MAX98357A

LM386N-1/NOPB is a Texas Instruments 700 mW mono AB-class audio power amplifier, 5–18 V supply, in 8-pin PDIP — for small speakers: intercoms, toys and portable radios. The minimal external parts (gain set by one capacitor) is the selection point: audio output with almost no support circuitry. Selection advice: the N-1/NOPB is the current orderable code — the bare LM386N-1 suffix is obsolete, so always order the /NOPB; for higher power or stereo, modern Class-D amplifiers are far more efficient. TI lists this order code as Active. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TAS2564 is a Texas Instruments 7-W digital-input Class-D smart amplifier in 36-ball DSBGA — for smartphones, wireless speakers and portable devices where the speaker must play louder without damage: integrated 13-V Class-H boost (256-level, algorithmically controlled), real-time speaker voltage/current sense for excursion and thermal protection, 110-dB SNR, I2S/TDM plus I2C with MCLK-free operation. Battery-tracking peak limiter with brownout prevention holds headroom across the full discharge curve; up to four devices share one bus. Selection advice: this is the integrated-boost smart amp — for external-boost designs the TAS2770 in QFN is easier to assemble than the 0.4-mm-pitch DSBGA; against the non-boost MAX98357A on this site, the TAS2564 plays markedly louder from the same battery at higher system cost. Configure via PurePath Console GUI. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TAS5805M is a Texas Instruments 23-W digital-input stereo Class-D amplifier in 32-pin HTSSOP — for smart speakers, soundbars and IoT audio where the amplifier must also do the audio processing: I2S/TDM digital input, integrated 96-kHz audio DSP with 15 biquads per channel, 3-band DRC, volume, mixing and level metering. Closed-loop architecture needs only 8 passives versus 31 for open-loop designs, and inductorless operation (ferrite bead) up to 10 W/ch shrinks the board. Selection advice: this is the DSP-equipped upgrade path from TAS5707/TAS5733L/TAS5751M per TI transition guide — for higher 35-W output the pin-different TAS5822M is the step up; for analog-input designs without DSP the TPA3116D2 on this site costs less. 16.5-mA quiescent at 13.5 V suits battery-powered portable speakers. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TAS6424Q1 is a Texas Instruments AEC-Q100 automotive 4-channel Class-D audio amplifier — for premium in-vehicle infotainment: head units, external amplifiers and sound systems. Four bridge-tied-load channels with up to 2.1MHz switching frequency, AC diagnostics for tweeter open/short detection with impedance measurement, and CISPR25 Level 5 EMC compliance. Heat evidence: automotive audio is moving to fully digital Class-D as OEMs chase efficiency and diagnostic coverage — tweeter diagnostics are now a checklist item for premium trims. Selection advice: the 4-channel BTL configuration suits standard 4-speaker systems — for subwoofer drive the parallel-BTL mode doubles current; the 2.1MHz switching keeps AM-band interference out. AEC-Q100 qualified for automotive. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TDA7294V is a DMOS audio power amplifier from STMicroelectronics in a Multiwatt-15 package, for high-fidelity audio applications — Hi-Fi amplifiers, active speakers and car audio. Its advantage is the DMOS output stage: high output current with built-in thermal shutdown and short-circuit protection, which keeps a high-power audio design robust without elaborate discrete protection. Selection advice: the V suffix denotes the Multiwatt-15 vertical package — board mounting and heatsinking are integral to this part, so follow the datasheet mechanical and thermal guidance. High-power audio layouts are sensitive to grounding and supply decoupling; confirm your PCB follows the reference design. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TPA3116D2 is a Texas Instruments 50-W stereo Class-D audio amplifier in 32-pin HTSSOP — for powered speakers, soundbars and aftermarket automotive audio where high output must come without a heatsink: 2x50 W into 4 ohms at 21 V, 4.5-V to 26-V supply range, over 90% efficiency with low idle loss. The feedback power-stage architecture delivers high PSRR so the power supply can be simpler and cheaper, while AM-avoidance switching frequencies (up to 1.2 MHz, master/slave sync) keep multi-amp systems clean. Selection advice: this is the 50-W member of the TPA31xxD2 family sharing one footprint — for 30-W designs the TPA3118D2 on this site drops into the same PCB, and for 15-W the TPA3130D2; the DAD suffix is the pad-up HTSSOP, DAP the pad-down. Programmable power limit and full fault reporting (overvoltage, overtemperature, DC-detect, short-circuit) suit unattended commercial installs. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TPA3118D2 is a Texas Instruments 30-W stereo (60-W mono) Class-D audio amplifier in 32-pin HTSSOP — for TVs, powered speakers and soundbars where 30 W per channel is the sweet spot: 2x30 W into 8 ohms at 24 V, 4.5-V to 26-V supply, pad-down package that uses the PCB plane as heatsink (no external heatsink). Same TPA31xxD2 family and footprint as the TPA3116D2, with AM-avoidance switching up to 1.2 MHz and full self-protection with error reporting. Selection advice: shares the PCB footprint with the 50-W TPA3116D2 and 15-W TPA3130D2 on this site — one layout covers three power tiers; the DAP suffix is the pad-down HTSSOP for heatsink-free builds, DAD the pad-up. For battery systems needing lower idle draw, the TPA3128D2 is TI next generation. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620BRZ-R7 is an Analog Devices instrumentation amplifier in 8-lead SOIC_N, 7-inch tape and reel — gain set from 1 to 10,000 with a single external resistor, ±2.3 V to ±18 V dual supply (4.6 V to 36 V single), 15 µV maximum input offset (B grade), 1 MHz bandwidth, 1.3 mA maximum supply current, rated −40 °C to +85 °C. The single-resistor gain setting is the selection point: bridge sensors, thermocouples and strain gauges get a precision differential front end with one resistor instead of a matched-resistor op-amp network that drifts with temperature and layout. Selection advice: BRZ is the B grade (tighter offset than the A-grade AD620ARZ-R7), R-8 the SOIC package, R7 the 7-inch reel — the AD620BRZ-RL is the identical die on a 13-inch reel if your line prefers larger reels. DigiKey lists this code Active. Evidence: the ADI AD620 datasheet Rev. H ordering guide confirms the ordering code, B grade, 7-inch reel and −40 to +85 °C rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7192BRUZ-REEL is an Analog Devices 24-bit sigma-delta ADC with integrated PGA -- for precision measurement front ends: 2 differential or 4 pseudo-differential inputs, 4.7Hz to 4.8kHz output data rate, programmable gain from 1 to 128, 24-lead TSSOP, -40C to +105C. The on-chip low-noise gain stage lets small-amplitude sensor signals interface directly to the ADC without external amplification, and the automatic channel sequencer simplifies multi-channel acquisition firmware. Business impact: a complete analog front end in one device shrinks the signal chain BOM and board area for weigh scales, strain-gage transducers and PLC/DCS input modules -- fewer parts to qualify, fewer to source. Selection advice: the REEL suffix is the tape-and-reel packing for production -- for prototyping, the tube-packed AD7192BRUZ matches electrically; the 24-bit resolution is real only when the layout follows the datasheet grounding and decoupling guidance. Featured on the lcsc.com Lightning Deals list (2026-10-12). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7606BSTZ is an Analog Devices 8-channel, 16-bit simultaneous-sampling data acquisition system in LQFP-64 — for industrial DAQ: PLC analog inputs, power-line monitoring and vibration analysis. Eight truly simultaneous 16-bit channels is the selection point: phase-accurate multi-channel capture that multiplexed ADCs cannot deliver. Selection advice: the BSTZ suffix denotes LQFP-64 — confirm your input range and throughput against the datasheet; for fewer channels, the AD7606 family's 4/6-channel siblings cut cost. Plan the analog front end (filtering, protection) per ADI's reference circuits. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.