ADUM4160BRWZ-RL

ADM3054BRWZ is an Analog Devices isolated high-speed CAN transceiver — 16-lead wide-body SOIC, 5 kV rms signal isolation, bus protection, up to 1 Mbps, −40 to +125 °C. The integrated 5 kV isolation is the selection point: isolated CAN in one chip — no separate isolator plus transceiver, which halves the BOM for isolated CAN nodes. Selection advice: ADI lists the ADM3054BRWZ as Production. The BRWZ code pins the 16-lead wide-body SOIC — match it to your footprint. Verify the isolation working voltage against your safety standard, and note the isolated side needs its own supply — budget the isolated DC-DC in the BOM. Evidence: ADI data confirms Production, 16-lead wide-body SOIC, 5 kV rms isolation, 1 Mbps. Match the full ADM3054BRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM4223ARWZ is an Analog Devices dual-channel isolated half-bridge driver — 16-lead wide-body SOIC, independent high-side and low-side outputs, 4 A peak output, 5 kV rms isolation, grade A UVLO (4.1 V typ), 5 ns channel matching. The 5 ns channel matching is the selection point: tight high/low-side timing for clean half-bridge switching — deadtime accuracy that discrete drivers cannot match. Selection advice: ADI lists the ADUM4223ARWZ as Production. The ARWZ code pins the 16-lead wide-body variant — match it to your footprint; the grade A UVLO suits 5 V logic drive. Verify the 4 A peak against your switch gate charge at the switching frequency, and the isolation working voltage against your safety standard. Evidence: ADI data confirms Production, 16-lead wide-body SOIC, 4 A peak, 5 kV rms isolation, 5 ns matching. Match the full ADUM4223ARWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM4223BRWZ is an Analog Devices iCoupler isolated dual gate driver in wide-body 16-SOIC — 4 A peak output, 5000 VRMS reinforced isolation, two independent isolated channels for high-side and low-side driving, 3.0 V to 5.5 V input supply, 4.5 V to 18 V output drive supply, 49 ns maximum propagation delay with 5 ns channel matching, >25 kV/µs common-mode transient immunity, -40 to +125 °C, tube packing (Z). The B grade is the selection point: 7.0 V UVLO threshold on the output supplies — designed for systems whose gate-drive rail is regulated below 12 V. Selection advice: the A/B/C grades differ only in the output-supply UVLO threshold (A 4.1 V, B 7.0 V, C 11.0 V) — pick the grade matching your actual gate-drive voltage. The WBRWZ/WCRWZ codes are the AEC-Q100 automotive variants. Evidence: ADI ADuM3223/4223 datasheet (Rev. I) and distributor listings confirm 4 A, 5000 VRMS, wide-body 16-SOIC and tube packing. Match the full ADUM4223BRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM4223CRWZ is an Analog Devices iCoupler isolated dual gate driver in wide-body 16-SOIC — 4 A peak output, 5000 VRMS reinforced isolation, two independent isolated channels for high-side and low-side driving, 3.0 V to 5.5 V input supply, 4.5 V to 18 V output drive supply, 49 ns maximum propagation delay with 5 ns channel matching, >25 kV/µs common-mode transient immunity, -40 to +125 °C, tube packing (Z). The C grade is the selection point: 11.0 V UVLO threshold on the output supplies — designed for 12 V gate-drive rails where the driver stays off until the rail is solid. Selection advice: the A/B/C grades differ only in the output-supply UVLO threshold (A 4.1 V, B 7.0 V, C 11.0 V) — pick the grade matching your actual gate-drive voltage. The WBRWZ/WCRWZ codes are the AEC-Q100 automotive variants. Evidence: ADI ADuM3223/4223 datasheet (Rev. I) and distributor listings confirm 4 A, 5000 VRMS, wide-body 16-SOIC and tube packing. Match the full ADUM4223CRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS3231M+ is an Analog Devices (Maxim) I2C real-time clock in wide SOIC-16 — for timekeeping that stays accurate without calibration: meters, data loggers and access systems. The ±5 ppm MEMS-based accuracy is the selection point: seconds-per-month accuracy with no external crystal. Selection advice: the M+ denotes the MEMS variant in wide SOIC-16 — pick it over the DS1307 when accuracy matters and board space allows; the SN# (TCXO) variant offers tighter ±2 ppm. Battery backup keeps time through power loss. ADI lists this part as PRODUCTION. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS3231SN# is an Analog Devices (Maxim) extremely accurate I2C real-time clock with integrated TCXO and crystal in 16-pin SO — for timekeeping that stays accurate without calibration: meters, data loggers and access systems. The ±2 ppm integrated TCXO is the selection point: seconds-per-month accuracy with no external crystal or trimming. Selection advice: the SN# suffix denotes 16-pin SO — pick the DS3231 over the cheaper DS1307 when accuracy matters; the DS1307 needs an external crystal and drifts far more. Battery backup keeps time through power loss. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MAX232ESE+ is an Analog Devices (Maxim) dual RS-232 driver/receiver with on-chip charge pump in 16-pin SOIC — for legacy serial ports: industrial consoles, POS terminals and instrumentation. The integrated charge pump is the selection point: true RS-232 levels from a single 5 V supply, no ±12 V rails. Selection advice: the ESE+ denotes 16-pin SOIC — for 3.3 V systems, the MAX3232 is the pin-compatible low-voltage sibling; for new designs, consider USB instead of RS-232. Four external charge-pump capacitors required per the datasheet. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620BRZ-R7 is an Analog Devices instrumentation amplifier in 8-lead SOIC_N, 7-inch tape and reel — gain set from 1 to 10,000 with a single external resistor, ±2.3 V to ±18 V dual supply (4.6 V to 36 V single), 15 µV maximum input offset (B grade), 1 MHz bandwidth, 1.3 mA maximum supply current, rated −40 °C to +85 °C. The single-resistor gain setting is the selection point: bridge sensors, thermocouples and strain gauges get a precision differential front end with one resistor instead of a matched-resistor op-amp network that drifts with temperature and layout. Selection advice: BRZ is the B grade (tighter offset than the A-grade AD620ARZ-R7), R-8 the SOIC package, R7 the 7-inch reel — the AD620BRZ-RL is the identical die on a 13-inch reel if your line prefers larger reels. DigiKey lists this code Active. Evidence: the ADI AD620 datasheet Rev. H ordering guide confirms the ordering code, B grade, 7-inch reel and −40 to +85 °C rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7192BRUZ-REEL is an Analog Devices 24-bit sigma-delta ADC with integrated PGA -- for precision measurement front ends: 2 differential or 4 pseudo-differential inputs, 4.7Hz to 4.8kHz output data rate, programmable gain from 1 to 128, 24-lead TSSOP, -40C to +105C. The on-chip low-noise gain stage lets small-amplitude sensor signals interface directly to the ADC without external amplification, and the automatic channel sequencer simplifies multi-channel acquisition firmware. Business impact: a complete analog front end in one device shrinks the signal chain BOM and board area for weigh scales, strain-gage transducers and PLC/DCS input modules -- fewer parts to qualify, fewer to source. Selection advice: the REEL suffix is the tape-and-reel packing for production -- for prototyping, the tube-packed AD7192BRUZ matches electrically; the 24-bit resolution is real only when the layout follows the datasheet grounding and decoupling guidance. Featured on the lcsc.com Lightning Deals list (2026-10-12). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7606BSTZ is an Analog Devices 8-channel, 16-bit simultaneous-sampling data acquisition system in LQFP-64 — for industrial DAQ: PLC analog inputs, power-line monitoring and vibration analysis. Eight truly simultaneous 16-bit channels is the selection point: phase-accurate multi-channel capture that multiplexed ADCs cannot deliver. Selection advice: the BSTZ suffix denotes LQFP-64 — confirm your input range and throughput against the datasheet; for fewer channels, the AD7606 family's 4/6-channel siblings cut cost. Plan the analog front end (filtering, protection) per ADI's reference circuits. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.