TLV9002IDGKR

LMV358IDR is a Texas Instruments dual low-voltage operational amplifier in 8-pin SOIC — the 5 V-and-below workhorse for cost-sensitive signal conditioning: appliance controls, HVAC boards and portable instruments. 2.7 V to 5.5 V supply, 1 MHz gain bandwidth, rail-to-rail output swing, 210 µA typical supply current per channel, -40 to +125 °C operation. The low-voltage design is the selection point over the classic LM358: full specified performance at 3.3 V and 5 V single supplies where the LM358 is out of its comfort zone, with no crossover distortion. Selection advice: this is the low-voltage sibling of the LM358 on this site — pick the LMV358 for 3.3 V/5 V-only designs; keep the LM358 when the rail goes above 5.5 V or below ground sensing matters. The IDR code is the 2500-reel SOIC. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Microchip lists MCP6002-I/P as In Production — a dual 1 MHz rail-to-rail op amp, 1000 kHz gain-bandwidth, max 170 µA quiescent current, PDIP-8 tube packaging. Rail-to-rail input and output is the selection point for single-supply designs: the full signal swing is usable on low-voltage rails where a classic LM358 would clip. Selection advice: the I/P suffix denotes the industrial temperature grade in PDIP-8 — the MCP6002 ships in several grades and SMD packages, so match the full code. At 170 µA quiescent current it suits battery-powered signal chains; confirm your bandwidth need against the 1 MHz GBW. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM358DGKR is a Texas Instruments LM358 dual operational amplifier — the industry-standard general-purpose op-amp, 3 to 32 V single supply (±1.5 to ±16 V dual), internally frequency-compensated, in 8-pin VSSOP, tape-and-reel packing of 2500 (DGKR), 0 to +70 °C commercial grade. Single-supply operation with the common-mode range including ground is the selection point: it runs directly from one 5 V or 3.3 V rail for transducer amplifiers, DC gain blocks and comparator circuits without a negative supply. Selection advice: the output swings to about Vcc - 1.5 V — it is not rail-to-rail, so for full-swing output choose a CMOS rail-to-rail family (TLV or OPA series) instead. This DGKR code is the small VSSOP package on reel; the same die is available in SOIC, TSSOP and PDIP for hand-soldering or legacy layouts. The 0-70 °C range marks it as commercial grade — for industrial or automotive temperature ranges choose the LM2904 family. Evidence: TI LM358 datasheet and distributor listings confirm 3-32 V supply, dual channel, VSSOP-8 and 2500-reel packing. Match the full LM358DGKR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

THS4121IDGNR is a Texas Instruments fully-differential amplifier — for single-ended to differential conversion and ADC driving: 100MHz -3dB bandwidth, 50V/µs slew rate, -75dB total harmonic distortion at 1MHz, 5.4nV/√Hz input-referred noise, differential input and output, 3.3V supply, 8-pin VSSOP package. The fully-differential signal path from input to output rejects common-mode noise and improves distortion, so high-speed ADCs get the clean drive they need without extra filtering stages. Business impact: differential ADC drivers are the bottleneck component in precision data-acquisition front ends — a catalog-standard part with long availability simplifies qualification and second sourcing. Selection advice: the DGNR code is the VSSOP-8 package — for MSOP with PowerPAD consider the DGK variant; the THS4121 is the no-power-down member — for shutdown capability consider the THS4120. Ranked #15 on the hqbuy.com real-time hot list (2026-09-28). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists ADS1115IDGSR as an ACTIVE 16-bit delta-sigma ADC in VSSOP-10, with 860 SPS sampling, 4 multiplexed channels and I2C interface. The 16-bit resolution is the procurement-relevant advantage: it resolves small sensor signals that a 10- or 12-bit converter would bury in quantization noise, which is why this part is the default choice for precision data-acquisition front ends. Selection advice: the IDGSR suffix pins the VSSOP-10 package on tape and reel — the ADS1115 also ships in other packages, so match the full code to your layout. Four multiplexed inputs versus the two-channel ADS1113 and single-ended/differential options are the family decision points; confirm your channel count and interface (I2C here, not SPI) against the datasheet before substituting. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDGST is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter — four single-ended or two differential inputs, programmable gain amplifier with full-scale ranges from ±6.144 V down to ±0.256 V, programmable data rates from 8 to 860 SPS, I2C interface with four pin-selectable addresses, in 10-pin VSSOP, tube packing (DGST), -40 to +125 °C. The integrated PGA, low-drift reference and oscillator are the selection point: true precision ADC performance with no external reference or clock, ideal for battery-voltage monitoring, temperature measurement and portable instrumentation. Selection advice: 860 SPS suits slow precision signals — for kilohertz sampling choose an SAR ADC (ADS868x family) instead. The built-in comparator can drive an alert pin for threshold monitoring without MCU polling, and 16 I2C addresses (four pins × four states) let you run multiple converters on one bus. Note this exact ADS1115IDGST code is the tube variant; IDGSR is the reel version. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA ranges, 8-860 SPS, VSSOP-10 and tube packing. Match the full ADS1115IDGST code for packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDYNR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin SOT-23 package — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing (DYNR), -40 to +125 °C. The SOT-23 footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in the smallest ADS1115 package for space-constrained sensor nodes. Selection advice: same die and performance as the VSSOP (IDGST) and X2QFN (IRUGR) variants — choose this code for the SOT-23 footprint and reel packing. The 150 µA active current and single-shot power-down mode suit battery designs; for 24-bit resolution or excitation sources step up to the ADS1220. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA, I2C, SOT-23-10 and reel packing. Match the full ADS1115IDYNR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin X2QFN package (2 × 1.5 × 0.4 mm) — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing of 3000 (IRUGR; IRUGT is the small reel), -40 to +125 °C. The 2 × 1.5 mm footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in one of the smallest ADC packages available, for wearables and dense sensor boards. Selection advice: same die and performance as the VSSOP (IDGSR) and SOT-23 (IDYNR) variants — choose this code for the X2QFN footprint and 3000-reel packing. Leadless QFN needs reflow assembly and good layout practice; for hand-soldering prototypes choose the VSSOP variant. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D), TI pack addendum and DigiKey listings confirm 16-bit, PGA, I2C, X2QFN-10 and 3000-reel packing. Match the full ADS1115IRUGR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGT is a Texas Instruments 16-bit delta-sigma ADC in 10-pin X2QFN (2.0 × 1.5 × 0.4 mm), 250-piece small reel — I2C interface, four single-ended or two differential inputs, programmable gain amplifier (±256 mV to ±6.144 V), internal low-drift reference and oscillator, programmable comparator, 8 to 860 SPS, 2.0–5.5 V, 150 µA, −40 °C to +125 °C. The integration is the selection point: PGA, MUX, reference, oscillator and comparator on one 2×1.5 mm die means a complete sensor front end with no external analog support chips. Selection advice: the RUG package code is the X2QFN — ADS1115IDGST is the same die in VSSOP-10 on 250-piece small reel — the easier-to-assemble alternative for designs that do not need the 2×1.5 mm X2QFN footprint, not interchangeable on the same footprint. Against the 12-bit ADS1015: pick the ADS1115 for resolution (weighing, precision sensing), the ADS1015 for speed (3300 SPS). The ADDR pin gives four I2C addresses, so up to four devices share one bus. Evidence: TI ADS1115 datasheet (ordering addendum) and distributor listings confirm X2QFN-10, 250-reel, 16-bit, I2C and −40 to +125 °C. Match the full ADS1115IRUGT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1220IPW is a Texas Instruments ADS1220 24-bit delta-sigma analog-to-digital converter for small-signal sensors — programmable gain from 1 to 128 V/V, up to 2000 SPS with single-cycle settling, SPI-compatible interface, in 16-pin TSSOP, tube packing (IPW; IPWR is the reel version), -40 to +125 °C. The two programmable excitation current sources plus simultaneous 50/60 Hz rejection at 20 SPS are the selection point: complete RTD, thermocouple, bridge-sensor and weigh-scale front ends with no external current source or mains-noise filtering. Selection advice: 20-bit effective resolution suits precision instrumentation — for kilohertz sampling choose an SAR ADC instead. The internal 2.048 V reference, oscillator and temperature sensor cut the external BOM to near zero; for I2C instead of SPI choose the ADS1115 family. TI lists this code as Active. Evidence: TI ADS1220 datasheet (SBAS501D) and TI pack addendum confirm 24-bit, PGA 1-128, 2 kSPS, TSSOP-16 and tube packing. Match the full ADS1220IPW code for packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.