6N137

TLP2362 is a Toshiba 10MBd high-speed photocoupler in 6-pin SO6 — for isolated digital interfaces where speed and noise immunity matter: PLC I/O modules, measuring instruments and factory automation controllers. A high-output infrared LED coupled to integrated high-gain photodetectors delivers 10MBd (typ.) data rates on 2.7V to 5.5V supplies, with an internal Faraday shield guaranteeing ±20kV/µs common-mode transient immunity and 3750Vrms isolation. -40°C to +125°C operation suits hot industrial enclosures. Selection advice: the inverter-logic open-collector output needs a pull-up resistor — for totem-pole outputs consider a different logic-output coupler; the 5.0mA max threshold input current is higher than the low-input TLP293 family on this site, so match the drive capability of your isolating MCU pin. The SO6 package saves board space versus DIP optocouplers. Parameters verified against Toshiba documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS1302+ is an Analog Devices (Maxim) trickle-charge serial real-time clock with 3-wire interface in DIP-8 — for basic timekeeping with battery backup: appliances, simple controllers and legacy designs. The trickle-charge circuit is the selection point: it recharges the backup cell from VCC, extending field life. Selection advice: the + denotes the lead-free DIP-8 — pick the DS1302 for 3-wire serial interfaces; for I2C designs the DS1307 is the sibling; for accuracy without calibration, the DS3231's integrated TCXO is the step up. External 32.768 kHz crystal required. Parameters verified against the ADI official datasheet ordering table. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS1307+ is an Analog Devices (Maxim) I2C real-time clock with 56 bytes of battery-backed NV SRAM in DIP-8 — for basic timekeeping in cost-sensitive designs: appliances, toys and simple controllers. The rock-bottom price and DIP package is the selection point: timekeeping for breadboards and hand assembly. Selection advice: the + denotes the lead-free DIP-8 — pick the DS1307 when basic timekeeping suffices; for accuracy without calibration, the DS3231's integrated TCXO is the step up. Note the external 32.768 kHz crystal is required and 4.5–5.5 V supply only. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

1ED020I12-F2 is an Infineon EiceDRIVER single-channel high-side IGBT gate driver in PG-DSO-16, tape and reel — 1200 V voltage class, ±2 A rail-to-rail output, coreless-transformer galvanic isolation, desaturation/short-circuit protection, active Miller clamp, active shutdown, UVLO on both supplies, 170 ns turn-on / 165 ns turn-off propagation delay, industrial qualified. The DESAT plus active Miller clamp combination is the selection point: a shorted IGBT is detected and shut down in hardware before the die fails, and the clamp holds the gate off against parasitic turn-on — a plain optocoupler gate drive provides neither. Selection advice: the full orderable code is 1ED020I12F2XUMA1 where XUMA1 denotes tape and reel (1,000 per reel); the 1ED020I12-B2 is the isolated variant in the same family and the 2ED020I12-F2 the dual-channel high-side version. Infineon lists this part Active, DigiKey lists the full code as in stock, and Infineon community support names it the recommended replacement for the discontinued 1ED020I12-FA. Evidence: the Infineon official datasheet Rev. 2.1 and product page confirm the ordering code, 1200 V class, ±2 A output, DSO-16 package and Active status. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

1EDN7511B is an Infineon EiceDRIVER single-channel low-side gate driver in PG-SOT23-6, tape and reel — for driving power MOSFETs from logic in compact SMPS stages. 4 A source / 8 A sink with 3.9 V UVLO is the selection point: asymmetric drive with logic-compatible turn-on threshold. Selection advice: the B suffix denotes the SOT-23-6 package — for the higher-UVLO variant suited to noisy rails, the 1EDN8511B is the sibling; the 4.2 V to 20 V range suits both 5 V and 12 V drive rails. Infineon lists this part as Active and preferred. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

1EDN8511B is an Infineon EiceDRIVER single-channel low-side gate driver in PG-SOT23-6, tape and reel — for driving power MOSFETs from logic in compact SMPS stages. 4 A source / 8 A sink with 7 V UVLO is the selection point: asymmetric drive with a higher turn-on threshold for noisy gate-drive rails. Selection advice: the B suffix denotes the SOT-23-6 package; the 8 V to 20 V range versus the 4.2 V to 20 V of the 1EDN7511B — pick this variant where a higher UVLO better rejects supply noise. Infineon lists this part as Active and preferred. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

23LC1024-I/P is a Microchip 1-Mbit SPI serial SRAM in 8-pin PDIP — for fast scratchpad memory: data buffering, display framebuffers and audio delay lines. Unlimited read/write endurance at up to 20 MHz SPI is the selection point: RAM speed with none of EEPROM's write-cycle limits. Selection advice: the I/P denotes PDIP-8 — the breadboard-friendly variant; for SMT, the SOIC variant is the pick. Volatile — for non-volatile needs, the 24LC EEPROM series is the sibling; for more speed, the SQI mode doubles throughput. Microchip lists this part as In Production. Parameters verified against the Microchip official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

24LC256-I/P is a Microchip 256 Kbit I2C serial EEPROM in 8-pin PDIP — for non-volatile storage: configuration data, calibration tables and event logs. 256 Kbit with 1M erase/write cycles is the selection point: the workhorse EEPROM density for embedded designs. Selection advice: the I/P denotes PDIP-8 — the breadboard-friendly variant; for SMT, the SOIC variant is the pick. 64-byte page writes and 400 kHz bus cover most logging needs; for larger storage, step up the 24LC series density. Microchip lists this part as In Production. Parameters verified against the Microchip official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

2EDF7235K is an Infineon EiceDRIVER dual-channel isolated gate driver — PG-TFLGA-13, functional galvanic isolation, tape and reel. The coreless-transformer isolation is the selection point: dual-channel isolated drive in a 5×5 mm package with no optocoupler aging — for SiC/GaN and IGBT stages. Selection advice: lifecycle warning — Infineon lists the 2EDF7235K as discontinued (EOL announced May 2023); for new designs migrate to the current-generation 2EDF7xxx family, and for repairs and legacy builds we source remaining stock. Confirm the exact 2EDF7235K code on the BOM — the EiceDRIVER family spans many current and package variants that are not interchangeable. Evidence: Infineon data confirms discontinued status and the base ordering code. Match the full 2EDF7235K code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

2EDF7275F is an Infineon EiceDRIVER dual-channel isolated half-bridge gate driver — PG-DSO-16, 4 A source / 8 A sink, functional galvanic isolation, UVLO 3.9 V/4.2 V, tape and reel. The 4 A/8 A asymmetric drive is the selection point: strong turn-off for fast switching in a standard DSO-16 — isolated drive without an optocoupler. Selection advice: lifecycle note — Infineon lists the 2EDF7275F as Not For New Design; for new designs specify the 2EDF7275K (the Active/preferred TFLGA-13 variant of the same die), and for existing production confirm the exact 2EDF7275F code — the K and F suffixes are different packages and are not interchangeable. Verify the functional (not reinforced) isolation rating against your safety standard. Evidence: Infineon data confirms NFND, DSO-16, 4 A/8 A, functional isolation, UVLO levels. Match the full 2EDF7275F code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.