100+ staff · 1,500+ m² in Shenzhen and Hong Kong · Since 2002
ProductsPower ManagementLD1086D2T33TR
PACKAGE REFERENCED2PAKConfirm case, pinout and ordering suffix before purchase.
MANUFACTURER PART RECORD

LD1086D2T33TR

STMicroelectronics

LD1086D2T33TR is an STMicroelectronics LD1086 fixed 3.3 V low-dropout linear regulator — 1.5 A, in D2PAK (TO-263), tape-and-reel packing, input up to 30 V, operating -40 to +125 °C. The 1.3 V typical dropout at 1.5 A with ±1% output tolerance at 25 °C is the selection point: this is the part that makes 3.3 V from a 5 V rail where an LM317-class standard regulator runs out of headroom. Selection advice: pick the LD1086 family by dropout budget — if your input-output differential is under 2 V at full load, the LD1086 works and the LM317 does not; if headroom is generous, the LM317 is cheaper. The D2T (D2PAK) package carries more heat than the smaller DPAK sibling, so for continuous 1.5 A with a large voltage drop, prefer this D2PAK code and verify copper area; for lighter loads the DPAK variants save board space. Only 10 µF minimum output capacitance is needed for stability, and internal current and thermal limits are built in. Evidence: ST LD1086 datasheet and distributor listings confirm 3.3 V, 1.5 A, 1.3 V dropout, D2PAK and tape-and-reel. Match the full LD1086D2T33TR code for voltage, package and packing.

Power ManagementFixed linear regulatorD2PAK
MPN
LD1086D2T33TR
Manufacturer
STMicroelectronics
Family
Fixed linear regulator
Package
D2PAK
Manufacturer channel coverage
Checked by RFQ
Data last checked
Commercial check required
Required order checks
Suffix, package, date code, lot, source and traceability
Lifecycle
Active
PROCUREMENT DATA

Identity and sourcing requirements.

MANUFACTURER DATA REVIEW

Key technical specifications

Ordering-code highlights reviewed against official manufacturer documentation.

Regulator type
Fixed positive LDO regulator
Output voltage
3.3 V fixed
Maximum output current
1.5 A
Typical dropout
1.3 V at 1.5 A
Output tolerance
±1% at 25°C, ±2% full range
Operating temperature
-40°C to 125°C
Package
D2PAK
Source: STMicroelectronics LD1086 product data · DocID6739 Rev 38 · Reviewed 2026-09-29
ORDER-CODE COMPARISON

Same series, different order codes.

LD1086 is available in the following manufacturer order codes. They share the same Fixed linear regulator design; the table highlights package, packing and ordering differences. Quote the exact code your BOM needs.

Order codePackagePackingKey difference
LD1086BDTTRDPAK—Compared with LD1086DT33TR, this code specifies adjustable output and DPAK packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.
LD1086BV-DGTO-220—Compared with LD1086DT33TR, this code specifies adjustable output and TO-220 packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.
LD1086D2M33TRD2PAK—Compared with LD1086DT33TR, this code specifies 3.3 V output and D2PAK packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.
LD1086D2MTRD2PAK—Compared with LD1086DT33TR, this code specifies adjustable output and D2PAK packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.
LD1086D2T33TRD2PAKTape and reelFixed 3.3 V output
LD1086D2TTRD2PAK—Compared with LD1086DT33TR, this code specifies adjustable output and D2PAK packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.
LD1086DT33TRTO-252——
LD1086DT50TRDPAKTape and reelFixed 5.0 V output
LD1086DTTRDPAK—Compared with LD1086DT33TR, this code specifies adjustable output and DPAK packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.
LD1086PURDFN8 4x4—Compared with LD1086DT33TR, this code specifies adjustable output and DFN8 4x4 packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.
LD1086V-DGTO-220—Compared with LD1086DT33TR, this code specifies adjustable output and TO-220 packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.
LD1086V33-DGTO-220—Compared with LD1086DT33TR, this code specifies 3.3 V output and TO-220 packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.
QUOTE WORKFLOW

Four checks before a commercial offer.

01

Identity

Exact MPN, manufacturer and suffix

02

Supply

Supplier type, quantity and freshness

03

Evidence

Lot, labels, photos and documents

04

Terms

Price, lead time, payment and shipping

RELATED REFERENCES

Explore more Power Management records

Browse existing catalog records — same series first, then the same category and manufacturer. These are not confirmed replacements; compatibility requires engineering review.

MARKET INSIGHTS

Procurement coverage for LD1086D2T33TR

In-depth buyer guides on the market forces affecting this part category — allocation, mergers and technology shifts.

COMMON QUESTIONS

LD1086D2T33TR FAQ

What is the difference between LD1086D2T33TR and LD1086BDTTR, LD1086BV-DG, LD1086D2M33TR?

These are order-code variants of the same STMicroelectronics series. They share the core design; the ordering code selects the exact configuration — LD1086BDTTR: Compared with LD1086DT33TR, this code specifies adjustable output and DPAK packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.; LD1086BV-DG: Compared with LD1086DT33TR, this code specifies adjustable output and TO-220 packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.; LD1086D2M33TR: Compared with LD1086DT33TR, this code specifies 3.3 V output and D2PAK packaging. An adjustable version needs an external setting network; a package change requires footprint and thermal review.. LD1086D2T33TR itself is the D2PAK configuration. A code that differs by even one character may be a different device, so always quote the complete code exactly as it appears on your BOM.

What are the key specifications of LD1086D2T33TR?

From the verified technical profile: Regulator type: Fixed positive LDO regulator; Output voltage: 3.3 V fixed; Maximum output current: 1.5 A. These are the catalog-recorded values for LD1086D2T33TR — always re-check them against the manufacturer datasheet revision quoted on your BOM before finalizing the design.