AD9361BBCZ

CC1101RGPR is a sub-1 GHz RF transceiver from Texas Instruments in a 20-pin VQFN package, designed for low-power wireless links in metering, sensor networks, remote controls and home automation. Its advantage is the sub-1 GHz band: longer range and better obstacle penetration than 2.4 GHz for the same power budget, which is why it remains a workhorse for long-life battery-powered nodes. Selection advice: RGP denotes the VQFN-20 package and the trailing R tape-and-reel packing — match the full CC1101RGPR code to your BOM, since the CC1101 family ships in several package and packing combinations. RF performance depends on the matching network and antenna design around the chip, so this part is a component choice, not a drop-in module; confirm your region frequency-plan requirements when you RFQ. We reconfirm code, lot and traceability before quotation and reply within 24 hours.

AD620BRZ-R7 is an Analog Devices instrumentation amplifier in 8-lead SOIC_N, 7-inch tape and reel — gain set from 1 to 10,000 with a single external resistor, ±2.3 V to ±18 V dual supply (4.6 V to 36 V single), 15 µV maximum input offset (B grade), 1 MHz bandwidth, 1.3 mA maximum supply current, rated −40 °C to +85 °C. The single-resistor gain setting is the selection point: bridge sensors, thermocouples and strain gauges get a precision differential front end with one resistor instead of a matched-resistor op-amp network that drifts with temperature and layout. Selection advice: BRZ is the B grade (tighter offset than the A-grade AD620ARZ-R7), R-8 the SOIC package, R7 the 7-inch reel — the AD620BRZ-RL is the identical die on a 13-inch reel if your line prefers larger reels. DigiKey lists this code Active. Evidence: the ADI AD620 datasheet Rev. H ordering guide confirms the ordering code, B grade, 7-inch reel and −40 to +85 °C rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7192BRUZ-REEL is an Analog Devices 24-bit sigma-delta ADC with integrated PGA -- for precision measurement front ends: 2 differential or 4 pseudo-differential inputs, 4.7Hz to 4.8kHz output data rate, programmable gain from 1 to 128, 24-lead TSSOP, -40C to +105C. The on-chip low-noise gain stage lets small-amplitude sensor signals interface directly to the ADC without external amplification, and the automatic channel sequencer simplifies multi-channel acquisition firmware. Business impact: a complete analog front end in one device shrinks the signal chain BOM and board area for weigh scales, strain-gage transducers and PLC/DCS input modules -- fewer parts to qualify, fewer to source. Selection advice: the REEL suffix is the tape-and-reel packing for production -- for prototyping, the tube-packed AD7192BRUZ matches electrically; the 24-bit resolution is real only when the layout follows the datasheet grounding and decoupling guidance. Featured on the lcsc.com Lightning Deals list (2026-10-12). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7606BSTZ is an Analog Devices 8-channel, 16-bit simultaneous-sampling data acquisition system in LQFP-64 — for industrial DAQ: PLC analog inputs, power-line monitoring and vibration analysis. Eight truly simultaneous 16-bit channels is the selection point: phase-accurate multi-channel capture that multiplexed ADCs cannot deliver. Selection advice: the BSTZ suffix denotes LQFP-64 — confirm your input range and throughput against the datasheet; for fewer channels, the AD7606 family's 4/6-channel siblings cut cost. Plan the analog front end (filtering, protection) per ADI's reference circuits. Parameters verified against the ADI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8066ARZ is an Analog Devices dual 145 MHz FastFET operational amplifier in 8-lead SOIC, tube packing — 180 V/µs slew rate, 7 nV/√Hz voltage noise, 1 pA-class FET input bias current, 5 V to 24 V supply, rail-to-rail output, -40 °C to +85 °C. The FastFET input stage is the selection point: photodiode preamps and high-impedance sensor front ends get wideband speed without the noise penalty of bipolar inputs. Selection advice: ARZ is the SOIC-8 tube code — AD8066ARZ-R7 is the reel twin, and the single-channel AD8065 covers single-op-amp designs. Honest availability note: Mouser currently flags this code as restricted availability, so confirm the lot before committing to production volumes. Evidence: the ADI AD8066 official datasheet confirms the bandwidth, slew rate and package codes, and Mouser confirms the exact ordering code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD9245BCPZ-80 is an Analog Devices 14-bit, 80 MSPS pipelined ADC — for IF sampling and data acquisition: 73.3dB SNR, 3V single supply (2.7-3.6V), differential or single-ended input, parallel CMOS output, 32-lead LFCSP (5x5mm), -40°C to 85°C. The 80 MSPS rate with 14-bit resolution captures IF bands directly, so receiver designs drop a downconversion stage; pin-compatible 10/12-bit siblings allow one PCB to serve multiple performance tiers. Business impact: the AD9245 family has shipped for two decades with stable supply — a safe choice for long-lifecycle instrumentation. Selection advice: the -80 grade is the 80 MSPS speed bin — for 65 MSPS the -65 grade is cheaper; BCPZ is the LFCSP package — verify the land pattern against the ADI datasheet. Ranked #3 on the hqbuy.com real-time hot list (2026-10-13). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD9864BCPZ is an Analog Devices general-purpose IF digitizing subsystem in 48-lead LFCSP, tray packing — 10 MHz to 300 MHz IF input through a complete signal chain: low-noise amplifier, mixer, band-pass sigma-delta ADC and programmable decimation filter, with baseband I/Q serial digital output in 16 or 24 bits, on-chip LO and sample-clock synthesizers, SPI programming, 7.5 dB single-sideband noise figure, −7.0 dBm input third-order intercept, 12 dB continuous AGC range, 2.7 V to 3.6 V single supply at 17 mA typical, rated −40 °C to +85 °C. The single-chip IF-to-bits chain is the selection point: receiver designs that would otherwise need a discrete LNA, mixer, ADC and clock tree get the whole front end in one 7×7 mm package, which is why this part anchors legacy communications and instrumentation platforms. Selection advice: BCPZ is the tray version (260 per tray) — the AD9864BCPZRL is the identical device on 13-inch reel (2,500 per reel) for volume lines. ADI does not show a lifecycle status on the product page; DigiKey lists this code Active with stock, and no ADI discontinuance notice covers the AD9864 (PDN 21_0100 discontinued the AD9860/AD9862, not this part). Evidence: the ADI AD9864 datasheet Rev. B ordering guide confirms the ordering code, 48-lead LFCSP, tray packing and −40 to +85 °C rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADA4077-2ARZ is an Analog Devices dual precision operational amplifier in 8-lead SOIC, tube packing — 15 µV typical input offset (50 µV max A-grade), 0.25 µV/°C drift, 3.6 MHz gain-bandwidth, 1.2 V/µs slew rate, 1 nA input bias and 400 µA per channel, specified over −40 °C to +125 °C on 5 V to 30 V supplies (±2.5 V to ±15 V). Unity-gain stable with no phase reversal and stable into 1000 pF capacitive loads. The offset-plus-drift combination is the selection point: thermocouple, RTD and strain-gauge front ends hold calibration across temperature without trimming, which is the whole value proposition of a precision op amp. Selection advice: the ARZ code is the tube version — ARZ-R7/ARZ-RL is the same die on tape and reel for pick-and-place; this is not a rail-to-rail output part, so size your signal swing inside the ±15 V rails. For single-channel or quad layouts use the ADA4077-1/ADA4077-4. Evidence: LCSC and element14/Newark listings confirm 15 µV, 3.6 MHz, −40 to +125 °C, SOIC-8 and wide distributor stock. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADM3053BRWZ is an Analog Devices isolated CAN transceiver in 20-lead wide-body SOIC — 2.5 kVRMS signal and power isolation with the integrated isoPower isolated DC-DC converter, powered from a single 5 V supply (no separate isolated supply needed), 5 V or 3.3 V operation on VIO, ISO 11898 compliant, up to 1 Mbps, slope control for reduced EMI, thermal shutdown, >25 kV/µs common-mode transient immunity, -40 to +85 °C, tube packing (Z). The integrated isolated power is the selection point: the whole isolated CAN node runs from one 5 V rail — the competing ADM3052 needs a separate bus-side supply. Selection advice: the BRWZ code is the tube-packed version — the BRWZ-RL code is tape-and-reel, so match the packing suffix to your assembly process. Unpowered nodes do not disturb the bus; up to 110 nodes are supported. Evidence: ADI ADM3053 datasheet (Rev. E) and distributor listings confirm 2.5 kVRMS, isoPower, 20-SOIC, 1 Mbps and tube packing. Match the full ADM3053BRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADM3054BRWZ is an Analog Devices isolated high-speed CAN transceiver — 16-lead wide-body SOIC, 5 kV rms signal isolation, bus protection, up to 1 Mbps, −40 to +125 °C. The integrated 5 kV isolation is the selection point: isolated CAN in one chip — no separate isolator plus transceiver, which halves the BOM for isolated CAN nodes. Selection advice: ADI lists the ADM3054BRWZ as Production. The BRWZ code pins the 16-lead wide-body SOIC — match it to your footprint. Verify the isolation working voltage against your safety standard, and note the isolated side needs its own supply — budget the isolated DC-DC in the BOM. Evidence: ADI data confirms Production, 16-lead wide-body SOIC, 5 kV rms isolation, 1 Mbps. Match the full ADM3054BRWZ code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Skyworks and Qorvo expect to close their $22 billion merger on or about October 5, 2026. What the deal changes for RF front-end buyers — and a five-point checklist for before and after close.