CYT3DLABHBQ1AESGS

1ED020I12-F2 is an Infineon EiceDRIVER single-channel high-side IGBT gate driver in PG-DSO-16, tape and reel — 1200 V voltage class, ±2 A rail-to-rail output, coreless-transformer galvanic isolation, desaturation/short-circuit protection, active Miller clamp, active shutdown, UVLO on both supplies, 170 ns turn-on / 165 ns turn-off propagation delay, industrial qualified. The DESAT plus active Miller clamp combination is the selection point: a shorted IGBT is detected and shut down in hardware before the die fails, and the clamp holds the gate off against parasitic turn-on — a plain optocoupler gate drive provides neither. Selection advice: the full orderable code is 1ED020I12F2XUMA1 where XUMA1 denotes tape and reel (1,000 per reel); the 1ED020I12-B2 is the isolated variant in the same family and the 2ED020I12-F2 the dual-channel high-side version. Infineon lists this part Active, DigiKey lists the full code as in stock, and Infineon community support names it the recommended replacement for the discontinued 1ED020I12-FA. Evidence: the Infineon official datasheet Rev. 2.1 and product page confirm the ordering code, 1200 V class, ±2 A output, DSO-16 package and Active status. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

BTS6143D is an Infineon Classic PROFET single-channel smart high-side power switch in 5-pin DPAK (PG-TO252-5) — 5.5 V to 38 V operation, 10 A nominal load current, 70 A minimum short-circuit current limitation, current-sense diagnostic output, automotive qualified, rated −40 °C to +150 °C. The 70 A short-circuit current limit plus diagnosis is the selection point: a plain MOSFET passes fault current until something burns, while this device limits the short and reports it through the sense pin, so a stalled motor or pinched harness becomes a diagnosable event instead of a field failure. Selection advice: the full orderable code is BTS6143DAUMA1 where AUMA1 denotes tape and reel (2,500 per reel) — order the bare base name only if your system adds the packing suffix. In the same Classic PROFET 12 V family, the BTS6142D is the newer-generation option and the BTS6133D the 70 A-limited sibling; compare current limit and Rds(on) before substituting. Infineon lists this part Active and preferred with planned availability through 2039, and DigiKey lists the full code BTS6143DAUMA1 as Active and available for ordering. Evidence: the Infineon product page and Classic PROFET 12 V selection table confirm the ordering code, current limit, DPAK package and 2039 availability. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CY8C22545-24AXIT is an Infineon (Cypress) PSoC 1 8-bit programmable system-on-chip in 44-pin TQFP, tape and reel — 24 MHz M8C core, 16 KB flash, 1 KB RAM, 38 I/Os, three 10-bit ADCs and the original PSoC programmable analog and digital blocks. The programmable blocks are the selection point: comparators, filters, PWM and communication peripherals are configured in silicon instead of added as external parts, which is why this family still ships in legacy industrial, metering and consumer designs. Selection advice: this is PSoC 1 (8-bit M8C) — not PSoC 4/5LP (32-bit Arm); firmware and PSoC Creator projects do not transfer between generations. The AXIT code means 44-pin TQFP, industrial −40 °C to +85 °C, tape and reel; the tube version is CY8C22545-24AXI. For new designs needing CapSense or BLE, move to PSoC 4. Evidence: the Infineon CY8C22xxx datasheet ordering table and DigiKey listings confirm 16 KB/1 KB, 44-TQFP, −40 to +85 °C and Active status. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CY8C4125LQI-483 is an Infineon (Cypress) PSOC 4100 microcontroller in the PSOC 4 family. It combines an Arm Cortex-M0 core with 32 KB Flash, 4 KB SRAM and 34 GPIOs in a 40-pin QFN package. The device includes CapSense and LCD direct-drive functionality. Confirm the complete ordering code, pin assignment, supply requirements and package dimensions against your board design. For project development, this legacy device uses PSOC Creator rather than the ModusToolbox development environment; confirm device support in the tool version used for your project. Include the full part number, quantity, packing format and any date-code or inspection requirements in your RFQ. Availability and delivery terms are confirmed with the quotation.

IR2104SPBF is an Infineon Technologies 600 V half-bridge gate driver with shutdown in SOIC-8 — for half-bridge power stages: motor drives, inverters and electronic ballasts. Driving high-side (bootstrap) and low-side MOSFETs/IGBTs from logic with dead-time control is the selection point: shoot-through protection built in. Lifecycle note: Infineon lists the IR2104S as Not For New Designs — for new products, migrate to a current-production half-bridge driver; for repairs and legacy builds, we source remaining stock. Size the bootstrap capacitor per the datasheet. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

IR2110SPBF is an Infineon Technologies 500 V half-bridge gate driver with shutdown in SOIC-16 — for half-bridge and full-bridge power stages: motor drives, inverters and Class-D amplifiers. Driving both high-side (bootstrap) and low-side MOSFETs/IGBTs from logic is the selection point: complete bridge drive in one chip. Lifecycle note: Infineon lists the IR2110S as Not For New Design — for new products, migrate to a current-production half-bridge driver; for repairs and legacy builds, we source remaining stock. Size the bootstrap capacitor per the datasheet and mind dead-time in firmware. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

IR2110STRPBF is an Infineon Technologies 500 V high and low side gate driver with shutdown in SOIC-16, tape and reel — for half-bridge and full-bridge power stages: motor drives, inverters and Class-D amplifiers. Driving both high-side (bootstrap) and low-side MOSFETs/IGBTs from logic is the selection point: complete bridge drive in one chip. Selection advice: the STRPBF suffix denotes SOIC-16 in tape and reel for production — 500 V rating suits offline and industrial buses; for higher voltage or faster switching, newer gate-driver families are the step up. Size the bootstrap capacitor per the datasheet and mind dead-time in firmware. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

IR2113SPBF is an Infineon Technologies 600 V high/low-side gate driver with shutdown in SOIC-16, tube — for half-bridge and full-bridge power stages: motor drives and inverters. Driving both high-side (bootstrap) and low-side MOSFETs/IGBTs from logic is the selection point: complete bridge drive in one chip. Lifecycle note: Infineon lists the IR2113S tube variant as Not For New Design — for new products, migrate to a current-production half-bridge driver; for repairs and legacy builds, we source remaining stock. Size the bootstrap capacitor per the datasheet. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

IR2113STRPBF is an Infineon Technologies 600 V high/low-side gate driver with shutdown in SOIC-16, tape and reel — for half-bridge and full-bridge power stages: motor drives and inverters. Driving both high-side (bootstrap) and low-side MOSFETs/IGBTs from logic is the selection point: complete bridge drive in one chip. Selection advice: the STRPBF suffix denotes SOIC-16 in tape and reel for production — the 600 V rating suits offline and industrial buses; size the bootstrap capacitor per the datasheet and mind dead-time in firmware. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

IR44252LTRPBF is an Infineon low-side gate driver in SOT-23-5, tape and reel — for small MOSFETs in space-constrained designs. Lifecycle note: Infineon lists the IR44252L as discontinued (last delivery 2021-03-15) and suggests the IRS44273L as the replacement — for new designs, specify the IRS44273L; for repairs and legacy builds, we source remaining stock. 5 V to 18 V supply, 300 mA source / 550 mA sink. Parameters verified against the Infineon official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.