LM358DGKR

LM358P is a Texas Instruments LM358 dual operational amplifier in PDIP-8, tube packaging — single supply 3 V to 32 V (or ±1.5 V to ±16 V dual), input common-mode range includes ground, unity-gain stable, two independent op-amps on one die. The PDIP-8 package is the selection point: through-hole for breadboards, teaching labs, prototyping and legacy repairs — the same LM358 die ships in SOIC, TSSOP and VSSOP under different suffixes, so match the full LM358P code to your board. Selection advice: the ground-sensing input of the LM358 is why it survives in single-supply sensor front ends where older op-amps cannot swing low enough — pick it for comparators, active filters and transducer amplifiers on a single rail. It is not rail-to-rail output and not precision (millivolt offsets), so for low-voltage precision work step up to a modern RRIO part. As the most remarked jellybean op-amp in the market, require lot traceability. Evidence: TI LM358 product page confirms PDIP-8, 3–32 V single supply and ground-sensing inputs. Match the full LM358P code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

LM358PWR is a Texas Instruments LM358 dual operational amplifier in TSSOP-8 on tape and reel — single supply 3 V to 32 V (or ±1.5 V to ±16 V dual), input common-mode range includes ground, unity-gain stable, two independent op-amps on a 3 × 4.4 mm footprint. The PWR code is the selection point: the same LM358 die as the PDIP-8 LM358P, but in thin-shrink SMD on reel for pick-and-place production — order PWR for volume builds, P for prototypes and hand assembly. Selection advice: the TSSOP-8 footprint is less than a third the board area of PDIP-8, which matters in dense sensor and control boards; electrically the parts are identical, so a design proven on LM358P ports to LM358PWR with only a footprint change. Same caveats as the family: not rail-to-rail output, millivolt offsets — for precision low-voltage work choose a modern RRIO op-amp. Evidence: TI LM358 product page confirms TSSOP-8 availability, 3–32 V single supply and ground-sensing inputs. Match the full LM358PWR code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

THS4121IDGNR is a Texas Instruments fully-differential amplifier — for single-ended to differential conversion and ADC driving: 100MHz -3dB bandwidth, 50V/µs slew rate, -75dB total harmonic distortion at 1MHz, 5.4nV/√Hz input-referred noise, differential input and output, 3.3V supply, 8-pin VSSOP package. The fully-differential signal path from input to output rejects common-mode noise and improves distortion, so high-speed ADCs get the clean drive they need without extra filtering stages. Business impact: differential ADC drivers are the bottleneck component in precision data-acquisition front ends — a catalog-standard part with long availability simplifies qualification and second sourcing. Selection advice: the DGNR code is the VSSOP-8 package — for MSOP with PowerPAD consider the DGK variant; the THS4121 is the no-power-down member — for shutdown capability consider the THS4120. Ranked #15 on the hqbuy.com real-time hot list (2026-09-28). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TLV9002IDGKR is a Texas Instruments dual rail-to-rail input/output operational amplifier in 8-pin VSSOP — for space-constrained low-voltage designs that need modern RRIO performance at commodity cost: smoke detectors, wearables and small appliances. 1.8 V to 5.5 V supply, 1 MHz gain bandwidth, 2 V/µs slew rate, 60 µA per channel, 5 pA input bias current, -40 to +125 °C. The CMOS RRIO architecture with EMI-hardened inputs is the selection point: true rail-to-rail operation on both input and output at 1.8 V, where bipolar parts cannot go, with integrated RFI filtering for noisy environments. Selection advice: this is the cost-optimized RRIO alternative to the LMV358 on this site — pick the TLV9002 for 1.8 V operation or smaller VSSOP footprint; the LMV358 covers the SOIC footprint at lower unit cost. The IDGKR code is the VSSOP-8 reel — confirm the 3 x 4.9 mm footprint against your layout. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Texas Instruments lists ADS1115IDGSR as an ACTIVE 16-bit delta-sigma ADC in VSSOP-10, with 860 SPS sampling, 4 multiplexed channels and I2C interface. The 16-bit resolution is the procurement-relevant advantage: it resolves small sensor signals that a 10- or 12-bit converter would bury in quantization noise, which is why this part is the default choice for precision data-acquisition front ends. Selection advice: the IDGSR suffix pins the VSSOP-10 package on tape and reel — the ADS1115 also ships in other packages, so match the full code to your layout. Four multiplexed inputs versus the two-channel ADS1113 and single-ended/differential options are the family decision points; confirm your channel count and interface (I2C here, not SPI) against the datasheet before substituting. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDGST is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter — four single-ended or two differential inputs, programmable gain amplifier with full-scale ranges from ±6.144 V down to ±0.256 V, programmable data rates from 8 to 860 SPS, I2C interface with four pin-selectable addresses, in 10-pin VSSOP, tube packing (DGST), -40 to +125 °C. The integrated PGA, low-drift reference and oscillator are the selection point: true precision ADC performance with no external reference or clock, ideal for battery-voltage monitoring, temperature measurement and portable instrumentation. Selection advice: 860 SPS suits slow precision signals — for kilohertz sampling choose an SAR ADC (ADS868x family) instead. The built-in comparator can drive an alert pin for threshold monitoring without MCU polling, and 16 I2C addresses (four pins × four states) let you run multiple converters on one bus. Note this exact ADS1115IDGST code is the tube variant; IDGSR is the reel version. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA ranges, 8-860 SPS, VSSOP-10 and tube packing. Match the full ADS1115IDGST code for packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IDYNR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin SOT-23 package — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing (DYNR), -40 to +125 °C. The SOT-23 footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in the smallest ADS1115 package for space-constrained sensor nodes. Selection advice: same die and performance as the VSSOP (IDGST) and X2QFN (IRUGR) variants — choose this code for the SOT-23 footprint and reel packing. The 150 µA active current and single-shot power-down mode suit battery designs; for 24-bit resolution or excitation sources step up to the ADS1220. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D) and distributor listings confirm 16-bit, PGA, I2C, SOT-23-10 and reel packing. Match the full ADS1115IDYNR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGR is a Texas Instruments ADS1115 16-bit delta-sigma analog-to-digital converter in the 10-pin X2QFN package (2 × 1.5 × 0.4 mm) — four single-ended or two differential inputs, programmable gain from ±6.144 V to ±0.256 V full-scale, 8 to 860 SPS, I2C with four pin-selectable addresses, tape-and-reel packing of 3000 (IRUGR; IRUGT is the small reel), -40 to +125 °C. The 2 × 1.5 mm footprint is the selection point: full 16-bit precision with PGA, internal reference and comparator in one of the smallest ADC packages available, for wearables and dense sensor boards. Selection advice: same die and performance as the VSSOP (IDGSR) and SOT-23 (IDYNR) variants — choose this code for the X2QFN footprint and 3000-reel packing. Leadless QFN needs reflow assembly and good layout practice; for hand-soldering prototypes choose the VSSOP variant. TI lists this code as Active. Evidence: TI ADS1115 datasheet (SBAS444D), TI pack addendum and DigiKey listings confirm 16-bit, PGA, I2C, X2QFN-10 and 3000-reel packing. Match the full ADS1115IRUGR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1115IRUGT is a Texas Instruments 16-bit delta-sigma ADC in 10-pin X2QFN (2.0 × 1.5 × 0.4 mm), 250-piece small reel — I2C interface, four single-ended or two differential inputs, programmable gain amplifier (±256 mV to ±6.144 V), internal low-drift reference and oscillator, programmable comparator, 8 to 860 SPS, 2.0–5.5 V, 150 µA, −40 °C to +125 °C. The integration is the selection point: PGA, MUX, reference, oscillator and comparator on one 2×1.5 mm die means a complete sensor front end with no external analog support chips. Selection advice: the RUG package code is the X2QFN — ADS1115IDGST is the same die in VSSOP-10 on 250-piece small reel — the easier-to-assemble alternative for designs that do not need the 2×1.5 mm X2QFN footprint, not interchangeable on the same footprint. Against the 12-bit ADS1015: pick the ADS1115 for resolution (weighing, precision sensing), the ADS1015 for speed (3300 SPS). The ADDR pin gives four I2C addresses, so up to four devices share one bus. Evidence: TI ADS1115 datasheet (ordering addendum) and distributor listings confirm X2QFN-10, 250-reel, 16-bit, I2C and −40 to +125 °C. Match the full ADS1115IRUGT code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADS1220IPW is a Texas Instruments ADS1220 24-bit delta-sigma analog-to-digital converter for small-signal sensors — programmable gain from 1 to 128 V/V, up to 2000 SPS with single-cycle settling, SPI-compatible interface, in 16-pin TSSOP, tube packing (IPW; IPWR is the reel version), -40 to +125 °C. The two programmable excitation current sources plus simultaneous 50/60 Hz rejection at 20 SPS are the selection point: complete RTD, thermocouple, bridge-sensor and weigh-scale front ends with no external current source or mains-noise filtering. Selection advice: 20-bit effective resolution suits precision instrumentation — for kilohertz sampling choose an SAR ADC instead. The internal 2.048 V reference, oscillator and temperature sensor cut the external BOM to near zero; for I2C instead of SPI choose the ADS1115 family. TI lists this code as Active. Evidence: TI ADS1220 datasheet (SBAS501D) and TI pack addendum confirm 24-bit, PGA 1-128, 2 kSPS, TSSOP-16 and tube packing. Match the full ADS1220IPW code for packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.