DRV8886PWPR

DRV8424EPWPR is a Texas Instruments 35 V, 2.5 A stepper / 4 A peak brushed dual H-bridge driver — 28-pin HTSSOP with integrated current sensing (no external shunt resistor), 4.5–33 V supply, −40 to +125 °C. The integrated current sensing is the selection point: no external shunt resistors — smaller BOM and no sense-resistor layout for 2.5 A stepper drive. Selection advice: TI lists the DRV8424EPWPR as In Production. The EPWPR suffix pins the HTSSOP-28 package on tape and reel — match it to your footprint; the exposed thermal pad needs soldered copper. The −40 to +125 °C grade suits industrial designs. For basic 1.9 A stepping the DRV8811 is cheaper; choose the DRV8424 where the shuntless sensing pays off. Evidence: TI data confirms In Production, 35 V, 2.5 A, integrated current sense, HTSSOP-28. Match the full DRV8424EPWPR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DRV8811PWPR is a Texas Instruments 38 V, 1.9 A bipolar stepper motor driver — 28-pin HTSSOP, 8–38 V supply, indexer with built-in current-decay modes, −40 to +85 °C. The built-in indexer is the selection point: step and direction in, microstepped coil currents out — no MCU PWM sequencing needed. Selection advice: TI lists the DRV8811PWPR as In Production. The PWPR suffix pins the HTSSOP-28 package on tape and reel — match it to your footprint; the exposed thermal pad needs soldered copper for the 1.9 A rating. For higher current steppers use the DRV8841 (2.5 A) instead. Evidence: TI data confirms In Production, 38 V, 1.9 A stepper driver, HTSSOP-28, indexer. Match the full DRV8811PWPR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DRV8825 is a Texas Instruments 45-V, 2.5-A bipolar stepper motor driver with integrated microstepping indexer — for printers, 3D printers, CNC machines, robotics and factory automation: 8.2-V to 45-V supply, up to 1/32 microstepping, simple STEP/DIR interface, and multiple decay modes (mixed, slow, fast) for smooth quiet motion. The selection point is the on-chip indexer: no external microstepping lookup tables needed, and the 400-mΩ RDS(ON) keeps conduction losses low at 1.5-A RMS without a heatsink. Selection advice: the DRV8825 is the higher-current drop-in upgrade path from the A4988 carrier footprint — for new designs needing integrated current sensing and 1/256 microstepping, the DRV8424 family is the newer alternative; for lower current the pin-compatible DRV8824 covers 1.6 A. TI lists factory automation and robotics as target applications. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DRV8825PWPR is a Texas Instruments microstepping bipolar stepper motor driver in HTSSOP-28 PowerPAD, tape and reel — for 3D printers, scanners and office automation driving one bipolar stepper with smooth, quiet motion. 8.2 V to 45 V supply with up to 2.5 A per coil and 1/32 microstepping is the selection point: high-voltage headroom plus fine microstepping from a simple STEP/DIR interface. Selection advice: the PWP suffix denotes the thermally enhanced HTSSOP-28 — solder the exposed pad to copper, because 2.5 A is only reachable with proper heatsinking; R denotes tape and reel. Against the Allegro A4988 on this site (35 V, 2 A, 1/16 step): pick the DRV8825 for higher voltage, higher current and finer microstepping; pick the A4988 for lower cost at modest power. Built-in overcurrent, thermal shutdown and undervoltage lockout plus the nFAULT pin simplify fault handling. TI lists this part as Active. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DRV8841PWPR is a Texas Instruments 45 V, 2.5 A bipolar stepper or dual H-bridge motor driver — 28-pin HTSSOP with current regulation and PWM control, 8.2–45 V supply, −40 to +85 °C. The dual-mode operation is the selection point: one stepper or two brushed DC motors from the same chip — flexible motor drive for multi-motor products. Selection advice: TI lists the DRV8841PWPR as In Production. The PWPR suffix pins the HTSSOP-28 package on tape and reel — match it to your footprint; the exposed thermal pad needs soldered copper for the 2.5 A rating. For 5 A single bridges use the DRV8842 instead. Evidence: TI data confirms In Production, 45 V, 2.5 A, stepper/dual-H-bridge, HTSSOP-28. Match the full DRV8841PWPR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

A4988SETTR-T is an Allegro MicroSystems DMOS microstepping stepper motor driver in QFN-28, tape and reel — for 3D printers, CNC machines and consumer motion control where a proven low-cost stepper driver matters. Built-in translator with full-step down to 1/16 microstepping, 35 V and ±2 A drive is the selection point: one STEP pulse equals one microstep, no phase tables to program. Selection advice: the SETTR-T suffix denotes the QFN-28 package in tape and reel; the SET temperature grade covers −20 °C to +85 °C. Against the TI DRV8825 on this site (45 V, 2.5 A, 1/32 step): the A4988 costs less and is the 3D-printing classic, but tops out at 1/16 microstepping and lower voltage — pick it when the motor fits within 35 V and 2 A. Synchronous rectification keeps dissipation low; thermal shutdown and short-circuit protections are built in. On 3D-printer StepStick-style modules the A4988 and DRV8825 footprints are largely interchangeable — but check driver orientation, microstepping jumpers and current setting before swapping, as the two parts differ. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

F: 3.0-A standalone switch-mode buck charger with NVDC power path for single-cell Li-Ion/Li-polymer, 3.9-13.5-V input, 19.5-mohm BATFET, 9.5-uA battery leakage, WQFN-24. A: Full FET integration and hardware-configurable JEITA profile deliver fast charging without host firmware management. B: Shorter firmware development and faster time-to-market for portable devices. E: Ranked on hqbuy.com real-time hot list (2026-10-14). Selection advice: pick BQ25616 over the I2C siblings BQ25618/BQ25619 when the host MCU should not own charging registers; note this RTWR orderable is the WQFN-24 tape-and-reel option. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

BQ25790 is Texas Instruments’ 5-A buck-boost battery charger for 1-to-4-cell Li-ion/Li-polymer packs in 2.9x3.3mm WCSP-56 — for USB-C PD charging where input voltage swings both above and below the battery voltage: the integrated buck-boost stage (all four switching FETs plus battery FET on-chip) automatically transitions between buck, boost and buck-boost without host intervention. 97% charging efficiency at 30 W, 3.6-to-24 V input range, NVDC power-path management that keeps the system alive even with a dead or removed battery, dual-input selector (USB, barrel, wireless, solar), D+/D- handshake for legacy fast-charge adapters, and I2C host control with an integrated ADC for telemetry. USB-C/PD compatible, -40 to +85°C. Selection advice: the WCSP package is the smallest footprint option — for easier assembly specify the QFN sibling BQ25792; for solar-input designs the BQ25798 variant adds MPPT. State cell count and input source mix in the RFQ so the offered lot is matched to the right charge profile. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

BQ4050RSMR is a Texas Instruments battery fuel gauge — for 1-series Li-ion and Li-polymer packs: Impedance Track gauging algorithm for accurate state-of-charge reporting, integrated protection-friendly architecture, VQFN-12 package. The Impedance Track algorithm learns the cell characteristics over cycles, so reported capacity stays accurate as the battery ages — unlike simple coulomb counters that drift; accurate gauging prevents both unexpected shutdowns and over-conservative capacity margins. Business impact: reliable fuel gauging is a safety and user-experience feature — medical, industrial and consumer devices all depend on trustworthy remaining-capacity readings. Selection advice: the RSMR code denotes VQFN-12 on tape and reel — the BQ4050 targets single-cell packs — for multi-cell designs look at the BQ40 family stackable gauges; cell characterization data improves initial accuracy. Ranked #15 on the hqbuy.com real-time hot list (2026-10-05). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CSD95410RRB is a Texas Instruments 90 A peak NexFET smart power stage — for multiphase buck converters powering AI accelerators, FPGAs and datacenter ASICs: driver plus power MOSFETs in a 5x6 mm 41-pin VQFN-CLIP package, -40°C to +125°C. Integrated temperature-compensated bidirectional current sense and analog temperature output feed the controller's telemetry loop, while 1.75 MHz switching and ultra-low-inductance packaging push power density. This is the ACTIVE successor to the NRND CSD95490 — same footprint class, higher current rating. Selection advice: pair with TI multiphase controllers (TPS53681/TPS53688 on this site) per TI reference designs; the industry-common 5x6 mm footprint allows second-sourcing across vendors, but verify current-sense calibration against your controller. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.