LM358P

LM358DGKR is a Texas Instruments LM358 dual operational amplifier — the industry-standard general-purpose op-amp, 3 to 32 V single supply (±1.5 to ±16 V dual), internally frequency-compensated, in 8-pin VSSOP, tape-and-reel packing of 2500 (DGKR), 0 to +70 °C commercial grade. Single-supply operation with the common-mode range including ground is the selection point: it runs directly from one 5 V or 3.3 V rail for transducer amplifiers, DC gain blocks and comparator circuits without a negative supply. Selection advice: the output swings to about Vcc - 1.5 V — it is not rail-to-rail, so for full-swing output choose a CMOS rail-to-rail family (TLV or OPA series) instead. This DGKR code is the small VSSOP package on reel; the same die is available in SOIC, TSSOP and PDIP for hand-soldering or legacy layouts. The 0-70 °C range marks it as commercial grade — for industrial or automotive temperature ranges choose the LM2904 family. Evidence: TI LM358 datasheet and distributor listings confirm 3-32 V supply, dual channel, VSSOP-8 and 2500-reel packing. Match the full LM358DGKR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM358PWR is a Texas Instruments LM358 dual operational amplifier in TSSOP-8 on tape and reel — single supply 3 V to 32 V (or ±1.5 V to ±16 V dual), input common-mode range includes ground, unity-gain stable, two independent op-amps on a 3 × 4.4 mm footprint. The PWR code is the selection point: the same LM358 die as the PDIP-8 LM358P, but in thin-shrink SMD on reel for pick-and-place production — order PWR for volume builds, P for prototypes and hand assembly. Selection advice: the TSSOP-8 footprint is less than a third the board area of PDIP-8, which matters in dense sensor and control boards; electrically the parts are identical, so a design proven on LM358P ports to LM358PWR with only a footprint change. Same caveats as the family: not rail-to-rail output, millivolt offsets — for precision low-voltage work choose a modern RRIO op-amp. Evidence: TI LM358 product page confirms TSSOP-8 availability, 3–32 V single supply and ground-sensing inputs. Match the full LM358PWR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM393P is a Texas Instruments dual differential voltage comparator in 8-pin PDIP, tube packaging — open-collector outputs, 1.3 µs typical response time, 2 V to 36 V single-supply (or ±1 V to ±18 V dual) operation, common-mode input range that includes ground, 0 to +70 °C (P = PDIP commercial grade). The open-collector outputs with a ground-including input range are the selection point: it runs from a single 5 V rail while sensing signals down to ground, and the outputs wire-OR together for window detectors, level shifters and zero-crossing detectors in limit monitoring, battery supervisors and fan controllers. Selection advice: the P suffix is the PDIP-8 tube version — the same die ships as LM393D/DR (SOIC) for SMD lines; and because it is a comparator rather than an op amp, do not substitute an LM358 here — dedicated comparators switch far faster under saturated conditions and tolerate the high differential input voltages that would latch an op amp. TI lists LM393P as Active. Evidence: TI LM393/LM2903 datasheet and distributor listings confirm dual channels, open-collector, 1.3 µs, 2–36 V, PDIP-8 and tube packing. Match the full LM393P code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists NE5532P as an ACTIVE dual low-noise operational amplifier for audio applications in PDIP-8, with 10 MHz gain bandwidth, 9 V/µs slew rate and 10 V to 30 V supply range. The low-noise bipolar input stage is the selection point: it became the reference audio op-amp for mixing consoles and phono stages, and remains the benchmark newer audio op-amps are compared against. Selection advice: the P suffix denotes PDIP-8 — the NE5532 also ships in SOIC-8, so match the full NE5532P code to your footprint. For the lowest distortion, compare against the FET-input OPA2134; for the classic low-noise bipolar sound, match this code exactly. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TI lists OPA2134PA as ACTIVE — a dual SoundPlus FET-input audio op amp, 8 MHz GBW, 20 V/µs slew rate, 0.00008% THD, ±2.5 V to ±18 V supply, PDIP-8 tube packaging. The SoundPlus audio pedigree is the selection point: FET inputs for high impedance plus genuinely low distortion, which is why this part is the upgrade choice where the NE5532 noise or distortion budget falls short. Selection advice: the PA suffix denotes PDIP-8 — the OPA2134 ships in SOIC and other packages, so match the full code to your footprint. For new designs, compare against current-production audio op-amps if your rails or power budget differ from classic ±15 V designs. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists TL072CP as a dual JFET-input operational amplifier in PDIP-8 — for high-input-impedance analog signal paths such as guitar preamps, piezo buffers and electrometer front ends. The JFET input stage is the selection point: picoamp-level input bias current that bipolar op-amps cannot match, which is why the TL072 dominated audio and sensor front ends for decades. Selection advice: the CP suffix denotes PDIP-8 in tube packaging — the TL072 also ships in SOIC-8, so match the full TL072CP code to your footprint and packing needs. For lower noise, compare against the NE5532; for the classic JFET-input behavior, match this code exactly. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TL072IP is a Texas Instruments TL072 dual JFET-input operational amplifier in PDIP-8, tube packaging — 3 MHz gain-bandwidth, 13 V per microsecond slew rate, JFET inputs with picoamp bias current, common-mode range includes VCC+, 1.4 mA per channel, industrial −40 °C to +85 °C grade. The IP code is the selection point: the industrial-grade die in through-hole PDIP-8 — the prototyping, teaching-lab and repair choice, socketable and hand-solderable, with the wider temperature range the commercial CP codes lack. Selection advice: pick the IP for breadboards, one-offs and field repairs; pick the IDR (SOIC-8 reel) or CPWR (TSSOP-8 reel) for production — same die, different assembly flow. The JFET input keeps bias-current errors negligible on high-impedance audio and sensor sources. Not rail-to-rail output. Evidence: TI TL072 datasheet ordering information and distributor listings confirm PDIP-8 (P), tube packaging and the I-grade −40 to +85 °C range. Match the full TL072IP code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists ADS1115IDGSR as an ACTIVE 16-bit delta-sigma ADC in VSSOP-10, with 860 SPS sampling, 4 multiplexed channels and I2C interface. The 16-bit resolution is the procurement-relevant advantage: it resolves small sensor signals that a 10- or 12-bit converter would bury in quantization noise, which is why this part is the default choice for precision data-acquisition front ends. Selection advice: the IDGSR suffix pins the VSSOP-10 package on tape and reel — the ADS1115 also ships in other packages, so match the full code to your layout. Four multiplexed inputs versus the two-channel ADS1113 and single-ended/differential options are the family decision points; confirm your channel count and interface (I2C here, not SPI) against the datasheet before substituting. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDGST is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter — four single-ended or two differential inputs, programmable gain amplifier with full-scale ranges from ±6.144 V down to ±0.256 V, programmable data rates from 8 to 860 SPS, I2C interface with four pin-selectable addresses, in 10-pin VSSOP, tube packing (DGST), -40 to +125 °C. The integrated PGA, low-drift reference and oscillator are the selection point: true precision ADC performance with no external reference or clock, ideal for battery-voltage monitoring, temperature measurement and portable instrumentation. Selection advice: 860 SPS suits slow precision signals — for kilohertz sampling choose an SAR ADC (ADS868x family) instead. The built-in comparator can drive an alert pin for threshold monitoring without MCU polling, and 16 I2C addresses (four pins × four states) let you run multiple converters on one bus. Note this exact ADS1115IDGST code is the tube variant; IDGSR is the reel version. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA ranges, 8-860 SPS, VSSOP-10 and tube packing. Match the full ADS1115IDGST code for packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDYNR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin SOT-23 package — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing (DYNR), -40 to +125 °C. The SOT-23 footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in the smallest ADS1115 package for space-constrained sensor nodes. Selection advice: same die and performance as the VSSOP (IDGST) and X2QFN (IRUGR) variants — choose this code for the SOT-23 footprint and reel packing. The 150 µA active current and single-shot power-down mode suit battery designs; for 24-bit resolution or excitation sources step up to the ADS1220. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA, I2C, SOT-23-10 and reel packing. Match the full ADS1115IDYNR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.