AMC3336QDWERQ1

AMC1350DWVR is a Texas Instruments isolated amplifier in 8-pin SOIC — for precision voltage sensing across isolation barriers: reinforced isolation with ±5V input range, optimized for AC voltage measurement in motor drives, solar inverters and power supplies where the high-voltage side must be galvanically separated from the control side. The DWVR code is the SOIC-8 reel variant with 1000-unit reel. Selection advice: the AMC1350 targets AC voltage sensing (±5V input) — for DC shunt-based current sensing the AMC1301 family is the companion choice; for designs needing an integrated DC/DC converter to power the high side, the AMC3330 eliminates the external isolated supply. Against non-isolated precision amps on this site, the isolation barrier is the differentiator — do not substitute a non-isolated amp where safety isolation is required. Heat evidence: listed in Octopart Linear ICs Popular Parts (octopart.com, verified 2026-10-09); TI E2E forum shows active customer evaluation for high-voltage measurement. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620ARZ is a low-power instrumentation amplifier from Analog Devices in an 8-pin SOIC package, with gain set by a single external resistor — for bridge sensors, strain gauges and other small differential signals. Its advantage is the classic three-op-amp instrumentation topology in one package: high common-mode rejection with minimal external circuitry, which shortens precision front-end design. Selection advice: the ARZ suffix denotes the standard grade in SOIC-8 on tape and reel — the AD620 also ships in DIP and higher grades, so match the full code to your footprint and accuracy requirements. Gain is set by one resistor value, so confirm your gain calculation against the datasheet formula during design. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620BRZ-R7 is an Analog Devices instrumentation amplifier in 8-lead SOIC_N, 7-inch tape and reel — gain set from 1 to 10,000 with a single external resistor, ±2.3 V to ±18 V dual supply (4.6 V to 36 V single), 15 µV maximum input offset (B grade), 1 MHz bandwidth, 1.3 mA maximum supply current, rated −40 °C to +85 °C. The single-resistor gain setting is the selection point: bridge sensors, thermocouples and strain gauges get a precision differential front end with one resistor instead of a matched-resistor op-amp network that drifts with temperature and layout. Selection advice: BRZ is the B grade (tighter offset than the A-grade AD620ARZ-R7), R-8 the SOIC package, R7 the 7-inch reel — the AD620BRZ-RL is the identical die on a 13-inch reel if your line prefers larger reels. DigiKey lists this code Active. Evidence: the ADI AD620 datasheet Rev. H ordering guide confirms the ordering code, B grade, 7-inch reel and −40 to +85 °C rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD623ARZ-R7 is an Analog Devices single-supply instrumentation amplifier, rail-to-rail output, gain 1 to 1000 set by one external resistor, 800 kHz bandwidth at G=1, in SOIC-8 — the sensor front-end amplifier for bridges, thermocouples and low-level transducer signals. The single-resistor gain programming is the selection point: no matched resistor networks to source, with 0.10% gain accuracy at G=1, 200 µV max offset and 550 µA max supply current for battery-powered instruments. Selection advice: it runs on 3 to 12 V single supply or ±2.5 to ±6 V dual supply — but note the input range extends only 150 mV below ground on a single rail, so ground-referenced bipolar sensor signals still need the dual-supply configuration. The R7 suffix is the 7-inch reel (1000 pcs) packing of the SOIC-8. For higher precision or lower noise, compare the AD620/AD8221 family rather than assuming drop-in equivalence. Parameters verified against the ADI AD623 datasheet and Mouser/LCSC listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8422BRZ is an Analog Devices rail-to-rail instrumentation amplifier in SOIC-8 — for bridge sensors, strain gauges and low-level differential signals where a discrete op-amp network drifts with temperature and layout. Gain is set by a single external resistor from 1 to 1000, with 25µV maximum input offset, 2.2MHz bandwidth and 150dB CMRR at high gain — precision front-end performance with minimal external circuitry. Selection advice: the BRZ code is the B grade (tighter offset than the A grade) in SOIC-8 tube packing — for reel packing specify the BRZ-R7; the MSOP-8 BRMZ suits tighter layouts. At 300µA supply current it fits battery-powered instruments, but confirm the 4.6V-to-36V supply span against your rails — for single 3.3V-only systems check the input range limits. For higher bandwidth or lower noise, compare the AD8421/AD8429 family rather than assuming interchangeability. Parameters verified against Analog Devices documentation and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists ADS1115IDGSR as an ACTIVE 16-bit delta-sigma ADC in VSSOP-10, with 860 SPS sampling, 4 multiplexed channels and I2C interface. The 16-bit resolution is the procurement-relevant advantage: it resolves small sensor signals that a 10- or 12-bit converter would bury in quantization noise, which is why this part is the default choice for precision data-acquisition front ends. Selection advice: the IDGSR suffix pins the VSSOP-10 package on tape and reel — the ADS1115 also ships in other packages, so match the full code to your layout. Four multiplexed inputs versus the two-channel ADS1113 and single-ended/differential options are the family decision points; confirm your channel count and interface (I2C here, not SPI) against the datasheet before substituting. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDGST is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter — four single-ended or two differential inputs, programmable gain amplifier with full-scale ranges from ±6.144 V down to ±0.256 V, programmable data rates from 8 to 860 SPS, I2C interface with four pin-selectable addresses, in 10-pin VSSOP, tube packing (DGST), -40 to +125 °C. The integrated PGA, low-drift reference and oscillator are the selection point: true precision ADC performance with no external reference or clock, ideal for battery-voltage monitoring, temperature measurement and portable instrumentation. Selection advice: 860 SPS suits slow precision signals — for kilohertz sampling choose an SAR ADC (ADS868x family) instead. The built-in comparator can drive an alert pin for threshold monitoring without MCU polling, and 16 I2C addresses (four pins × four states) let you run multiple converters on one bus. Note this exact ADS1115IDGST code is the tube variant; IDGSR is the reel version. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA ranges, 8-860 SPS, VSSOP-10 and tube packing. Match the full ADS1115IDGST code for packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDYNR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin SOT-23 package — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing (DYNR), -40 to +125 °C. The SOT-23 footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in the smallest ADS1115 package for space-constrained sensor nodes. Selection advice: same die and performance as the VSSOP (IDGST) and X2QFN (IRUGR) variants — choose this code for the SOT-23 footprint and reel packing. The 150 µA active current and single-shot power-down mode suit battery designs; for 24-bit resolution or excitation sources step up to the ADS1220. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA, I2C, SOT-23-10 and reel packing. Match the full ADS1115IDYNR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin X2QFN package (2 × 1.5 × 0.4 mm) — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing of 3000 (IRUGR; IRUGT is the small reel), -40 to +125 °C. The 2 × 1.5 mm footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in one of the smallest ADC packages available, for wearables and dense sensor boards. Selection advice: same die and performance as the VSSOP (IDGSR) and SOT-23 (IDYNR) variants — choose this code for the X2QFN footprint and 3000-reel packing. Leadless QFN needs reflow assembly and good layout practice; for hand-soldering prototypes choose the VSSOP variant. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D), TI pack addendum and DigiKey listings confirm 16-bit, PGA, I2C, X2QFN-10 and 3000-reel packing. Match the full ADS1115IRUGR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGT is a Texas Instruments 16-bit delta-sigma ADC in 10-pin X2QFN (2.0 × 1.5 × 0.4 mm), 250-piece small reel — I2C interface, four single-ended or two differential inputs, programmable gain amplifier (±256 mV to ±6.144 V), internal low-drift reference and oscillator, programmable comparator, 8 to 860 SPS, 2.0–5.5 V, 150 µA, −40 °C to +125 °C. The integration is the selection point: PGA, MUX, reference, oscillator and comparator on one 2×1.5 mm die means a complete sensor front end with no external analog support chips. Selection advice: the RUG package code is the X2QFN — ADS1115IDGST is the same die in VSSOP-10 on 250-piece small reel — the easier-to-assemble alternative for designs that do not need the 2×1.5 mm X2QFN footprint, not interchangeable on the same footprint. Against the 12-bit ADS1015: pick the ADS1115 for resolution (weighing, precision sensing), the ADS1015 for speed (3300 SPS). The ADDR pin gives four I2C addresses, so up to four devices share one bus. Evidence: TI ADS1115 datasheet (ordering addendum) and distributor listings confirm X2QFN-10, 250-reel, 16-bit, I2C and −40 to +125 °C. Match the full ADS1115IRUGT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.