MCP6002-I/P

LMV358IDR is a Texas Instruments dual low-voltage operational amplifier in 8-pin SOIC — the 5 V-and-below workhorse for cost-sensitive signal conditioning: appliance controls, HVAC boards and portable instruments. 2.7 V to 5.5 V supply, 1 MHz gain bandwidth, rail-to-rail output swing, 210 µA typical supply current per channel, -40 to +125 °C operation. The low-voltage design is the selection point over the classic LM358: full specified performance at 3.3 V and 5 V single supplies where the LM358 is out of its comfort zone, with no crossover distortion. Selection advice: this is the low-voltage sibling of the LM358 on this site — pick the LMV358 for 3.3 V/5 V-only designs; keep the LM358 when the rail goes above 5.5 V or below ground sensing matters. The IDR code is the 2500-reel SOIC. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TLV9002IDGKR is a Texas Instruments dual rail-to-rail input/output operational amplifier in 8-pin VSSOP — for space-constrained low-voltage designs that need modern RRIO performance at commodity cost: smoke detectors, wearables and small appliances. 1.8 V to 5.5 V supply, 1 MHz gain bandwidth, 2 V/µs slew rate, 60 µA per channel, 5 pA input bias current, -40 to +125 °C. The CMOS RRIO architecture with EMI-hardened inputs is the selection point: true rail-to-rail operation on both input and output at 1.8 V, where bipolar parts cannot go, with integrated RFI filtering for noisy environments. Selection advice: this is the cost-optimized RRIO alternative to the LMV358 on this site — pick the TLV9002 for 1.8 V operation or smaller VSSOP footprint; the LMV358 covers the SOIC footprint at lower unit cost. The IDGKR code is the VSSOP-8 reel — confirm the 3 x 4.9 mm footprint against your layout. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP4725A0T-E/CH is a Microchip 12-bit single-channel digital-to-analog converter with on-board EEPROM, I2C interface, buffered rail-to-rail output, in SOT-23-6, 2.7 to 5.5 V supply, -40 to +125 °C. The EEPROM is the selection point: the DAC powers up to the stored output code without MCU initialization, which is exactly what set-and-forget control outputs — bias trims, threshold references, drive levels — need to survive power cycles. Performance facts that matter for procurement: 6 µs settling, ±0.2 LSB DNL, 210 µA supply current, and I2C up to 3.4 MHz. Selection advice: the A0 in the code is the external address pin, so multiple MCP4725 variants with different address options can share one I2C bus — confirm the address option against your bus map before ordering, and choose this EEPROM version over plain DACs only when power-on recall is genuinely required, since it costs more than a volatile-output equivalent. Distributor listings mark this ordering code AEC-Q100, useful for automotive-adjacent programs. Evidence: Microchip datasheet and Farnell/element14 listings confirm 12-bit, I2C, EEPROM, SOT-23-6 and 2.7-5.5 V. Match the full MCP4725A0T-E/CH code for the address option and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP6002-I/SN is a dual low-power rail-to-rail operational amplifier from Microchip Technology in an 8-pin SOIC package — for sensor interfaces and battery-powered signal chains. The rail-to-rail input/output on a 1.8 V to 6 V supply is the selection point: full signal swing from a single low-voltage rail, which is exactly what 3.3 V sensor nodes need. Selection advice: the I/SN suffix denotes the industrial temperature grade in SOIC-8 — the MCP6002 ships in multiple packages, so match the full MCP6002-I/SN code to your footprint. Confirm your gain-bandwidth and offset requirements against the datasheet; this is a low-power part, not a precision part. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP6002T-I/SN is a Microchip dual CMOS operational amplifier in 8-pin SOIC (tape-and-reel packing, T suffix) — rail-to-rail input and output, 1 MHz gain-bandwidth product, 0.6 V/us slew rate, 4.5 mV maximum input offset voltage, 1 pA input bias current, only 100 uA quiescent current for both channels from 1.8 V to 6 V, −40 to +85 °C (I temperature grade). The rail-to-rail input/output on a 1.8–6 V supply is the selection point: it runs directly from a single Li-ion cell or 3.3 V rail and still swings signals nearly to both rails, so low-side current sensing, battery-powered signal conditioning and ADC buffering need no split supply or input biasing tricks. Selection advice: the T means tape and reel; the same base part without T is the tube-packaged MCP6002-I/SN — match the full ordering code to what your line runs. Do not confuse this I-grade (−40 to +85 °C) part with the wider-temperature members of the family; check your worst-case ambient before design-in. Microchip lists MCP6002T-I/SN as In Production. Evidence: Microchip MCP6002 datasheet and official product page confirm 1 MHz, 0.6 V/us, 4.5 mV, 1 pA, 100 uA, 1.8–6 V, 8-SOIC and tape-and-reel packing. Match the full MCP6002T-I/SN code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM358P is a Texas Instruments LM358 dual operational amplifier in PDIP-8, tube packaging — single supply 3 V to 32 V (or ±1.5 V to ±16 V dual), input common-mode range includes ground, unity-gain stable, two independent op-amps on one die. The PDIP-8 package is the selection point: through-hole for breadboards, teaching labs, prototyping and legacy repairs — the same LM358 die ships in SOIC, TSSOP and VSSOP under different suffixes, so match the full LM358P code to your board. Selection advice: the ground-sensing input of the LM358 is why it survives in single-supply sensor front ends where older op-amps cannot swing low enough — pick it for comparators, active filters and transducer amplifiers on a single rail. It is not rail-to-rail output and not precision (millivolt offsets), so for low-voltage precision work step up to a modern RRIO part. As the most remarked jellybean op-amp in the market, require lot traceability. Evidence: TI LM358 product page confirms PDIP-8, 3–32 V single supply and ground-sensing inputs. Match the full LM358P code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM393P is a Texas Instruments dual differential voltage comparator in 8-pin PDIP, tube packaging — open-collector outputs, 1.3 µs typical response time, 2 V to 36 V single-supply (or ±1 V to ±18 V dual) operation, common-mode input range that includes ground, 0 to +70 °C (P = PDIP commercial grade). The open-collector outputs with a ground-including input range are the selection point: it runs from a single 5 V rail while sensing signals down to ground, and the outputs wire-OR together for window detectors, level shifters and zero-crossing detectors in limit monitoring, battery supervisors and fan controllers. Selection advice: the P suffix is the PDIP-8 tube version — the same die ships as LM393D/DR (SOIC) for SMD lines; and because it is a comparator rather than an op amp, do not substitute an LM358 here — dedicated comparators switch far faster under saturated conditions and tolerate the high differential input voltages that would latch an op amp. TI lists LM393P as Active. Evidence: TI LM393/LM2903 datasheet and distributor listings confirm dual channels, open-collector, 1.3 µs, 2–36 V, PDIP-8 and tube packing. Match the full LM393P code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists NE5532P as an ACTIVE dual low-noise operational amplifier for audio applications in PDIP-8, with 10 MHz gain bandwidth, 9 V/µs slew rate and 10 V to 30 V supply range. The low-noise bipolar input stage is the selection point: it became the reference audio op-amp for mixing consoles and phono stages, and remains the benchmark newer audio op-amps are compared against. Selection advice: the P suffix denotes PDIP-8 — the NE5532 also ships in SOIC-8, so match the full NE5532P code to your footprint. For the lowest distortion, compare against the FET-input OPA2134; for the classic low-noise bipolar sound, match this code exactly. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TI lists OPA2134PA as ACTIVE — a dual SoundPlus FET-input audio op amp, 8 MHz GBW, 20 V/µs slew rate, 0.00008% THD, ±2.5 V to ±18 V supply, PDIP-8 tube packaging. The SoundPlus audio pedigree is the selection point: FET inputs for high impedance plus genuinely low distortion, which is why this part is the upgrade choice where the NE5532 noise or distortion budget falls short. Selection advice: the PA suffix denotes PDIP-8 — the OPA2134 ships in SOIC and other packages, so match the full code to your footprint. For new designs, compare against current-production audio op-amps if your rails or power budget differ from classic ±15 V designs. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists TL072CP as a dual JFET-input operational amplifier in PDIP-8 — for high-input-impedance analog signal paths such as guitar preamps, piezo buffers and electrometer front ends. The JFET input stage is the selection point: picoamp-level input bias current that bipolar op-amps cannot match, which is why the TL072 dominated audio and sensor front ends for decades. Selection advice: the CP suffix denotes PDIP-8 in tube packaging — the TL072 also ships in SOIC-8, so match the full TL072CP code to your footprint and packing needs. For lower noise, compare against the NE5532; for the classic JFET-input behavior, match this code exactly. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Microchip and Navitas showed an 800V-to-6V GaN reference design for AI racks, targeting 96% efficiency. What the design actually is, what it signals for component selection, and a five-point buyer checklist.