STM32H747XIH6

RP2040 is a Raspberry Pi dual-core Arm Cortex-M0+ microcontroller with programmable I/O in QFN-56 — for maker, education and cost-sensitive embedded designs: custom keyboards, sensor hubs and control panels. The dual cores plus PIO state machines are the selection point: deterministic I/O timing without bit-banging, at a price near 8-bit MCUs. Selection advice: RP2040 is the chip — for a finished module with flash and USB, consider the Pico board; for production, budget external QSPI flash in your BOM. The huge community and MicroPython support make it the fastest path for small teams. Parameters verified against the Raspberry Pi official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

RP2350A is a Raspberry Pi dual-core microcontroller selectable at boot between Arm Cortex-M33 and open-source Hazard3 RISC-V — for maker, education and industrial designs that want architecture choice without board spins: 150 MHz dual cores, 520 KB SRAM, 30 GPIO, and three PIO blocks for bit-banged protocols in a 7x7 mm 60-pin QFN. The headline over the RP2040 is security — TrustZone, signed boot and glitch detectors — plus HSTX high-speed serial output for DVI/HDMI. Selection advice: the A variant is the 60-pin QFN — for 48 GPIO the B variant (QFN-80) is the larger twin; the RP2354 adds 2 MB stacked flash for XiP-free designs. RP2350A is pin-compatible with the RP2040 — existing Pico footprints drop in, but confirm the power-supply sequencing against the datasheet. Parameters verified against Raspberry Pi documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L293D is an STMicroelectronics push-pull four-channel H-bridge motor driver with internal clamp diodes in 16-pin PowerDIP — for small DC motors, steppers and relay coils: robot kits, toys and lab fixtures. 600 mA per channel with 4.5–36 V supply is the selection point: driving motors straight from logic pins with no external diodes. Selection advice: the D suffix denotes the internal clamp diodes — the key reason to pick the L293D over the L293; for higher currents, the L298N or modern integrated drivers are the step up. Mind the ~2 V saturation drop in your motor voltage budget. Parameters verified against the ST official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L6386ED013TR is an ST high-voltage high-side and low-side gate driver — SO-14, 600 V max bootstrap, 400 mA source / 650 mA sink, embedded comparator, bootstrap diode, tape and reel. The embedded comparator plus bootstrap diode is the selection point: current sensing and high-side supply in one driver — fewer external parts for 600 V half-bridge stages. Selection advice: ST lists the L6386ED013TR as Active. The ED013TR suffix pins the SO-14 package on tape and reel — match it to your footprint; the L6387 variant is the SO-8 version with fewer pins. Verify the 400 mA/650 mA drive against your MOSFET gate charge at the switching frequency. Evidence: ST data confirms Active, SO-14, 600 V bootstrap, drive currents, embedded comparator. Match the full L6386ED013TR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L6387ED013TR is an ST high-voltage high-side and low-side gate driver — SO-8, 600 V max, 400 mA source / 650 mA sink, embedded comparator, bootstrap diode, interlocking and current-sense support, tape and reel. The SO-8 package is the selection point: 600 V half-bridge drive in an 8-pin footprint — the compact sibling of the SO-14 L6386 for space-constrained power stages. Selection advice: ST lists the L6387ED013TR as Active. The ED013TR suffix pins the SO-8 package on tape and reel — match it to your footprint; the L6386 is the larger SO-14 variant. Verify the 400 mA/650 mA drive against your MOSFET gate charge at the switching frequency. Evidence: ST data confirms Active, SO-8, 600 V, drive currents, embedded comparator. Match the full L6387ED013TR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L6390DTR is an ST half-bridge gate driver — SO-16, 600 V high-side rail, 290 mA source / 430 mA sink, 50 V/ns dV/dt immunity, UVLO, tape and reel. The 50 V/ns dV/dt immunity is the selection point: robust half-bridge drive for fast-switching MOSFETs where high dv/dt causes false triggering in weaker drivers. Selection advice: ST lists the L6390DTR as Active. The DTR suffix denotes SO-16 on tape and reel — match it to your footprint. Verify the 290 mA/430 mA drive against your MOSFET gate charge at the switching frequency — for larger switches step up to a higher-current driver. Evidence: ST data confirms Active, SO-16, 600 V rail, drive currents, 50 V/ns immunity. Match the full L6390DTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L6391DTR is an ST high/low-side gate driver — SO-14, 600 V high-side rail, 290 mA source / 430 mA sink, integrated bootstrap diode, adjustable deadtime, interlocking, smart shutdown and fault-protection comparator, tape and reel. The integrated protection set is the selection point: adjustable deadtime, interlocking and smart shutdown in one driver — a protected half-bridge without external logic. Selection advice: ST lists the L6391DTR as Active. The DTR suffix denotes SO-14 on tape and reel — match it to your footprint; the L6390 is the SO-16 sibling without the full protection set. Verify the 290 mA/430 mA drive against your MOSFET gate charge at the switching frequency. Evidence: ST data confirms Active, SO-14, 600 V rail, drive currents, integrated bootstrap diode and protection features. Match the full L6391DTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

L9945TR is a STMicroelectronics automotive 8-channel configurable MOSFET pre-driver in TQFP64-EP — for 12 V/24 V body and powertrain loads: drives 8 half-bridges or equivalent high/low-side combinations, 3.8–36 V battery supply range, SPI control and diagnostics, AEC-Q100 qualified. One device replaces multiple discrete gate-driver ICs, cutting BOM lines and PCB area in multi-channel switching modules such as seat, lighting and pump controllers. Selection advice: the TR code is tape and reel — channel configurability (half-bridge, full-bridge, high-side) is set via SPI at initialization; for a fixed 3-phase BLDC function consider a dedicated 3-phase driver instead. Ranked #7 on the Chuangxin Index July 2026 breakout list (1,900 searches, +393.51% MoM). Parameters verified against STMicroelectronics documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ST3485ECDR is an STMicroelectronics 3.3 V half-duplex RS-485/RS-422 transceiver in SO-8, tape and reel — guaranteed data rate of at least 12 Mbps, ±15 kV HBM / ±8 kV IEC 61000-4-2 contact ESD, standard 75176 pinout, 1 µA shutdown mode, −7 V to +12 V common-mode range, rated 0 °C to +70 °C. The 3.3 V supply with true 12 Mbps is the selection point: it runs directly from a 3.3 V MCU rail with no level translation, while older 5 V-only transceivers force an extra regulator or translator onto the board. Selection advice: the ECDR code is the commercial-temperature SO-8 reel version — the ST3485EBDR is the −40 °C to +85 °C industrial version in the same SO-8 footprint and a direct drop-in for wider ambient ranges; the ST3485ECN is the DIP-8 tube version for through-hole builds only. ST lists this code Active and shows stock on its official store; DigiKey also lists it as Active and available for ordering. Evidence: the ST official store page and ST3485 datasheet confirm the ordering code, 12 Mbps, ±15 kV ESD, SO-8 reel and Active status. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

STGAP2DMTR is an ST 1700 V isolated dual-channel gate driver — SO-16, 4 A drive, UVLO protection, galvanic isolation between gate drive signals, tape and reel. The 1700 V isolation is the selection point: dual-channel isolated drive for high-voltage SiC and IGBT stages — industrial drives and solar inverters where 600 V drivers cannot go. Selection advice: ST lists the STGAP2DMTR as Active. The DMTR suffix denotes SO-16 on tape and reel — match it to your footprint; the STGAP2SM is the single-channel narrow-body SO-8 sibling. Verify the isolation working voltage against your safety standard — 1700 V rating suits 1200 V-class power stages. Evidence: ST data confirms Active, 1700 V isolation, dual channel, SO-16, 4 A. Match the full STGAP2DMTR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.