DP83848IVVX/NOPB

DP83TC812RRHARQ1 is a Texas Instruments AEC-Q100 Grade 1 100BASE-T1 automotive Ethernet PHY in 36-pin VQFN (6x6mm) — for zonal E/E architectures replacing CAN with Ethernet: zone controllers, ADAS sensor fusion and infotainment backbones. IEEE 802.3bw compliant, TC-10 sleep/wake under 20µA, integrated low-pass filter passing Level IV emissions, and MII/RMII/RGMII MAC interfaces with 1.8V/2.5V/3.3V I/O. Heat evidence: automotive Ethernet is the fastest-growing in-vehicle networking segment — OEMs are shifting from domain to zonal architectures, and 100BASE-T1 is the volume PHY for camera/radar links. Selection advice: the R variant includes RGMII — for SGMII-only designs the S variant costs less; the integrated LPF eliminates external magnetics filtering. AEC-Q100 Grade 1 (-40 to +125°C) with ±8kV IEC ESD on MDI pins. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DP83867ERGZR is a Texas Instruments 10/100/1000BASE-T Gigabit Ethernet PHY in 48-pin VQFN (7x7mm) — for industrial Ethernet nodes where deterministic latency and diagnostics matter: PLCs, machine vision cameras and grid automation. RGMII and SGMII MAC interfaces, IEEE 1588 start-of-frame detection for time-sensitive networking, cable diagnostics, and 8kV IEC 61000-4-2 ESD protection. Selection advice: the E variant covers -40 to +105°C — for commercial 0 to +70°C the CS code costs less, and the IR code targets -40 to +85°C industrial; for 10/100 Mbps only the DP83848 on this site is the economical choice. 457mW full-power draw suits fanless enclosures. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS160PR410NJXR is a Texas Instruments quad-channel linear redriver for PCI Express 4.0 (16 Gbps) in 40-pin WQFN (6x4mm), tape and reel — for extending PCIe reach across backplanes and cables in rack servers, HBAs, NICs and hardware accelerators. CTLE boost up to 18 dB at 8 GHz reopens eyes closed by PCB trace loss; protocol-agnostic linear datapaths preserve link-training behavior, with 70 ps typical latency and 60 fs additive jitter. Single 3.3V supply at 124 mW per channel needs no heatsink; pin-strap, SMBus or EEPROM programming covers x2/x4/x8/x16 widths. Selection advice: the NJXR suffix is the WQFN-40 industrial (-40 to +85°C) tape-and-reel orderable — for automotive programs use the DS160PR410-Q1 instead; as a linear (not retimer) redriver it adds no protocol latency, which suits latency-sensitive accelerator fabrics, but for very long reaches evaluate a retimer instead. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ISO1044BD is a Texas Instruments galvanically isolated CAN FD transceiver in SOIC-8 — for CAN buses that cross ground domains: EV battery packs, solar inverters and motor drives where noise currents must not enter the local ground. 5 Mbps CAN FD data rate, ±58V DC bus fault protection, 3000 VRMS isolation barrier, and -40 to +125°C operation. Selection advice: this is the CAN FD generation — for classic CAN isolation the ISO1050 on this site is the established choice; the SOIC-8 D package replaces optocoupler-plus-transceiver discrete solutions in a fraction of the board area. Pair with an isolated power supply for a complete isolated CAN node. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ISO1050DUBR is a Texas Instruments galvanically isolated CAN transceiver in SOP-8, tape and reel — for CAN nodes in harsh environments: motor drives, solar inverters and industrial controllers where ground noise must not reach the MCU. 2500 VRMS isolation with 1 Mbps CAN and −27 V to 40 V bus-fault protection is the selection point: isolation and the transceiver in one 8-pin package, no optocouplers. Selection advice: the DUB suffix denotes the SOP-8 package with 2500 VRMS — for 5000 VRMS, the DW-packaged ISO1050DW is the sibling. Pair it with a CAN controller such as the MCP2515 on this site — the ISO1050 is the isolated bus driver, not the protocol engine. 3 V to 5.5 V supply supports 3.3 V and 5 V logic; −55 °C to +105 °C. TI lists this part as Active through distribution. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ISO1050DWR is a Texas Instruments ISO1050 galvanically isolated CAN transceiver — meets ISO 11898-2, 5000 VRMS isolation in the wide-body 16-pin SOIC package, signaling up to 1 Mbps, tape-and-reel packing of 2000 (DWR), -55 to +105 °C. Silicon-dioxide isolation in a single chip is the selection point: it replaces optocoupler-based isolated CAN solutions with lower loop delay (150 ns typical), smaller footprint and longer working-voltage life for industrial automation, motor control and medical equipment. Selection advice: galvanic isolation is only complete with an isolated power supply on the bus side — pair it with an isolated DC/DC module. The DW package gives 5000 VRMS; the smaller DUB package is rated 2500 VRMS, so match isolation level to your safety standard. Bus-fault protection (-27 to 40 V) and dominant time-out add robustness on harsh factory floors. Evidence: TI ISO1050 datasheet (SLLS983L) and distributor listings confirm 5000 VRMS, 1 Mbps, SOIC-16 and 2000-reel packing. Match the full ISO1050DWR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN65HVD230DR is a Texas Instruments 3.3 V CAN transceiver in SOIC-8, tape and reel — for industrial automation, motor control and building systems adding CAN bus to 3.3 V MCUs. ISO 11898-compliant 1 Mbps transceiver running from a single 3.3 V supply is the selection point: no 5 V rail needed for the CAN physical layer. Selection advice: the R suffix denotes tape and reel. Low-power standby (370 µA typical) suits battery-backed nodes; ±16 kV HBM bus ESD, thermal shutdown and open-circuit fail-safe harden the bus; up to 120 nodes per bus. It is documented as a low-power 3.3 V replacement for the classic 5 V PCA82C250 footprint — for new native 5 V CAN designs, stay with a 5 V transceiver. Not automotive qualified — for AEC-Q100, ask about the Q1-qualified variant. TI lists this part as Active. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN65HVD3082EDR is a Texas Instruments SN65HVD3082E low-power half-duplex RS-485 transceiver — up to 200 kbps signaling rate, single 5 V supply, 8-pin SOIC, tape-and-reel packing of 2500 (R suffix; EP is the PDIP tube version), -40 to +85 °C. The low power and robustness are the selection point: 0.3 mA typical supply current, 1/8-unit-load input supporting up to 256 nodes on the bus, 15 kV bus-pin ESD protection and fail-safe receiver for open/idle lines. Selection advice: the 3082E is the 200 kbps variant — for 1 Mbps choose SN65HVD3085E or for 20 Mbps SN65HVD3088E, which are pin-compatible upgrades in the same family. This is half-duplex (one driver, one receiver); full-duplex RS-422/485 needs a different device. TI lists this code as Active. Evidence: TI SNx5HVD308xE datasheet (ordering information and package addendum) confirms 200 kbps, SOIC-8, 2500/reel packing and -40 to +85 °C. Match the full SN65HVD3082EDR code for data rate, package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN74LVC1T45DCKR is a Texas Instruments single-bit dual-supply bus transceiver with configurable voltage translation in a 6-pin SC70 package - for bridging mismatched logic domains on space-constrained boards: VCCA and VCCB each operate from 1.65V to 5.5V, DIR pin selects direction with a single logic level, plus-minus 24mA output drive at 3.3V, up to 420Mbps when translating 3.3V to 5V, Ioff circuitry and VCC isolation put both ports in high impedance when either supply is down, -40C to 85C. The fully configurable dual-rail design is the selection point: any standard node (1.8V, 2.5V, 3.3V, 5V) translates to any other without external direction glue, so mixed-voltage designs drop a discrete level-shifter network. Business impact: one SC70 device replaces a FET-plus-resistor discrete shifter, cutting placement cost and board area on every mixed-voltage interface. Selection advice: the DCKR code is the SC70 3000-piece tape-and-reel packing - for SOT-23 pick the DBVR code, for SOT-5X3 pick the DRLR code; verify the DIR pin is driven by VCCA-referenced logic and that both supplies stay within 1.65V to 5.5V. Ranked #4 on the lcsc.com flash-sale page (2026-10-16). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

SN74LVC1T45DRLR is a Texas Instruments single-bit dual-supply bus transceiver with configurable voltage translation - for bridging mismatched logic domains on space-constrained boards: both VCCA and VCCB operate over the full 1.65V to 5.5V range, SOT-5X3 (DRL) 6-pin package (1.60mm x 1.20mm), plus-minus 24mA output drive at 3.3V, up to 420Mbps when translating 3.3V to 5V, -40C to 85C. The fully configurable dual-rail design translates between any standard nodes (1.8V, 2.5V, 3.3V, 5V) without external direction glue, so mixed-voltage designs drop a discrete level-shifter network; Ioff circuitry and VCC isolation put both ports in high-impedance when either supply is down, preventing backflow damage during partial power-down sequencing. Business impact: one SOT-5X3 device replaces a FET-plus-resistor discrete shifter, cutting placement cost and board area on every mixed-voltage interface - the DIR pin selects direction with a single logic level. Selection advice: the DRLR suffix is the SOT-5X3 tape-and-reel packing - for SC70 consider the DCKR variant, for DSBGA the YZPR; verify the DIR pin is driven by VCCA-referenced logic and that both supplies stay within 1.65V to 5.5V. Ranked #16 on the hqew.com hot list (2026-10-11). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.