TXS0102DQMR

TXS0102DCTR is a Texas Instruments TXS0102 2-bit bidirectional voltage-level translator in SSOP-8, 3000-piece tape and reel — VCCA 1.65 V to 3.6 V, VCCB 2.3 V to 5.5 V (VCCA at or below VCCB), automatic direction sensing with no direction pin, OE enable referenced to VCCA, works with open-drain and push-pull signals, −40 °C to +85 °C. The DCTR code is the selection point: the SSOP-8 package on 3000-piece reel — the production-volume code for mixed-voltage UART, SPI and GPIO interfaces. Selection advice: the auto-direction sensing is why the TXS0102 wins over direction-controlled translators — no GPIO wasted on a DIR pin, which matters on pin-constrained MCUs. It handles both open-drain (I2C-style) and push-pull, but for heavily loaded I2C buses check the rise-time requirements against a dedicated I2C translator. For prototypes use the 250-piece DCTT; for smaller footprints use the DCU/DQM/DTT codes. Evidence: TI TXS0102 datasheet confirms SSOP-8 (DCT), 3000-piece reel, VCCA/VCCB ranges and −40 to +85 °C. Match the full TXS0102DCTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TXS0102DCTT is a Texas Instruments TXS0102 2-bit bidirectional voltage-level translator in SSOP-8, 250-piece small reel — VCCA 1.65 V to 3.6 V, VCCB 2.3 V to 5.5 V (VCCA at or below VCCB), automatic direction sensing with no direction pin, OE enable referenced to VCCA, works with open-drain and push-pull signals, −40 °C to +85 °C. The DCTT code is the selection point: the same SSOP-8 die as the DCTR, but on 250-piece reel — prototypes, pilot runs and repairs get the auto-sensing translator without a 3000-piece reel commitment. Selection advice: the T versus R suffix is purely a packing choice — same SSOP-8 footprint, same silicon, so a design proven on the DCTT moves to the DCTR for volume with no requalification. The 1.65 V VCCA floor covers 1.8 V logic directly, and the 5.5 V VCCB ceiling covers 5 V legacy peripherals. Evidence: TI TXS0102 datasheet package addendum confirms SSOP-8 (DCT), 250-piece reel and the VCCA/VCCB ranges. Match the full TXS0102DCTT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TXS0102DCUR is a Texas Instruments TXS0102 2-bit bidirectional voltage-level translator in VSSOP-8, 3000-piece tape and reel — VCCA 1.65 V to 3.6 V, VCCB 2.3 V to 5.5 V (VCCA at or below VCCB), automatic direction sensing with no direction pin, OE enable referenced to VCCA, works with open-drain and push-pull signals, −40 °C to +85 °C. The DCUR code is the selection point: the VSSOP-8 package on 3000-piece reel — the compact production code, roughly half the footprint of SSOP-8, for dense mixed-voltage boards. Selection advice: pick the DCU package when board area is tight and the assembly flow is all-SMD; pick the SSOP DCT codes when the slightly larger package eases inspection and rework. Electrically identical — same auto-sensing, same voltage ranges — so the choice is purely mechanical. For prototypes use the 250-piece DCUT. Evidence: TI TXS0102 datasheet confirms VSSOP-8 (DCU), 3000-piece reel and the VCCA/VCCB ranges. Match the full TXS0102DCUR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TXS0102DCUT is a Texas Instruments TXS0102 2-bit bidirectional voltage-level translator in VSSOP-8, 250-piece small reel — VCCA 1.65 V to 3.6 V, VCCB 2.3 V to 5.5 V (VCCA at or below VCCB), automatic direction sensing with no direction pin, OE enable referenced to VCCA, works with open-drain and push-pull signals, −40 °C to +85 °C. The DCUT code is the selection point: the VSSOP-8 die on 250-piece reel — the compact prototype code for proving a mixed-voltage interface before volume. Selection advice: qualify the level-shifting design on the DCUT, then move to the 3000-piece DCUR for production with zero layout change — same VSSOP-8 drawing, same pinout. The auto-sensing architecture means neither firmware nor a direction GPIO is needed, which simplifies bring-up on both sides of the voltage boundary. Evidence: TI TXS0102 datasheet package addendum confirms VSSOP-8 (DCU), 250-piece reel and the VCCA/VCCB ranges. Match the full TXS0102DCUT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TXS0102DTTR is a Texas Instruments TXS0102 2-bit bidirectional voltage-level translator in X1SON-8, 5000-piece tape and reel — VCCA 1.65 V to 3.6 V, VCCB 2.3 V to 5.5 V (VCCA at or below VCCB), automatic direction sensing with no direction pin, OE enable referenced to VCCA, works with open-drain and push-pull signals, −40 °C to +85 °C. The DTTR code is the selection point: the 1 × 1 mm X1SON package on 5000-piece reel — the absolute smallest, highest-volume order code in the TXS0102 family, for level shifting inside modules and chip-scale designs. Selection advice: pick the DTTR only when the assembly flow is proven for 1 × 1 mm leadless parts — inspection and rework are essentially impossible by hand, so keep a VSSOP DCU code as the bring-up alternate on the same schematic. The 5000-piece reel is the deepest-volume packing TI offers here. Evidence: TI carrier material report for TXS0102DTTR confirms X1SON-8 (DTT), 5000-piece reel. Match the full TXS0102DTTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TXS0102YZPR is a Texas Instruments TXS0102 2-bit bidirectional voltage-level translator in DSBGA-8, 3000-piece tape and reel — VCCA 1.65 V to 3.6 V, VCCB 2.3 V to 5.5 V (VCCA at or below VCCB), automatic direction sensing with no direction pin, OE enable referenced to VCCA, works with open-drain and push-pull signals, −40 °C to +85 °C. The YZPR code is the selection point: the chip-scale DSBGA-8 package on 3000-piece reel — the wafer-level option for the TXS0102 inside modules and SiP designs where even X2SON is too big. Selection advice: pick the DSBGA only when the assembly flow is proven for 0.4 mm-pitch wafer-level packages — no rework, no inspection by hand; keep a VSSOP DCU code as the debug alternate. Electrically the same auto-sensing translator as every other TXS0102 code — 1.65 V to 5.5 V coverage, no direction GPIO needed. Evidence: TI TXS0102 datasheet confirms DSBGA-8 (YZP), 3000-piece reel and the VCCA/VCCB ranges. Match the full TXS0102YZPR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TXS0102DQER is a Texas Instruments 2-bit bidirectional voltage-level translator in X2SON-8, tape and reel — for I2C, UART and GPIO between mixed-voltage domains: 1.8 V sensors talking to 3.3 V MCUs, or 5 V legacy peripherals. No direction-control signal needed is the selection point: the chip auto-detects direction, saving GPIO pins and firmware. Selection advice: the R suffix denotes tape and reel; the A port covers 1.65 V to 3.6 V and the B port 2.3 V to 5.5 V, with VCCA at or below VCCB — keep this ordering or translation fails. 24 Mbps push-pull and 2 Mbps open-drain cover I2C and UART; the 1.45 × 1 mm X2SON suits dense boards. −40 °C to +85 °C. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83848IVVX/NOPB is a Texas Instruments DP83848I industrial-temperature 10/100 Mbps Ethernet PHY transceiver — 48-pin LQFP (7 × 7 mm), MII/RMII/SNI MAC interfaces, auto-MDIX, energy-detect mode, JTAG, 3.3 V, tape-and-reel packing of 1000, -40 to +85 °C. The industrial temperature range is the selection point: the I grade covers factory automation and outdoor equipment where commercial-grade PHYs fail, with auto-MDIX eliminating crossover-cable concerns. Selection advice: this is a PHY only — it needs an external MAC (MCU or switch) and a magnetics module. The V suffix is the 48-LQFP package; NOPB is the lead-free RoHS variant. For Gigabit Ethernet choose a different PHY family, since this is strictly 10/100. TI lists this code as Active. Evidence: TI DP83848I datasheet and distributor listings confirm 10/100 Mbps PHY, 48-LQFP, MII/RMII, -40 to +85 °C and 1000/reel packing. Match the full DP83848IVVX/NOPB code for temperature grade and package. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83867ERGZR is a Texas Instruments 10/100/1000BASE-T Gigabit Ethernet PHY in 48-pin VQFN (7x7mm) — for industrial Ethernet nodes where deterministic latency and diagnostics matter: PLCs, machine vision cameras and grid automation. RGMII and SGMII MAC interfaces, IEEE 1588 start-of-frame detection for time-sensitive networking, cable diagnostics, and 8kV IEC 61000-4-2 ESD protection. Selection advice: the E variant covers -40 to +105°C — for commercial 0 to +70°C the CS code costs less, and the IR code targets -40 to +85°C industrial; for 10/100 Mbps only the DP83848 on this site is the economical choice. 457mW full-power draw suits fanless enclosures. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83TC812RRHARQ1 is a Texas Instruments AEC-Q100 Grade 1 100BASE-T1 automotive Ethernet PHY in 36-pin VQFN (6x6mm) — for zonal E/E architectures replacing CAN with Ethernet: zone controllers, ADAS sensor fusion and infotainment backbones. IEEE 802.3bw compliant, TC-10 sleep/wake under 20µA, integrated low-pass filter passing Level IV emissions, and MII/RMII/RGMII MAC interfaces with 1.8V/2.5V/3.3V I/O. Heat evidence: automotive Ethernet is the fastest-growing in-vehicle networking segment — OEMs are shifting from domain to zonal architectures, and 100BASE-T1 is the volume PHY for camera/radar links. Selection advice: the R variant includes RGMII — for SGMII-only designs the S variant costs less; the integrated LPF eliminates external magnetics filtering. AEC-Q100 Grade 1 (-40 to +125°C) with ±8kV IEC ESD on MDI pins. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.