ADXL345BCCZ-RL

ADXL345BCCZ is a digital three-axis accelerometer from Analog Devices in a 14-pin LGA package — for motion detection, tilt sensing, tap/double-tap input and free-fall detection in handheld, wearable and industrial devices. Its advantage is the built-in activity/inactivity and tap sensing: motion events wake the host from sleep without continuous polling, which cuts system power in battery designs. Selection advice: the CCZ suffix denotes the LGA-14 package on tape and reel — the ADXL345 ships in several packages, so match the full code to your layout. For new designs, compare against current-generation accelerometers on power and noise if your budget allows; for existing designs, match the code exactly. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DS18B20 is an Analog Devices/Maxim 1-Wire digital thermometer — programmable 9–12 bit resolution, ±0.5 °C accuracy (−10 to +85 °C), −55 to +125 °C range, 3–5.5 V supply, 3-pin TO-92. The 1-Wire bus is the selection point: dozens of sensors share one MCU pin with unique 64-bit IDs — the default temperature sensor for multi-point monitoring. Selection advice: order-code warning — the bare DS18B20 (tin-lead, no + suffix) is listed as Obsolete and RoHS non-compliant by distributors; the lead-free DS18B20+ is the production variant (DigiKey lists it as the direct substitute with stock). For new designs always specify the DS18B20+ — the bare code will fail RoHS compliance. For parasite-power mode verify the pull-up and timing against the datasheet. Evidence: DigiKey confirms bare DS18B20 Obsolete/RoHS non-compliant and DS18B20+ as direct substitute; ADI data confirms 12-bit, ±0.5 °C, TO-92. Match the full code including the + suffix. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Analog Devices lists DS18B20+ as a PRODUCTION programmable-resolution 1-Wire digital thermometer, -55 to +125 °C range, ±0.5 °C accuracy (-10 to +85 °C), 9 to 12-bit resolution. The 1-Wire interface is the procurement advantage: dozens of sensors share a single data line with unique 64-bit IDs, which slashes wiring cost in multi-point temperature monitoring. Selection advice: the + denotes the lead-free configuration in the TO-92-3 through-hole package — the DS18B20 also ships in SO and other SMD packages, so match the full DS18B20+ code to your assembly process. Each device carries a factory-programmed unique ID, which your firmware uses for bus addressing; confirm your resolution setting (9–12 bit trades speed for precision) during design. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TMP36GT9Z is a voltage-output temperature sensor from Analog Devices in production status, in a TO-92 package — 10 mV/°C, ±2 °C accuracy, 2.7 to 5.5 V supply, -40 to +125 °C. The 2.7 V minimum supply is the selection point over the LM35: it runs from a single lithium cell or 3.3 V rail where the LM35 cannot. Selection advice: the GT9Z suffix denotes TO-92 in bulk packing — match the full TMP36GT9Z code. For 5 V-only designs the LM35 is the cheaper alternative; for low-voltage and battery designs, stay with the TMP36. Parameters verified against the Analog Devices official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

BMI270 is a Bosch Sensortec ultra-low-power 6-axis IMU — for wearables and hearables where every microamp counts: 16-bit triaxial accelerometer (±2/±4/±8/±16 g) plus 16-bit triaxial gyroscope (±125 to ±2000 dps) in a 2.5 x 3.0 mm LGA-14, with gesture, context and activity recognition running in a 30 µA ultra-low-power domain. The plug-and-play step counter is optimized for wrist-worn devices, and motion-triggered interrupts let the host stay in deep sleep until something actually happens. Selection advice: the BMI270 is the wearable-optimized member of the BMI260 family — for smartphone-grade performance the BMI260 suits better; for drone and robotics vibration robustness the BMI088 is the alternative. Two application-specific variants exist (gesture vs context/activity) — match the firmware variant to your use case. Parameters verified against Bosch Sensortec documentation and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ICM-42670-P is a TDK InvenSense 6-axis MotionTracking IMU combining 3-axis gyroscope and 3-axis accelerometer in 2.5x3 mm LGA-14 — for high-performance motion sensing in industrial robotics, AR/VR headsets and gaming controllers. 16-bit resolution, ±2/4/8/16 g accelerometer ranges, I3C/I2C/SPI interfaces, 550 µA operating current, and -40 to +85°C range. Ranked #16 on the 创芯指数 March 2026 hot-search TOP 50 with 22,506 searches and a 222.90% month-on-month increase, as IMU demand extends from consumer into robotics and drones. Selection advice: the -P code is the standard LGA-14 package — at 0.55 mA in low-noise mode it undercuts the ICM-42688-P (0.88 mA) for battery-powered designs; the I3C interface suits new sensor hubs while I2C keeps legacy compatibility. Parameters verified against TDK InvenSense documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ICM-42688-P is a low-noise 6-axis gyroscope and accelerometer from TDK InvenSense in an LGA-14 package — for drones, robotics, wearables and image stabilization. The low-noise 6-axis IMU with on-chip sensor fusion support is the selection point: it delivers stable orientation output for motion tracking without a separate co-processor. Selection advice: confirm your full-scale range and output data rate requirements against the datasheet — the P variant targets high-performance applications versus cost-optimized IMUs. Verify your interface (I2C/SPI) and power budget. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LSM6DSLTR is a 6-axis inertial measurement unit from STMicroelectronics — a 3-axis accelerometer plus a 3-axis gyroscope in a single LGA-14 package — for motion sensing in phones, wearables, drones and industrial equipment. Its advantage is integration: one package, one qualification and one sourcing line replace two discrete sensors, saving board space and simplifying the BOM. Selection advice: the TR suffix denotes tape-and-reel packing for automated assembly — confirm your required packing format in the RFQ, as the same device can ship on reel or in tray depending on the lot. ST IMU portfolio has many neighboring variants, so match the complete LSM6DSLTR ordering code against your BOM rather than substituting a similar-looking IMU. State quantity, packing and date-code requirements with your RFQ and we reconfirm the offered lot before quotation, replying within 24 hours.

LSM6DSV16XTR is an STMicroelectronics 6-axis IMU with embedded machine learning — for always-on motion sensing where the host processor should stay asleep: 3-axis accelerometer (±2/±4/±8/±16 g) plus 3-axis gyroscope (±125 to ±4000 dps) with a machine-learning core and finite-state machine that run gesture, activity and context recognition on-chip. The triple-channel architecture processes UI, OIS and EIS data independently, and embedded Qvar charge-variation detection adds tap and swipe interfaces without extra hardware. Selection advice: the MLC/FSM is the reason to pick this over the LSM6DSL — if your design does not need on-chip AI, the older parts cost less; for camera stabilization designs confirm whether you need the OIS/EIS dedicated channels. I2C, SPI and MIPI I3C interfaces cover all host types. Parameters verified against STMicroelectronics documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS37002LMABTR-050B5 is an isolated Hall-effect current sensor from Allegro MicroSystems in a 16-pin SOIC package, with a 50 A measurement range on tape and reel — for high-current motor drives, solar inverters and industrial power. The 50 A range in a standard SOIC-16 is the selection point: high-current isolated sensing without a bulky module or external shunt. Selection advice: the 050B5 code denotes the 50 A bidirectional variant — the ACS37002 ships in multiple ranges that are not interchangeable, so match the full ACS37002LMABTR-050B5 code. Confirm your current range, bandwidth and isolation requirements against the datasheet. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.