GRM21BR61E106KA73L

Murata GRM21BR61C106KE15L is a 10 µF ±10% multilayer ceramic capacitor rated 16 V, X5R dielectric, in the 0805 (2012 metric) package, operating -55 to +85 °C. Its advantage for procurement is workhorse coverage: 10 µF/16 V in 0805 handles power-rail input/output filtering across 5 V and 12 V domains, the most common bulk-decoupling slot on industrial and consumer boards. Selection advice: apply voltage derating — MLCC capacitance falls under DC bias, so on a 12 V rail a 16 V-rated X5R part delivers well below its 10 µF nominal; keep roughly 2:1 voltage margin on power rails or verify effective capacitance in Murata SimSurfing. Also note X5R is rated to 85 °C maximum — if board ambient exceeds that, step up to the X7R equivalent. Evidence: distributor listings (DigiKey/element14) confirm 10 µF ±10%, 16 V, X5R, 0805 and Active status, 3,000/reel. Confirm packing and date-code requirements in your RFQ — we reply within 24 hours.

GRM21BR61H106KE43L is a 10 µF, 50 V X5R multilayer ceramic capacitor from Murata in an 0805 package — bulk decoupling in a smaller footprint than the 1206 equivalent. The 0805/10 µF/50 V combination is the selection point for space-constrained power rails: same bulk capacitance as the 1206 part where board area is tight. Selection advice: the X5R dielectric has a narrower temperature range than X7R — confirm your operating temperature stays within the X5R band. As with all high-value ceramics, check DC-bias derating at your rail voltage. Match the full code for packaging. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Murata GRM188C80G476ME01D is a 47 µF ±20% multilayer ceramic capacitor rated 4 V, X6S dielectric, in the 0603 (1608 metric) package, operating -55 to +105 °C. Its advantage for procurement is volumetric efficiency: 47 µF in a 0603 footprint gives bulk decoupling where board space is scarcest — wearables, modules and dense digital boards. Selection advice: watch DC-bias derating — a 4 V-rated X6S part loses a large share of its nominal capacitance when biased near its rating, so on a 3.3 V rail the effective capacitance can be far below 47 µF; if you need guaranteed minimum capacitance, choose a higher-voltage-rated part (6.3 V/10 V, often in 0805) or check Murata SimSurfing capacitance-vs-bias curves before committing the BOM. X6S (±22% over temperature) is fine for decoupling but not for timing or precision filtering. Evidence: distributor listings (DigiKey) confirm 47 µF ±20%, 4 V, X6S, 0603 and Active status, 4,000/reel. Confirm packing and date-code requirements in your RFQ — we reply within 24 hours.

GRM188R71H104KA93D is a 0.1 µF, 50 V X7R multilayer ceramic capacitor from Murata in a 0603 package — the industry-standard decoupling capacitor value. The 0.1 µF / 50 V / X7R combination is the selection point: the default bypass capacitor for digital IC power pins, stable capacitance across temperature with the X7R dielectric. Selection advice: the KA93D suffix denotes the packaging and tolerance configuration — match the full code for automated assembly. For decoupling, place the capacitor as close as possible to the IC power pin; confirm your rail voltage stays well within the 50 V rating with derating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Murata GRM31CR61E476ME44L is a 47 µF ±20% multilayer ceramic capacitor rated 25 V, X5R dielectric, in the 1206 (3216 metric) package, operating -55 to +85 °C. Its advantage for procurement is electrolytic replacement: 47 µF in 1206 holds the rail through load steps and smooths ripple at converter inputs and outputs without the wear-out mechanism of tantalum or aluminum electrolytics. Selection advice: the 25 V rating suits 12 V input stages and 5 V outputs with derating headroom — but verify effective capacitance under DC bias in Murata SimSurfing, since a 25 V-rated X5R at 12 V bias still sheds meaningful capacitance; and the X5R 85 °C ceiling is the main limit to check against hot enclosures, where an X7R part would be safer. Evidence: distributor listings (DigiKey/Arrow) confirm 47 µF ±20%, 25 V, X5R, 1206 and Active status. Confirm packing and date-code requirements in your RFQ — we reply within 24 hours.

GRM31CR71E106KA12L is a 10 µF X7R multilayer ceramic capacitor from Murata in a 1206 package — for bulk decoupling and power-rail smoothing where 0.1 µF ceramics are not enough. The 10 µF value in 1206 is the selection point: bulk capacitance with low ESR for switching-regulator outputs and IC power inputs, in a package that handles the ripple current. Selection advice: ceramic capacitors lose capacitance under DC bias — verify the effective capacitance at your actual rail voltage against the datasheet DC-bias curves, and parallel with 0.1 µF ceramics for high-frequency decoupling. Match the full code for packaging. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

C1608X7R1H104K080AA is a 0.1 µF, 50 V X7R multilayer ceramic capacitor from TDK in a 0603 package (1608 metric) — the standard decoupling capacitor for digital power rails. The X7R dielectric is the selection point over Y5V: capacitance stays stable across the temperature range, which keeps decoupling effective in industrial environments. Selection advice: the 080AA suffix denotes the packaging configuration — match the full code for your assembly process. TDK and Murata 0.1 µF/50 V/X7R/0603 parts are functionally interchangeable for decoupling, which gives you a second source without redesign. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Yageo CC0402KRX7R7BB104 is a 0.1 µF ±10% multilayer ceramic capacitor rated 16 V, X7R dielectric, in the 0402 (1005 metric) package, operating -55 to +125 °C. Its advantage for procurement is cost-positioning: 16 V is the sweet-spot rating for 3.3 V and 5 V rails — enough derating margin for stable effective capacitance at a lower price than the 50 V sibling (CC0402KRX7R9BB104). Selection advice: standardize on this 16 V version for all low-voltage digital decoupling and reserve the 50 V variant for higher rails or surge-exposed nodes; mixing the two on one BOM without need just splits purchase volume. Tolerance code K denotes ±10%. Evidence: distributor listings (Farnell/CPC/Newark) confirm 0.1 µF ±10%, 16 V, X7R, 0402 and -55 to +125 °C. Confirm packing and date-code requirements in your RFQ — we reply within 24 hours.

Yageo CC0402KRX7R9BB103 is a 10 nF (0.01 µF) ±10% multilayer ceramic capacitor rated 50 V, X7R dielectric, in the 0402 (1005 metric) package, operating -55 to +125 °C. Its advantage for procurement is high-frequency bypass: 10 nF in 0402 pairs with 0.1 µF for broadband decoupling, the smaller value higher self-resonant frequency and low ESL covering the upper frequency band where larger caps turn inductive. Selection advice: use 10 nF where high-frequency EMI filtering and fast-transient bypass matter; for bulk charge reservoir prefer 0.1 µF. X7R is the right economy choice for decoupling — only specify C0G/NP0 at this value for timing or precision-filter circuits where capacitance stability justifies the premium. Evidence: Yageo datasheet and distributor listings (Farnell/CPC) confirm 10 nF ±10%, 50 V, X7R, 0402 and -55 to +125 °C. Confirm packing and date-code requirements in your RFQ — we reply within 24 hours.

Yageo CC0402KRX7R9BB104 is a 0.1 µF ±10% multilayer ceramic capacitor rated 50 V, X7R dielectric, in the 0402 (1005 metric) package, operating -55 to +125 °C with Ni-barrier terminations. Its advantage for procurement is that it is the universal decoupling value: 0.1 µF covers the great majority of IC bypass needs, and the 50 V rating leaves enormous derating margin on low-voltage rails so effective capacitance stays near nominal. Selection advice: 0.1 µF/50 V/0402 is the safest default, but on cost-optimized high-volume boards a 16 V or 25 V rating is cheaper and fully sufficient for 3.3/5 V rails — only pay for 50 V where the rail voltage or surge environment demands it. Tolerance code K denotes ±10%; match the full Yageo CC series ordering code. Evidence: distributor listings (Farnell/CPC) confirm 0.1 µF ±10%, 50 V, X7R, 0402 and -55 to +125 °C. Confirm packing and date-code requirements in your RFQ — we reply within 24 hours.