S34ML04G200TFI000

The Delkin EM64FSTWH-BA000-2 is a 64 GB industrial eMMC (G632 series, 3D Industrial NAND) with a wide temperature range of -40°C to +85°C. Delkin's official Industrial eMMC Part Numbers table lists this exact part number with Status: Active — while most other 32/64 GB devices in the series have gone EOL, this is the currently orderable version. The 64 GB capacity fits Linux system + application + data logging for industrial, medical, and automotive aftermarket markets; industrial-grade NAND and wide temperature range hold up in outdoor and in-vehicle high-temperature environments. Selection advice: if 64 GB is not enough, the same series offers larger capacities (confirm Active status in the official table); note eMMC-to-host-controller compatibility, and request the compatibility list before ordering. Parameters verified against Delkin Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

IS21ES08GA-JQLI is an ISSI 8GB eMMC managed NAND memory in a 100-ball FBGA package - for embedded storage in industrial products: eMMC 5.0 interface, MLC NAND plus controller in one JEDEC package, HS200 single-data-rate transfer up to 200MB/s and HS400 dual-data-rate transfer up to 400MB/s, 2.7V to 3.6V VCC with 1.8V or 3.3V VCCQ, -40C to 85C industrial range. The integrated controller is the selection point: it handles ECC, wear leveling, bad-block management and read sensing internally, so the host needs only a standard eMMC interface instead of raw-NAND firmware. Business impact: managed NAND removes months of flash-translation-layer development and field-failure risk, so industrial designs reach production with a qualified storage block rather than a custom NAND stack. Selection advice: the JQLI code is the 100-ball FBGA (14mm x 18mm) industrial variant - for the 153-ball package pick the JCLI code; enable the pseudo-SLC enhanced mode when endurance matters more than capacity, and confirm the host controller supports HS200 or HS400 before expecting peak rates. Ranked #10 on the hqew.com yesterday-hot list (2026-10-16). Parameters verified against ISSI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

The Swissbit SFEM256GB2ED1TB-I-VG-111-STD is a 256 GB eMMC 5.1 from the EM-30 series, built on industrial-grade 3D TLC NAND in a 153-ball BGA package with an industrial temperature range of -40°C to +85°C. The eMMC 5.1 HS400 interface and on-board controller implement bad-block management, wear leveling, and ECC in hardware, so the host needs no flash-management software — it is ready to use once soldered. The 256 GB capacity covers system-plus-data storage for HMIs, in-vehicle infotainment, and industrial gateways, while industrial-grade NAND, wide temperature range, and Swissbit's long supply horizon suit projects with 5–10-year lifecycles. Swissbit's official host-chipset compatibility document for the EM-30 series lists this exact part number as the 256 GB industrial model. Selection advice: the EM-30 series also offers a 128 GB option (SFEM128GB2ED1TB-I-EF-111-STD) — choose by capacity need; note eMMC is a soldered package, so rework requires hot-air equipment. Parameters verified against Swissbit documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

24LC256-I/SN is a 256 Kb I2C serial EEPROM from Microchip Technology in an 8-pin SOIC package, for nonvolatile storage of calibration data, configuration and event logs in industrial systems. Its advantage is the I2C bus: two wires, multiple devices per bus and byte-level write granularity, which keeps the storage subsystem simple and cheap. Selection advice: the I/SN suffix denotes the industrial temperature grade in SOIC-8 — the 24LC256 ships in several packages and grades, so match the full code to your footprint and operating range. EEPROM has finite write endurance, so confirm your write-cycle budget during design; for high-write-frequency logging, consider FRAM instead. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AS4C512M16D3LA-12BIN is an Alliance Memory 8Gb (512M x 16) DDR3L SDRAM in 96-ball FBGA dual-die package — for embedded compute, networking and industrial boards needing a second-source DDR3L option: routers, displays and control platforms. 1.35V low-voltage operation at 800MHz (DDR3L-1600) cuts rail power versus 1.5V DDR3 while keeping JEDEC DDR3L timing compatibility, and the x16 organization builds 16- or 32-bit buses with one or two chips. Selection advice: the -12 suffix is the 800MHz speed bin (for 933MHz/1866MT/s specify the -10 bin); the IN suffix is the industrial -40 to +95°C grade — commercial (CN) and automotive (AN) grades use different suffixes, so match the full code to your temperature requirement. Alliance positions this as a Micron MT41K512M16 drop-in alternative — verify ball-out and timing against your controller before swapping. With DRAM pricing in an up-cycle, lock allocation early on DDR3L programs rather than chasing spot lots. Parameters verified against Alliance Memory documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AT21CS11 is a Microchip Technology 1-Kbit (128 x 8) single-wire, I/O-powered serial EEPROM with a unique factory-programmed 64-bit serial number — for identifying and authenticating remote items such as cartridges, cables and disposable attachments where only two wires (SI/O plus ground) can reach the device. The single-wire interface is the selection point: one SI/O pin carries both power (drawn from the pull-up) and data, so a detachable accessory needs no extra connector pins, battery or regulator — and the 2.7 V to 4.5 V self-powered range suits Li-ion-powered devices, versus the AT21CS01 which covers 1.7 V to 3.6 V. It runs up to 125 kbps in high-speed mode, with 8-byte page writes, a 5 ms self-timed write cycle, 1,000,000 write-cycle endurance, 100-year data retention, IEC 61000-4-2 Level 4 ESD protection, and -40°C to +85°C operation. Four 256-bit zones can each be permanently locked read-only, and the 256-bit security register carries the factory serial number plus user-programmable lockable bytes, which is what makes the part an anti-counterfeit and warranty-tracking device rather than a plain memory. Selection advice: choose AT21CS11 over AT21CS01 when the pull-up rail is 2.7 V to 4.5 V; choose it over a 2-wire I2C EEPROM when pin count, connector cost or detachable-assembly simplicity matters more than bus speed. The base MPN covers several packages (2-pad XSFN, 3-lead SOT-23, 8-lead SOIC, 4-ball WLCSP), so quote the full ordering code (e.g. SSH10 for SOIC-8) to match your footprint and assembly process. Featured on Mouser New Products (2026-10-15). Parameters verified against Microchip Technology documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AT24C02C-SSHM-T is a Microchip 2Kbit (256 x 8) I2C-compatible 2-wire serial EEPROM in 8-pin SOIC (0.154 in narrow, SS), tape-and-reel packing (T) — 1.7 V to 5.5 V supply, up to 1 MHz clock, 550 ns access time, 5 ms self-timed write cycle, 16-byte page writes, hardware write-protect pin, Schmitt-trigger filtered inputs for noise suppression, 1 M endurance cycles and 100-year data retention, −40 to +85 °C. The 1.7 V floor is the selection point: it shares the rail with 1.8 V logic without a separate regulator, and the standard two-wire I2C protocol with hardware write protection makes it the default configuration store for calibration data, MAC addresses and user settings across consumer and industrial products. Selection advice: the SS is the 8-pin SOIC; the T is tape and reel — the AT24C02C-SSHM-B is the tube-packaged twin for prototype lines. The 2Kbit density fits the single-device address space without paging tricks; for larger stores move up the AT24C family and mind the addressing differences. Microchip lists AT24C02C-SSHM-T as Active. Evidence: Microchip AT24C02C datasheet and distributor listings confirm 2Kbit, 1.7–5.5 V, 1 MHz, 8-SOIC and tape-and-reel packing. Match the full AT24C02C-SSHM-T code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AT24C02D-SSHM-T is a 2 Kb I2C serial EEPROM from Microchip Technology in an 8-pin SOIC package — for storing small configuration blocks, calibration constants and device IDs. The 2 Kb density is the selection point: the smallest standard EEPROM for tiny parameter sets, at the lowest cost per device. Selection advice: the SSHM-T suffix denotes the SOIC-8 package on tape and reel — the AT24C02D ships in several packages, so match the full code to your layout. Confirm your storage need against the 2 Kb capacity; if your parameter set may grow, step up to a larger density in the same family now rather than respinning later. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AT24C256C-SSHL-T is a Microchip Technology 256 Kb I2C serial EEPROM in SOIC-8, tape and reel — for calibration data, configuration tables and event logs in industrial and consumer systems. 1 MHz I2C, a 5 ms write cycle and 1.7 V to 5.5 V operation is the selection point: fast bus speed plus a supply range covering both 1.8 V logic and 5 V legacy rails on one part — the 1.7 V floor means reads and writes keep working as a battery discharges toward empty. Selection advice: the −T suffix denotes tape and reel for SMT lines; for prototype quantities ask about cut-tape options in your RFQ; the SSHL code pins the SOIC-8 package — quote the full ordering code to match your footprint. EEPROM write endurance is finite, so budget write cycles during design; for high-frequency data logging, ask about FRAM alternatives in your RFQ. The 1 MHz Fast-mode Plus rate doubles the classic 400 kHz EEPROM ceiling — mind pull-up and bus capacitance in layout, as Fm+ is less forgiving than standard mode. Microchip lists this part as Active through distribution. Parameters verified against distributor and manufacturer documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Microchip lists AT24C64D-SSHM-T as In Production — a 64Kbit I2C serial EEPROM in SOIC-8, 1 MHz clock, 1.7V to 5.5V, -40 to 85 °C, tape and reel. The 64 Kbit density with 1 MHz I2C is the selection point: roomy enough for event logs and multi-page configuration with fast bus transfers. Selection advice: the SSHM-T suffix denotes SOIC-8 on tape and reel — match the full code to your layout and assembly process. EEPROM write endurance is finite, so confirm your write-cycle budget during design. Parameters verified against the Microchip official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Micron has committed over 75% of its 2027 output to long-term agreements — 26 LTAs, $32B in customer deposits, $150B in remaining obligations. What got locked, how it squeezes spot buyers, and five procurement moves.

Reports say Apple agreed to a multi-year NAND deal with Kioxia with no price cap — 'lock volume first, argue price later' becomes the industry playbook. What was reported, why Apple did it, and three signals for ordinary buyers.

CXMT is building a NAND R&D line while YMTC samples DRAM — China's memory 'division of labor' is breaking down. What was reported, when supply could be real, and three practical takeaways for buyers.