CD4052BE

CD4017BE is a CMOS decade counter and divider from Texas Instruments in a 16-pin PDIP package — for LED chasers, sequencers, frequency dividers and event counters. Its advantage is the decoded 10-output structure: one clock in, ten sequential outputs out, with no microcontroller or firmware needed for simple sequencing tasks. Selection advice: the BE suffix denotes the PDIP-16 through-hole package — the CD4017B also ships in SOIC and TSSOP, so match the full CD4017BE code to your assembly process. CMOS logic runs on a wide supply range but verify your actual VDD against the datasheet, and note that outputs drive limited current — buffer them for relays or bright LEDs. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CD4051BE is a Texas Instruments 20 V 8:1 single-channel analog multiplexer/demultiplexer in 16-pin PDIP — for routing analog signals: sensor selection, audio switching and test fixtures. The 20 V analog range is the selection point: handling signals far beyond the logic supply that modern low-voltage muxes cannot. Selection advice: the BE suffix denotes PDIP-16 — the breadboard-friendly variant; for SMT, the SOIC/TSSOP variants are the pick. Mind the higher on-resistance versus modern muxes when driving low-impedance loads. TI lists this order code as Active. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CD4511BE is a Texas Instruments CMOS BCD-to-7-segment latch decoder driver for common-cathode LED displays in 16-pin PDIP — for driving 7-segment displays from BCD: counters, panel meters and clocks. The integrated latch plus segment drivers is the selection point: BCD in, display out, with no MCU multiplexing. Selection advice: the BE suffix denotes PDIP-16 — the breadboard-friendly variant; note it drives common-cathode displays only (the CD4510/CD4543 cover other configurations). TI lists this order code as Active (In Stock). Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN74HC595N is a Texas Instruments 8-bit serial-in parallel-out shift register with 3-state outputs in PDIP-16, tube — for expanding MCU outputs on breadboards and prototypes: LED matrices, relay banks and 7-segment displays. Three pins driving unlimited cascaded outputs is the selection point: GPIO expansion at cents per pin. Selection advice: the N suffix denotes PDIP-16 in tube — the hand-solder-friendly variant for prototypes and education; for SMT production, the D (SOIC) or PW (TSSOP) variants are the pick. 24 MHz clock covers most display multiplexing. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ULN2003AN is a Texas Instruments seven-channel Darlington transistor array in PDIP-16, tube — for driving relays, solenoids and low-side loads from logic outputs. Seven integrated Darlington pairs with freewheeling diodes is the selection point: one chip replaces seven transistor-plus-diode circuits. Selection advice: the AN suffix denotes PDIP-16 in tube — the breadboard- and hand-solder-friendly variant for prototypes and repairs; for SMT production, the SOP ULN2003ANSR or SOT-23 DYYR variants are the pick. Each channel sinks up to 500 mA. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS7846 is a Texas Instruments 4-wire resistive touch screen controller in 16-pin TSSOP — the industry-standard part behind two decades of PDAs, point-of-sale terminals and portable instruments: 2.2 V to 5.25 V operation, internal 2.5 V reference, direct battery measurement from 0 V to 6 V, on-chip temperature and touch-pressure measurement, SPI/QSPI 3-wire interface, auto power-down, under 0.75 mW typical at 2.7 V, 125 kHz throughput, -40 to +85 °C. The pin-compatible upgrade path is the selection point: it drops into ADS7843 sockets with only software changes, adding battery and temperature measurement the older part lacks — which is why it remains the default choice for resistive-touch retrofits and long-life industrial designs. Selection advice: for new designs needing 1.5 V digital I/O, the TSC2046 on this site is the pin-compatible successor; the TSSOP-16 is the standard package, with QFN-16 and VFBGA-48 for space-constrained boards. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AM2434BSDFHIALVR is a Texas Instruments Sitara AM243x high-performance MCU: up to four 800 MHz Arm Cortex-R5F cores, a 400 MHz Cortex-M4F, and dual gigabit PRU-ICSSG industrial-communication subsystems in a 441-ball FCBGA (17.2 x 17.2 mm). It is TI's consolidation play for factory automation — the R5F cluster delivers deterministic servo-loop control while the PRU-ICSSG runs full protocol stacks for EtherCAT target, PROFINET device and EtherNet/IP adapter on the same silicon, replacing architectures that needed an MCU plus an external industrial-Ethernet ASIC or FPGA. Heat evidence: the AM243x is TI's mainstream platform for servo drives and remote I/O modules, and its datasheet remains under active revision (Rev. J, 2026), signaling continued TI investment in the family. Selection advice: the full orderable encodes silicon revision, feature configuration, temperature grade and the ALV 441-ball FCBGA package on tape and reel — match it character-for-character; the ALX 293-ball FCCSP is a smaller, footprint-incompatible alternative, and R5F count plus PRU features vary across AM2431/32/34. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AM6232ATGGHIALWR is a Texas Instruments Sitara AM62x processor: dual 1.4 GHz Arm Cortex-A53 plus a Cortex-M4F in a 425-ball FCCSP (13 x 13 mm). The value proposition is Linux-class compute at microcontroller-class power — the A53 pair runs full Yocto/Debian HMI stacks while the M4F handles real-time I/O, so one device replaces an applications processor plus a companion MCU in industrial panels and gateways, and deep-sleep states in the milliwatt class simplify thermal and power design. TI's long-lifecycle industrial positioning protects multi-year programs from forced redesigns. Heat evidence: the AM62x family has been one of TI's most heavily promoted industrial platforms since its 2022 launch, with broad trade-press coverage and multiple third-party system-on-module vendors building AM62x-based products for HMI and edge AI. Selection advice: the ALW FCCSP-425 is the compact package variant — the AM625/AM623/AM620-Q1 family shares one TI product folder, so confirm the exact orderable against the datasheet because family members differ in feature set; the G temperature code and W carrier suffix must match your assembly flow. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AWR2944ABGALTRQ1 is a Texas Instruments 76–81 GHz single-chip FMCW radar sensor in 266-ball FCCSP, tape and reel — 4 transmit and 4 receive channels, Arm Cortex-R5F plus C66x DSP plus radar hardware accelerator for signal processing, 4 MB on-chip memory, CAN-FD, Ethernet, hardware security module, AEC-Q100 qualified and ASIL-B capable. The fourth transmitter is the selection point: 33% higher angular resolution than previous-generation corner radars, which is what enables reliable blind-spot detection, lane-change assist and cross-traffic alert under UN R79 and NCAP requirements. Selection advice: the R suffix is tape and reel, Q1 is the automotive qualification; lower-cost LC/ECO variants exist for non-safety designs, so do not pay for the ASIL-B part in a non-safety application. Automotive radar designs require RF layout discipline — follow the TI reference design, not a generic BGA flow. Evidence: the TI AWR2944 datasheet (device nomenclature and packaging addendum) confirms the 4×4 channels, 266-ball FCCSP, reel packing and automotive qualification. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CC1101RGP is a Texas Instruments sub-1 GHz RF transceiver in VQFN-20, tube packaging — for proprietary wireless sensor links in metering, alarms and remote control. The sub-1 GHz operation is the selection point: better wall penetration and range than 2.4 GHz at the same power budget. Selection advice: the RGP suffix denotes VQFN-20 in tube — for production volumes, the RGPT tape-and-reel variant feeds pick-and-place directly. This is a transceiver, not a protocol stack — plan firmware for your own packet format or a lightweight stack. Match the order code to your assembly process. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.