MIC28517T-E/PHA

LM5164DDAR is a Texas Instruments 100 V input synchronous buck converter in SOIC-8, tape and reel — for industrial power supplies: 48 V bus step-down, PoE front ends and motor-drive auxiliaries. The 100 V input rating is the selection point: direct operation from high-voltage industrial buses that standard 60 V bucks cannot survive. Selection advice: the DDAR suffix denotes SOIC-8 in tape and reel for production — plan the external MOSFET, inductor and compensation network per TI's reference design; this is a controller-class part, not a module. For lower-voltage rails, cheaper integrated bucks save board space. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MP9943GQ-Z is a Monolithic Power Systems 3 A synchronous step-down converter, 4 to 36 V input, adjustable output from 0.8 V (792 mV feedback reference), 410 kHz, in a QFN-8 (3 × 3 mm) package — a compact point-of-load regulator for set-top boxes, networking gear and industrial modules. The synchronous architecture is the selection point: integrated high-side and low-side MOSFETs eliminate the external Schottky diode that non-synchronous bucks like the TPS5430 require, cutting BOM count and improving light-to-mid-load efficiency in the same 3 A class. Selection advice: the -Z suffix is MPS tape-and-reel packing (-P is tray/tube), so match the suffix to your assembly line; the EN pin gives simple sequencing/shutdown, the PG output supports power-good monitoring, and the SYNC pin accepts 200 kHz to 2.4 MHz external clocking for EMI-sensitive designs. Rated -40 to +125 °C junction. Do not confuse with the MP9943A variant (different feature set) — verify the exact MP9943GQ-Z code on the MPS datasheet. Parameters verified against the MPS MP9943 datasheet (Rev. 1.1) and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TLV62568DBVR is a Texas Instruments 1 A synchronous step-down buck converter in SOT-23-5 (DBV), tape-and-reel packing (R) — 2.5 V to 5.5 V input, adjustable output from 0.6 V up to VIN, up to 95% efficiency, 35 µA operating quiescent current, 1.5 MHz typical switching frequency, power-save mode for light-load efficiency, 100% duty cycle for lowest dropout, internal soft start, overcurrent and thermal-shutdown protection, −40 to +125 °C. The adjustable output with 100% duty cycle is the selection point: one part generates 1.2 V, 1.8 V, 3.3 V or any logic rail from a 5 V or Li-ion source with near-zero dropout, so the same footprint covers multiple rails across a board — a general-purpose point-of-load workhorse for set-top boxes, cameras, routers and disk drives. Selection advice: the DBV is the 5-pin SOT-23; the R suffix is tape and reel. The adjustable TLV62568 covers what the fixed-output members of the family do plus any custom rail — confirm the exact fixed-output code only if the BOM specifies one. TI lists TLV62568DBVR as Active. Evidence: TI TLV62568 datasheet (SLVSD89) and distributor listings confirm 1 A, 2.5–5.5 V, 0.6 V to VIN, SOT-23-5 and tape-and-reel packing. Match the full TLV62568DBVR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TPS54302DDCR is a Texas Instruments 3 A synchronous buck converter in SOT-23-6, tape and reel — for compact point-of-load power: set-top boxes, printers and industrial I/O modules. 3 A from a SOT-23-6 is the selection point: unusual current density for general-purpose rails. Selection advice: the DDCR suffix denotes SOT-23-6 in tape and reel for production — follow TI's layout guidance closely, as thermal performance in this package depends on copper area; for higher currents, larger-package bucks are the step up. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TPS560430XDBVR is a Texas Instruments 36V, 4A synchronous buck converter — for industrial and automotive power rails: 4A continuous output current, up to 36V input, synchronous rectification for high efficiency, SOT-23-6 package. The synchronous topology eliminates the external Schottky diode, so efficiency stays high across the load range while the BOM shrinks; the 36V input rating tolerates 24V industrial buses with margin for transients. Business impact: compact high-current bucks are the default choice for point-of-load regulation — the SOT-23-6 footprint fits where larger packages cannot, and TI availability keeps lead times manageable. Selection advice: the XDBVR code denotes SOT-23-6 on tape and reel — verify the switching frequency and compensation against the TI datasheet for your specific input/output combination. Ranked #11 on the hqbuy.com real-time hot list (2026-10-05). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TPS56221DQPR is a Texas Instruments 25A synchronous buck converter — for high-current point-of-load supplies: 4.5V to 14V input, output down to 0.6V at up to 25A, integrated NexFET power MOSFETs, fixed-frequency options of 300kHz, 500kHz and 1MHz, voltage-mode control with feed-forward, 600mV reference with 1% accuracy, programmable soft start, resistor-programmed overcurrent protection, thermal shutdown, 22-pin 5x6mm PQFN PowerPAD package. The integrated NexFET power block delivers 25A from a 30mm² footprint, so FPGA and processor core rails fit tight board areas; feed-forward compensation responds instantly to input voltage changes. Business impact: high-current POL converters are critical-path components in server and telecom designs — a stocked, well-documented part accelerates power-tree qualification. Selection advice: the DQPR code is the PQFN-22 package in tape and reel — verify the overcurrent protection programming resistor and loop compensation against the TI datasheet for the target load transient. Featured on hqbuy.com hot search (2026-09-28). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP1700-3302E/TO is a Microchip 3.3 V 250 mA CMOS LDO in TO-92-3 — for battery and IoT: 1.6 µA typical quiescent current, 2.3–6 V input, -40°C to +125°C. The ultra-low quiescent current is the selection point: years of standby on coin cells where a standard LDO would drain the battery. Selection advice: the /TO code is the TO-92 through-hole — for SMT use the SOT-23 or SOT-89 variants; the 250 mA rating suits sensor nodes, not power-hungry radios. Parameters verified against Microchip documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP1700T-2502E/TT is a Microchip MCP1700 fixed 2.5 V CMOS low-dropout linear regulator — 250 mA, 1.6 µA typical quiescent current, in SOT-23-3, tape-and-reel packing (T), extended temperature -40 to +125 °C (E). The 1.6 µA quiescent current with 178 mV typical dropout at 250 mA is the selection point: an always-on 2.5 V rail that sips battery instead of draining it, stable with just 1 µF of ceramic output capacitance. Selection advice: the 2.3 V minimum input is the feature to exploit — this part runs a 2.5 V rail from a single Li-ion cell down to near-empty or from two alkaline cells, where regulators with higher minimum inputs give up early. Short-circuit and overtemperature protection are built in, and ±0.4% typical tolerance suits voltage-reference-adjacent jobs. The TT code is the SOT-23-3 package on reel; for 5.0 V rails use MCP1700T-5002E/TT, not this 2.5 V code. Evidence: Microchip MCP1700 datasheet (DS20001826) and distributor listings confirm 2.5 V, 250 mA, 1.6 µA quiescent, 2.3-6.0 V input and SOT-23-3. Match the full MCP1700T-2502E/TT code for voltage, temperature grade and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP1700T-3302E/TT is a Microchip 3.3 V fixed low-dropout regulator in SOT-23-3, tape and reel — for battery-powered 3.3 V rails: sensors, MCUs and smoke/CO detectors. 1.6 µA quiescent current with 178 mV dropout at 250 mA is the selection point: minimal battery drain in sleep plus low headroom. Selection advice: the 3302 code denotes the 3.3 V fixed output — the MCP1700 family covers 1.2 V to 5.0 V fixed options, match the code to your rail; the T suffix denotes tape and reel; 250 mA suits light loads — for heavier loads or adjustable output, step up to a larger LDO family. 2.3 V to 6 V input. Microchip lists this part as Active. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MCP1700T-5002E/TT is a Microchip MCP1700 fixed 5.0 V CMOS low-dropout linear regulator — 250 mA, 1.6 µA typical quiescent current, in SOT-23-3, tape-and-reel packing (T), extended temperature -40 to +125 °C (E). The 1.6 µA quiescent current is the selection point: a 5 V always-on rail for sleep-dominated, battery-backed systems that cannot afford a regulator with milliamp housekeeping current. Selection advice: mind the tight input window — the 6.0 V maximum input with roughly 178 mV dropout means the supply must sit between about 5.2 V and 6.0 V, so this code suits 4×AA packs or pre-regulated 6 V rails, not 5 V USB (no headroom) and not 12 V buses (overvoltage and, at 250 mA, over 1.5 W to dissipate in a SOT-23). For high-drop or high-current 5 V rails, use a buck converter instead of any linear regulator. Stable with 1 µF ceramic output capacitance, with short-circuit and overtemperature protection built in. Evidence: Microchip MCP1700 datasheet (DS20001826) and distributor listings confirm 5.0 V, 250 mA, 1.6 µA quiescent, 2.3-6.0 V input and SOT-23-3. Match the full MCP1700T-5002E/TT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Microchip and Navitas showed an 800V-to-6V GaN reference design for AI racks, targeting 96% efficiency. What the design actually is, what it signals for component selection, and a five-point buyer checklist.