exact 2EDF7235K code on the BOM — the EiceDRIVER family spans many current and package variants that are not interchangeable. Evidence: Infineon data confirms discontinued status and the base ordering code. Match the full 2EDF7235K code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM4223ARWZ is an Analog Devices dual-channel isolated half-bridge driver — 16-lead wide-body SOIC, independent high-side and low-side outputs, 4 A peak output, 5 kV rms isolation, grade A UVLO (4.1 V typ), 5 ns channel matching. The 5 ns channel matching is the selection point: tight high/low-side timing for clean half-bridge switching — deadtime accuracy that discrete drivers cannot match. Selection advice: ADI lists the ADUM4223ARWZ as Production. The ARWZ code pins the 16-lead wide-body variant — match it to your footprint; the grade A UVLO suits 5 V logic drive. Verify the 4 A peak against your switch gate charge at the switching frequency, and the isolation working voltage against your safety standard. Evidence: ADI data confirms Production, 16-lead wide-body SOIC, 4 A peak, 5 kV rms isolation, 5 ns matching. Match the full ADUM4223ARWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM4223BRWZ is an Analog Devices iCoupler isolated dual gate driver in wide-body 16-SOIC — 4 A peak output, 5000 VRMS reinforced isolation, two independent isolated channels for high-side and low-side driving, 3.0 V to 5.5 V input supply, 4.5 V to 18 V output drive supply, 49 ns maximum propagation delay with 5 ns channel matching, >25 kV/µs common-mode transient immunity, -40 to +125 °C, tube packing (Z). The B grade is the selection point: 7.0 V UVLO threshold on the output supplies — designed for systems whose gate-drive rail is regulated below 12 V. Selection advice: the A/B/C grades differ only in the output-supply UVLO threshold (A 4.1 V, B 7.0 V, C 11.0 V) — pick the grade matching your actual gate-drive voltage. The WBRWZ/WCRWZ codes are the AEC-Q100 automotive variants. Evidence: ADI ADuM3223/4223 datasheet (Rev. I) and distributor listings confirm 4 A, 5000 VRMS, wide-body 16-SOIC and tube packing. Match the full ADUM4223BRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM4223CRWZ is an Analog Devices iCoupler isolated dual gate driver in wide-body 16-SOIC — 4 A peak output, 5000 VRMS reinforced isolation, two independent isolated channels for high-side and low-side driving, 3.0 V to 5.5 V input supply, 4.5 V to 18 V output drive supply, 49 ns maximum propagation delay with 5 ns channel matching, >25 kV/µs common-mode transient immunity, -40 to +125 °C, tube packing (Z). The C grade is the selection point: 11.0 V UVLO threshold on the output supplies — designed for 12 V gate-drive rails where the driver stays off until the rail is solid. Selection advice: the A/B/C grades differ only in the output-supply UVLO threshold (A 4.1 V, B 7.0 V, C 11.0 V) — pick the grade matching your actual gate-drive voltage. The WBRWZ/WCRWZ codes are the AEC-Q100 automotive variants. Evidence: ADI ADuM3223/4223 datasheet (Rev. I) and distributor listings confirm 4 A, 5000 VRMS, wide-body 16-SOIC and tube packing. Match the full ADUM4223CRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L6390DTR is an ST half-bridge gate driver — SO-16, 600 V high-side rail, 290 mA source / 430 mA sink, 50 V/ns dV/dt immunity, UVLO, tape and reel. The 50 V/ns dV/dt immunity is the selection point: robust half-bridge drive for fast-switching MOSFETs where high dv/dt causes false triggering in weaker drivers. Selection advice: ST lists the L6390DTR as Active. The DTR suffix denotes SO-16 on tape and reel — match it to your footprint. Verify the 290 mA/430 mA drive against your MOSFET gate charge at the switching frequency — for larger switches step up to a higher-current driver. Evidence: ST data confirms Active, SO-16, 600 V rail, drive currents, 50 V/ns immunity. Match the full L6390DTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

VNH7100BASTR is a STMicroelectronics automotive fully integrated H-bridge motor driver in SO-16 — for brushed DC motors in body, thermal and chassis systems: 15 A output current, 4–28 V supply, AEC-Q100 qualified, VIPower M0 technology, MultiSense analog current feedback and full diagnostics (short-to-ground/VCC, open-load, thermal shutdown). The integrated diagnostics let the ECU detect stalled or disconnected motors without external sense resistors, simplifying fault handling and wiring. Selection advice: the ASTR code is SO-16 tape and reel — PWM up to 20 kHz; for higher-current or 3-phase BLDC loads step up within the VIPower family rather than paralleling devices. Ranked #17 on the Chuangxin Index June 2026 breakout list (1,764 searches, +383.29% MoM) and #11 in July (1,329 searches, +300.30% MoM), with the July report text specifically flagging the VNH7100BAS as trending. Parameters verified against STMicroelectronics documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L293D is an STMicroelectronics push-pull four-channel H-bridge motor driver with internal clamp diodes in 16-pin PowerDIP — for small DC motors, steppers and relay coils: robot kits, toys and lab fixtures. 600 mA per channel with 4.5–36 V supply is the selection point: driving motors straight from logic pins with no external diodes. Selection advice: the D suffix denotes the internal clamp diodes — the key reason to pick the L293D over the L293; for higher currents, the L298N or modern integrated drivers are the step up. Mind the ~2 V saturation drop in your motor voltage budget. Parameters verified against the ST official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L6386ED013TR is an ST high-voltage high-side and low-side gate driver — SO-14, 600 V max bootstrap, 400 mA source / 650 mA sink, embedded comparator, bootstrap diode, tape and reel. The embedded comparator plus bootstrap diode is the selection point: current sensing and high-side supply in one driver — fewer external parts for 600 V half-bridge stages. Selection advice: ST lists the L6386ED013TR as Active. The ED013TR suffix pins the SO-14 package on tape and reel — match it to your footprint; the L6387 variant is the SO-8 version with fewer pins. Verify the 400 mA/650 mA drive against your MOSFET gate charge at the switching frequency. Evidence: ST data confirms Active, SO-14, 600 V bootstrap, drive currents, embedded comparator. Match the full L6386ED013TR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L6387ED013TR is an ST high-voltage high-side and low-side gate driver — SO-8, 600 V max, 400 mA source / 650 mA sink, embedded comparator, bootstrap diode, interlocking and current-sense support, tape and reel. The SO-8 package is the selection point: 600 V half-bridge drive in an 8-pin footprint — the compact sibling of the SO-14 L6386 for space-constrained power stages. Selection advice: ST lists the L6387ED013TR as Active. The ED013TR suffix pins the SO-8 package on tape and reel — match it to your footprint; the L6386 is the larger SO-14 variant. Verify the 400 mA/650 mA drive against your MOSFET gate charge at the switching frequency. Evidence: ST data confirms Active, SO-8, 600 V, drive currents, embedded comparator. Match the full L6387ED013TR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.