AD8604DRUZ

LM324DT is an STMicroelectronics quad low-power operational amplifier in SO-14 — four independent internally frequency-compensated op amps, 1.3 MHz gain-bandwidth product, 0.5 V/µs slew rate, 7 mV maximum input offset, single 3 V to 32 V or dual ±1.5 V to ±16 V supply, common-mode input range including ground, tape-and-reel packing (T), 0 to +70 °C. The four-amplifier single-supply integration is the selection point: the industry-standard quad for 5 V systems — comparators, filters, summers and transducer amplifiers in one SO-14 package with supply current independent of supply voltage. Selection advice: the DT code is the SO-14 reel version — the N code is DIP-14 and PT is TSSOP-14, so match the full LM324DT code for package and packing. Not rail-to-rail; allow headroom on both rails. Evidence: ST LM324 datasheet and distributor listings confirm quad, 1.3 MHz, SO-14, reel packing and 0-70 °C. Match the full LM324DT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists LM324N as an ACTIVE quad 30 V operational amplifier in PDIP-14, with 1.2 MHz gain bandwidth, 0 to 70 °C operation and tube factory packaging for general-purpose signal conditioning. Four amplifiers in one package is the procurement advantage: the LM324 covers most general-purpose analog stages at the lowest cost per amplifier in the industry. Selection advice: the N suffix denotes PDIP-14 through-hole — the LM324 ships in SOIC, TSSOP and other SMD packages under different suffixes, so match the full LM324N code to your assembly process. This is a 30 V part with 0–70 °C commercial range; confirm your supply rails and temperature range against the datasheet. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD4003BRMZ is an Analog Devices 18-bit, 2 MSPS successive-approximation ADC in 10-lead MSOP — for precision data acquisition that needs both speed and DC accuracy: automatic test equipment, portable instruments and machine automation. ±1 LSB maximum INL with 100.5 dB SNR and -123 dB THD at 1 kHz, no latency or pipeline delay with first conversion accurate, and a high-Z input mode plus long acquisition phase that lets low-power precision amplifiers drive it directly — no dedicated high-speed ADC driver required. Input span compression runs the driver and ADC from common rails without a negative supply. Selection advice: the BRMZ code is the MSOP-10 version — for 16-bit at lower cost the AD4000 is the family sibling; the 1.8 V single supply with 1.71–5.5 V logic interface suits battery-powered field instruments. Daisy-chainable SPI simplifies multichannel layouts. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD5689RBRUZ is an Analog Devices dual 16-bit buffered voltage-output DAC in 16-lead TSSOP — for precision setpoint and calibration outputs in industrial control: PLC I/O cards, data acquisition and optical transceiver biasing. ±2 LSB maximum INL at 16 bits, an internal 2.5 V reference with 2 ppm/°C typical drift (no external reference needed), user-selectable gain of 1 or 2 for 2.5 V or 5 V full scale, 20 mA drive capability within 0.5 V of the rails, and 50 MHz SPI with daisy-chain and readback. Power-on reset to zero or midscale keeps outputs safe at startup. Selection advice: the BRUZ code is the TSSOP-16 tube version — for single-channel designs the AD5683R is the family sibling; against the octal DAC80508 on this site, the AD5689R is the pick for dual-channel precision nodes where per-channel accuracy matters more than channel count. The 4 µA power-down mode suits battery-backed calibration circuits. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD5761RARUZ is an Analog Devices 16-bit voltage-output DAC with integrated 2.5V reference in TSSOP-16 — for industrial automation outputs where one chip must cover every standard range: PLC analog outputs, servo control and process control. Eight software-programmable output ranges (0-5V, 0-10V, 0-20V, ±3V, ±5V, ±10V and more) with 5% overrange, a ±2ppm/°C drift reference and ±2-LSB maximum INL mean the output stays accurate without external trimming. Selection advice: the ARUZ code is the TSSOP-16 reel variant — for the smaller 3x3mm LFCSP specify the ACPZ; the AD5721R is the 12-bit cost-down sibling. Single-supply 4.75V-to-30V or dual-supply operation covers both unipolar and bipolar systems — confirm your supply configuration against the range table. Asynchronous LDAC and reset-to-zero/midscale suit safety-critical outputs. Parameters verified against Analog Devices documentation and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620ARZ is a low-power instrumentation amplifier from Analog Devices in an 8-pin SOIC package, with gain set by a single external resistor — for bridge sensors, strain gauges and other small differential signals. Its advantage is the classic three-op-amp instrumentation topology in one package: high common-mode rejection with minimal external circuitry, which shortens precision front-end design. Selection advice: the ARZ suffix denotes the standard grade in SOIC-8 on tape and reel — the AD620 also ships in DIP and higher grades, so match the full code to your footprint and accuracy requirements. Gain is set by one resistor value, so confirm your gain calculation against the datasheet formula during design. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD623ARZ-R7 is an Analog Devices single-supply instrumentation amplifier, rail-to-rail output, gain 1 to 1000 set by one external resistor, 800 kHz bandwidth at G=1, in SOIC-8 — the sensor front-end amplifier for bridges, thermocouples and low-level transducer signals. The single-resistor gain programming is the selection point: no matched resistor networks to source, with 0.10% gain accuracy at G=1, 200 µV max offset and 550 µA max supply current for battery-powered instruments. Selection advice: it runs on 3 to 12 V single supply or ±2.5 to ±6 V dual supply — but note the input range extends only 150 mV below ground on a single rail, so ground-referenced bipolar sensor signals still need the dual-supply configuration. The R7 suffix is the 7-inch reel (1000 pcs) packing of the SOIC-8. For higher precision or lower noise, compare the AD620/AD8221 family rather than assuming drop-in equivalence. Parameters verified against the ADI AD623 datasheet and Mouser/LCSC listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7124-8BBCPZ is an Analog Devices 24-bit sigma-delta ADC with 8 differential (15 pseudo-differential) inputs in 32-lead LFCSP — for multichannel precision measurement where board space and power both matter: PLC/DCS analog input modules, smart transmitters and portable instrumentation. Three user-selectable power modes trade throughput against noise (down to 255 µA with 24 nV rms at gain 128), the on-chip PGA offers gains 1 to 128 with rail-to-rail inputs, and the integrated 2.5 V reference plus dual excitation current sources cut external BOM for RTD and bridge sensors. Simultaneous 50/60 Hz rejection suits noisy industrial environments. Selection advice: the BBCPZ code is the 32-lead LFCSP tray version — for 4-channel designs the AD7124-4 is the pin-family sibling; the per-channel programmable digital filters let one hardware platform serve both fast and high-resolution channels. The on-chip diagnostics aid functional-safety designs. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7190BRUZ is an Analog Devices 24-bit sigma-delta ADC with internal PGA in 24-lead TSSOP — the established weigh-scale and strain-gauge front end: the CN0102 reference design builds a complete precision weigh scale around it with only input filters added. Ultralow-noise performance from 4.7 Hz to 4.8 kHz output data rates covers both slow precision and faster hopper-scale applications, the internal PGA interfaces load cells directly, and the bridge power-down switch minimizes system power. On-chip temperature sensor and burnout detection complete the transducer interface. Selection advice: the BRUZ code is the TSSOP-24 tube version (-40 to +105 °C) — for 8-channel multiplexed weigh systems step up to the AD7124-8 on this site; the AD7190 stays the pick for dedicated single-bridge precision channels. Match the full BRUZ code for package and temperature grade. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8422BRZ is an Analog Devices rail-to-rail instrumentation amplifier in SOIC-8 — for bridge sensors, strain gauges and low-level differential signals where a discrete op-amp network drifts with temperature and layout. Gain is set by a single external resistor from 1 to 1000, with 25µV maximum input offset, 2.2MHz bandwidth and 150dB CMRR at high gain — precision front-end performance with minimal external circuitry. Selection advice: the BRZ code is the B grade (tighter offset than the A grade) in SOIC-8 tube packing — for reel packing specify the BRZ-R7; the MSOP-8 BRMZ suits tighter layouts. At 300µA supply current it fits battery-powered instruments, but confirm the 4.6V-to-36V supply span against your rails — for single 3.3V-only systems check the input range limits. For higher bandwidth or lower noise, compare the AD8421/AD8429 family rather than assuming interchangeability. Parameters verified against Analog Devices documentation and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.