MCP6002T-I/SN

MCP6002-I/SN is a dual low-power rail-to-rail operational amplifier from Microchip Technology in an 8-pin SOIC package — for sensor interfaces and battery-powered signal chains. The rail-to-rail input/output on a 1.8 V to 6 V supply is the selection point: full signal swing from a single low-voltage rail, which is exactly what 3.3 V sensor nodes need. Selection advice: the I/SN suffix denotes the industrial temperature grade in SOIC-8 — the MCP6002 ships in multiple packages, so match the full MCP6002-I/SN code to your footprint. Confirm your gain-bandwidth and offset requirements against the datasheet; this is a low-power part, not a precision part. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP4725A0T-E/CH is a Microchip 12-bit single-channel digital-to-analog converter with on-board EEPROM, I2C interface, buffered rail-to-rail output, in SOT-23-6, 2.7 to 5.5 V supply, -40 to +125 °C. The EEPROM is the selection point: the DAC powers up to the stored output code without MCU initialization, which is exactly what set-and-forget control outputs — bias trims, threshold references, drive levels — need to survive power cycles. Performance facts that matter for procurement: 6 µs settling, ±0.2 LSB DNL, 210 µA supply current, and I2C up to 3.4 MHz. Selection advice: the A0 in the code is the external address pin, so multiple MCP4725 variants with different address options can share one I2C bus — confirm the address option against your bus map before ordering, and choose this EEPROM version over plain DACs only when power-on recall is genuinely required, since it costs more than a volatile-output equivalent. Distributor listings mark this ordering code AEC-Q100, useful for automotive-adjacent programs. Evidence: Microchip datasheet and Farnell/element14 listings confirm 12-bit, I2C, EEPROM, SOT-23-6 and 2.7-5.5 V. Match the full MCP4725A0T-E/CH code for the address option and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Microchip lists MCP6002-I/P as In Production — a dual 1 MHz rail-to-rail op amp, 1000 kHz gain-bandwidth, max 170 µA quiescent current, PDIP-8 tube packaging. Rail-to-rail input and output is the selection point for single-supply designs: the full signal swing is usable on low-voltage rails where a classic LM358 would clip. Selection advice: the I/P suffix denotes the industrial temperature grade in PDIP-8 — the MCP6002 ships in several grades and SMD packages, so match the full code. At 170 µA quiescent current it suits battery-powered signal chains; confirm your bandwidth need against the 1 MHz GBW. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620ARZ is a low-power instrumentation amplifier from Analog Devices in an 8-pin SOIC package, with gain set by a single external resistor — for bridge sensors, strain gauges and other small differential signals. Its advantage is the classic three-op-amp instrumentation topology in one package: high common-mode rejection with minimal external circuitry, which shortens precision front-end design. Selection advice: the ARZ suffix denotes the standard grade in SOIC-8 on tape and reel — the AD620 also ships in DIP and higher grades, so match the full code to your footprint and accuracy requirements. Gain is set by one resistor value, so confirm your gain calculation against the datasheet formula during design. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD623ARZ-R7 is an Analog Devices single-supply instrumentation amplifier, rail-to-rail output, gain 1 to 1000 set by one external resistor, 800 kHz bandwidth at G=1, in SOIC-8 — the sensor front-end amplifier for bridges, thermocouples and low-level transducer signals. The single-resistor gain programming is the selection point: no matched resistor networks to source, with 0.10% gain accuracy at G=1, 200 µV max offset and 550 µA max supply current for battery-powered instruments. Selection advice: it runs on 3 to 12 V single supply or ±2.5 to ±6 V dual supply — but note the input range extends only 150 mV below ground on a single rail, so ground-referenced bipolar sensor signals still need the dual-supply configuration. The R7 suffix is the 7-inch reel (1000 pcs) packing of the SOIC-8. For higher precision or lower noise, compare the AD620/AD8221 family rather than assuming drop-in equivalence. Parameters verified against the ADI AD623 datasheet and Mouser/LCSC listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8422BRZ is an Analog Devices rail-to-rail instrumentation amplifier in SOIC-8 — for bridge sensors, strain gauges and low-level differential signals where a discrete op-amp network drifts with temperature and layout. Gain is set by a single external resistor from 1 to 1000, with 25µV maximum input offset, 2.2MHz bandwidth and 150dB CMRR at high gain — precision front-end performance with minimal external circuitry. Selection advice: the BRZ code is the B grade (tighter offset than the A grade) in SOIC-8 tube packing — for reel packing specify the BRZ-R7; the MSOP-8 BRMZ suits tighter layouts. At 300µA supply current it fits battery-powered instruments, but confirm the 4.6V-to-36V supply span against your rails — for single 3.3V-only systems check the input range limits. For higher bandwidth or lower noise, compare the AD8421/AD8429 family rather than assuming interchangeability. Parameters verified against Analog Devices documentation and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8606ARZ is a dual rail-to-rail precision operational amplifier from Analog Devices in an 8-pin SOIC package — for low-voltage precision systems, data acquisition front ends and medical instrumentation. The combination of precision DC specs with rail-to-rail operation is the selection point: it brings precision-grade offset and drift to single-supply low-voltage designs that older precision op-amps cannot serve. Selection advice: the ARZ suffix denotes SOIC-8 on tape and reel — match the full AD8606ARZ code to your footprint and packing needs. Confirm your offset, drift and noise requirements against the datasheet before substituting for a general-purpose op-amp. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8610AR is an Analog Devices precision JFET-input operational amplifier — for photodiode front ends, precision instrumentation and active filters: 25MHz gain-bandwidth product, JFET input stage with picoamp-level bias current, low offset voltage, SOIC-8 package. The JFET inputs draw negligible bias current, so high-impedance sensor interfaces avoid the loading errors that bipolar-input op amps introduce; the 25MHz bandwidth handles fast signal chains while maintaining precision DC accuracy. Business impact: precision JFET op amps command a premium but eliminate an entire class of front-end error — designs that need both speed and high input impedance have few alternatives at this performance level. Selection advice: the AR suffix denotes SOIC-8 — for space-constrained layouts consider the ARMZ (MSOP) variant; the AD8610 is the single version — for dual-channel designs the AD8620 shares the same core. Ranked #7 on the hqew.com hot list (2026-10-05). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM7801-8BRIZ is an Analog Devices 25 MHz isolated ADC with sigma-delta modulated bit-stream output in 8-lead wide-body SOIC, for shunt current sensing in motor drives, solar inverters, and power converters. It delivers 16 bits with no missing codes over a +/-320 mV full-scale input, 88 dB typical SNR, and 5700 V rms isolation with 200 kV per us minimum common-mode transient immunity, so the controller side stays protected from noisy high-voltage power stages. The benefit is replacing an ADC plus optocoupler pair with one isolated part: the digital output crosses the barrier directly, cutting board area and preserving accuracy in high-dV/dt environments. Selection advice: the output is a pulse-density bit stream, not a parallel word, so your controller or FPGA must implement a sinc3 decimation filter; match the clock rate to your bandwidth and SNR target per the datasheet. The 8BRIZ code is the tube-packed wide-body SOIC version; for reel packing order the -RL code. Listed in DigiKey New Product Arrivals. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM7801-8BRIZ-RL is the tape-and-reel packing of the Analog Devices 25 MHz isolated ADC with sigma-delta modulated bit-stream output in 8-lead wide-body SOIC, for production runs of shunt current sensing in motor drives, solar inverters, and power converters. It delivers 16 bits with no missing codes over a +/-320 mV full-scale input, 88 dB typical SNR, and 5700 V rms isolation with 200 kV per us minimum common-mode transient immunity, so the controller side stays protected from noisy high-voltage power stages. The benefit is replacing an ADC plus optocoupler pair with one isolated part: the digital output crosses the barrier directly, cutting board area and preserving accuracy in high-dV/dt environments. Selection advice: the output is a pulse-density bit stream, not a parallel word, so your controller or FPGA must implement a sinc3 decimation filter; match the clock rate to your bandwidth and SNR target per the datasheet. The -RL suffix denotes reel packing; for tube packing order the base 8BRIZ code. Listed in DigiKey New Product Arrivals. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Microchip and Navitas showed an 800V-to-6V GaN reference design for AI racks, targeting 96% efficiency. What the design actually is, what it signals for component selection, and a five-point buyer checklist.