ICM-42670-P

BMI270 is a Bosch Sensortec ultra-low-power 6-axis IMU — for wearables and hearables where every microamp counts: 16-bit triaxial accelerometer (±2/±4/±8/±16 g) plus 16-bit triaxial gyroscope (±125 to ±2000 dps) in a 2.5 x 3.0 mm LGA-14, with gesture, context and activity recognition running in a 30 µA ultra-low-power domain. The plug-and-play step counter is optimized for wrist-worn devices, and motion-triggered interrupts let the host stay in deep sleep until something actually happens. Selection advice: the BMI270 is the wearable-optimized member of the BMI260 family — for smartphone-grade performance the BMI260 suits better; for drone and robotics vibration robustness the BMI088 is the alternative. Two application-specific variants exist (gesture vs context/activity) — match the firmware variant to your use case. Parameters verified against Bosch Sensortec documentation and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LSM6DSLTR is a 6-axis inertial measurement unit from STMicroelectronics — a 3-axis accelerometer plus a 3-axis gyroscope in a single LGA-14 package — for motion sensing in phones, wearables, drones and industrial equipment. Its advantage is integration: one package, one qualification and one sourcing line replace two discrete sensors, saving board space and simplifying the BOM. Selection advice: the TR suffix denotes tape-and-reel packing for automated assembly — confirm your required packing format in the RFQ, as the same device can ship on reel or in tray depending on the lot. ST IMU portfolio has many neighboring variants, so match the complete LSM6DSLTR ordering code against your BOM rather than substituting a similar-looking IMU. State quantity, packing and date-code requirements with your RFQ and we reconfirm the offered lot before quotation, replying within 24 hours.

LSM6DSV16XTR is an STMicroelectronics 6-axis IMU with embedded machine learning — for always-on motion sensing where the host processor should stay asleep: 3-axis accelerometer (±2/±4/±8/±16 g) plus 3-axis gyroscope (±125 to ±4000 dps) with a machine-learning core and finite-state machine that run gesture, activity and context recognition on-chip. The triple-channel architecture processes UI, OIS and EIS data independently, and embedded Qvar charge-variation detection adds tap and swipe interfaces without extra hardware. Selection advice: the MLC/FSM is the reason to pick this over the LSM6DSL — if your design does not need on-chip AI, the older parts cost less; for camera stabilization designs confirm whether you need the OIS/EIS dedicated channels. I2C, SPI and MIPI I3C interfaces cover all host types. Parameters verified against STMicroelectronics documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LSM6DS3TR-C is a 6-axis inertial measurement unit from STMicroelectronics in an LGA-16 package, with accelerometer and gyroscope — for motion sensing in phones, wearables and industrial devices. The always-on low-power 6-axis sensing is the selection point: it became the reference mobile IMU, with the TR-C suffix marking the tape-and-reel production variant. Selection advice: the TR suffix denotes tape and reel — match the full LSM6DS3TR-C code for production orders. Confirm your full-scale range and power budget against the datasheet; for newer designs, compare against the LSM6DSO family. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ICM-42688-P is a low-noise 6-axis gyroscope and accelerometer from TDK InvenSense in an LGA-14 package — for drones, robotics, wearables and image stabilization. The low-noise 6-axis IMU with on-chip sensor fusion support is the selection point: it delivers stable orientation output for motion tracking without a separate co-processor. Selection advice: confirm your full-scale range and output data rate requirements against the datasheet — the P variant targets high-performance applications versus cost-optimized IMUs. Verify your interface (I2C/SPI) and power budget. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ICM-20948 is a 9-axis motion-tracking IMU from TDK InvenSense in a QFN-24 package — gyroscope, accelerometer and magnetometer in one chip, marked Production but Not Recommended for New Designs. The integrated 9-axis sensing was the selection point: full orientation tracking from a single device for drones and AR/VR controllers. Selection advice: because TDK flags this part NRND, treat it as a legacy reference — for new designs qualify a current-production 9-axis IMU before committing the BOM; for existing builds, send quantity and date-code requirements with your RFQ and we will check remaining traceable stock. Parameters verified against the TDK official product page. We reconfirm the offered lot before quotation and reply within 24 hours.

MPU-6050 is a TDK InvenSense 6-axis MEMS motion-tracking device in QFN-24 (4.0 x 4.0 x 0.9 mm) — 3-axis gyroscope (±250/500/1000/2000 °/s) plus 3-axis accelerometer (±2/4/8/16 g) with 16-bit ADCs, an on-chip Digital Motion Processor (DMP) engine, 1024-byte FIFO, digital temperature sensor, 10,000 g shock tolerance and an auxiliary master I2C bus for external magnetometers, VDD 2.375–3.46 V with a separate VLOGIC pin setting the I2C interface levels (1.71 V to VDD). The DMP plus FIFO is the selection point: motion-fusion, gesture and timing work runs on-chip while the host sleeps, which is why this part defined the Arduino/drone gimbal era of low-cost IMUs. Selection advice: the MPU-6050 supports I2C only — if you need SPI, the MPU-6000 is the pin-compatible twin with SPI plus a single supply pin; do not treat them as code-identical. TDK lists MPU-6050 as Obsolete — production has stopped and final shipment is complete, so treat any offer as end-of-life stock: require date-code traceability and, for new designs, evaluate the current TDK IMU family instead. Evidence: InvenSense MPU-6000/MPU-6050 product specification (Rev. 3.4) and TDK product pages confirm the ranges, VDD, VLOGIC, QFN-24 and obsolete status. Match the full MPU-6050 code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MPU-9250 is a TDK InvenSense 9-axis MEMS motion-tracking device in QFN-24 (3.0 x 3.0 x 1.0 mm) — a multi-chip module combining a 3-axis gyroscope (±250/500/1000/2000 °/s) and 3-axis accelerometer (±2/4/8/16 g) die with an AK8963 3-axis magnetometer (±4800 µT), an on-chip Digital Motion Processor (DMP), dedicated auxiliary I2C sensor bus, I2C up to 400 kHz and SPI interfaces, VDD 2.4–3.6 V with VLOGIC 1.71 V to VDD, −40 to +85 °C. The single-package 9-axis integration is the selection point: accel plus gyro plus compass plus DMP in a 3 x 3 mm footprint, which is why this part powered the drone and wearable generation that needed orientation output from one chip. Selection advice: TDK lists MPU-9250 as Obsolete and recommends the ICM-20948 as the alternate — TDK own migration note stresses it is a superset/subset hardware change and not code-compatible, so treat any MPU-9250 offer as end-of-life stock with date-code traceability and plan new designs on the ICM-20948 register set instead of assuming register-level compatibility. Evidence: TDK/InvenSense MPU-9250 product specification (Rev. 1.1) and distributor listings confirm the 9-axis ranges, AK8963 compass, QFN-24 and obsolete status. Match the full MPU-9250 code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADXL345BCCZ is a digital three-axis accelerometer from Analog Devices in a 14-pin LGA package — for motion detection, tilt sensing, tap/double-tap input and free-fall detection in handheld, wearable and industrial devices. Its advantage is the built-in activity/inactivity and tap sensing: motion events wake the host from sleep without continuous polling, which cuts system power in battery designs. Selection advice: the CCZ suffix denotes the LGA-14 package on tape and reel — the ADXL345 ships in several packages, so match the full code to your layout. For new designs, compare against current-generation accelerometers on power and noise if your budget allows; for existing designs, match the code exactly. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADXL345BCCZ-RL is a 3-axis digital accelerometer from Analog Devices in production status, in a 14-lead LGA package with selectable ±2/±4/±8/±16 g ranges and SPI/I2C digital output on tape and reel — for motion sensing, tilt detection and activity monitoring. The selectable g-range with digital output is the selection point: one part covers both high-sensitivity tilt and high-g shock detection, which is why the ADXL345 became the reference hobbyist accelerometer. Selection advice: the BCCZ-RL suffix denotes the LGA-14 package on tape and reel — match the full ADXL345BCCZ-RL code. Confirm your range and interface against the datasheet. Parameters verified against the Analog Devices official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.