MX25L25645GMJ-08G

MX25L12835FMI-10G is Macronix’s 128-Mbit serial NOR flash — 16M × 8, SPI/QPI up to 104 MHz, 2.7–3.6 V, SOP-16 — for firmware storage and execute-in-place: MCU boot flash, OTA update partitions, and data logging. The ‘-10G’ is the 104 MHz speed grade; the wide 16-SOIC package suits hand-solderable and legacy layouts where fine-pitch packages are unwelcome. Selection advice: this is the tube-packed SOP-16 ordering code — for reel packing quote the /TR suffixed code. For new compact designs check Macronix’s smaller package options for the same die, since 16-SOIC costs board area. QPI quad-I/O roughly quadruples read throughput over standard SPI when the controller supports it — verify the MCU’s QSPI peripheral before counting on the headline speed. Active at distribution. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

The GigaDevice GD25Q256EFIK is a 256 Mb SPI NOR Flash with a 2.7 V–3.6 V supply, 133 MHz clock, SOP-16 300 mil package, and an industrial temperature range of -40°C to +85°C. It belongs to the same GD25Q family as the in-catalog GD25Q128E (128 Mb), so drivers and instruction sets are compatible — doubling capacity requires no software change; the widely used SOP-16 package keeps second sources easy to find. GigaDevice's official product page marks Status: MP (mass production), and the official datasheet (DS-00526, Rev 1.2), Section 9.1 Valid Part Numbers, lists this exact part number. Selection advice: the direct step-up when 128 Mb is no longer enough; note package/temperature-grade differences versus other GD25Q256E suffix variants (e.g. ESIG) and confirm the suffix when ordering. Parameters verified against GigaDevice documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

GD25Q128ESIGR is a GigaDevice 128 Mbit serial NOR Flash in SOP8 — for code and data storage in industrial control, IoT devices and automotive electronics where a proven 3 V SPI Flash is the default. 133 MHz SPI clock, Quad I/O up to 532 Mbit/s, 4 KB uniform sectors, 2.7 V to 3.6 V operation, and -40 to +85°C industrial grade. Ranked #40 on the 创芯指数 March 2026 hot-search TOP 50 with 12,738 searches, as NOR Flash pricing firms on automotive and industrial restocking. Selection advice: the ESIGR code is the SOP8 208mil reel version with industrial temperature — the EIGR is the commercial-grade alternative; against Winbond W25Q128JV this is the pin-compatible second source most buyers qualify in parallel. Parameters verified against GigaDevice documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

GD25Q64ETIGR is a GigaDevice 64Mb (8M x 8) serial NOR Flash in SOP-8 (150mil) - for firmware and code storage in industrial controllers, consumer electronics and telecom equipment. A 2.7V to 3.6V supply with single, dual and Quad SPI up to 133MHz is the selection point: Quad I/O moves boot code four bits per clock, which shortens boot time and frees host-controller pins versus parallel Flash. The business case is density-per-dollar at a mainstream node: 64Mb covers large firmware images with room for A/B update slots, while 100,000 program/erase cycles and 20-year data retention suit field equipment that must run for a decade without rework. Evidence: GigaDevice lists the GD25Q64E base family as MP (mass production) with an official datasheet, and the part carries hardware and software write protection plus program/erase suspend for safe over-the-air updates. Selection advice: the TIGR suffix pins the industrial temperature grade, SOP-8 150mil package and tape-and-reel packing - match the full code to your BOM, since the GD25Q64 family spans multiple packages and the similar GD25Q64C differs in feature set; confirm your host controller supports Quad SPI before assuming the full 133MHz rate, and for 1.8V-only rails specify a 1.8V GigaDevice family instead. Heat basis: Ranked #1 on hqbuy.com real-time hot list (2026-10-15). Parameters verified against GigaDevice documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

The ISSI IS25WP256D-RMLE-TR is a 256 Mbit serial NOR Flash on a 1.65 V–1.95 V supply, 104 MHz clock, 16-pin SOIC package, and a wide temperature range of -40°C to +105°C, supplied on tape and reel. The 1.8 V supply is purpose-built for low-power embedded systems: it connects directly to 1.8 V MCUs/SoCs and eliminates level-shifting parts; the -40 to +105°C range suits industrial and in-vehicle infotainment environments. ISSI's official datasheet includes the ordering-part-number nomenclature covering this exact device. Selection advice: compared with the 3 V IS25LP256 series, this is the 1.8 V variant — always confirm the system voltage rail before selecting; the -TR tape-and-reel code is the SMT volume-production option. Parameters verified against ISSI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MT25QL128ABA1ESE-0SIT is a 128 Mb quad-I/O serial NOR Flash from Micron Technology in an SOP2-8 package, for high-performance embedded storage — firmware images and execute-in-place code. Quad-I/O is the selection point over standard SPI flash: four data lines multiply the read throughput, which shortens boot time and enables execute-in-place without shadowing to RAM. Selection advice: confirm your controller supports quad-I/O mode before specifying this part — in single-SPI mode you pay for speed you cannot use. As firmware-critical flash, require lot and date-code traceability and state whether you need blank or pre-programmed devices in your RFQ. We reconfirm the offered lot before quotation and reply within 24 hours.

The Infineon S25HS512TFAMHV013 is a 512 Mbit NOR Flash from the SEMPER family with an HS-T interface, a 1.7 V–2.0 V supply, Quad SPI support, an extended temperature range of -40°C to +105°C, and a SOIC-16 package. The SEMPER family is engineered for functional safety and long-lifecycle designs, and Infineon's official product page marks this device Active and preferred with supply planned through 2037 — a fit for automotive and industrial programs requiring 10+ years of availability; the 1.8 V rail connects directly to low-power SoCs with no level shifting. Selection advice: compared with the 3 V S25FL512S, this is the 1.8 V low-voltage variant — confirm the system voltage rail before selecting; for -40 to +85°C commercial grade, the S25HS512TDPMHI013 is the alternative. Parameters verified against Infineon documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

The Winbond W25Q01JV is the highest-capacity device in the W25Q serial NOR Flash family at 1 Gbit, built on a uniform 4 KB sector architecture with Dual/Quad SPI interfaces running up to 133 MHz, a 2.7 V–3.6 V supply range, and an industrial temperature range of -40°C to +85°C. As the flagship capacity of the series, a single chip carries the full 1 Gbit of code storage, simplifying the BOM and PCB layout versus multi-chip cascaded schemes; the uniform 4 KB sectors make erase management finer and firmware upgrades more flexible, while high-speed Quad SPI read supports execute-in-place (XIP) and code shadowing for shorter system boot times. Winbond lists the device as Status=P (in production), so supply is stable for long-lifecycle industrial control, networking, and smart-terminal projects. Selection advice: if code size exceeds 512 Mb but has not reached multi-gigabit territory, the W25Q01JV is the direct step-up from the W25Q512JV with no interface change; note it is a 3 V device — 1.8 V low-power systems should pick a 1.8 V series instead; space-constrained designs can choose the TFBGA-24 6×8 mm package. Parameters verified against Winbond documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

The Winbond W25Q02JVTBIM is a 2 Gbit (256 MB) QSPI NOR Flash built on a stacked four-die × 512 Mbit architecture, with uniform 4 KB sectors, Standard/Dual/Quad SPI plus DTR (double transfer rate) modes, clocks up to 133 MHz (532 MHz equivalent in Quad mode), a 2.7 V–3.6 V supply, an industrial temperature range of -40°C to +85°C, and a 24-ball TFBGA 8×6 mm package. As the largest-capacity device in the W25Q family, a single chip covers large-code applications such as complex GUIs and OTA dual-image backup without external storage; DTR doubles effective throughput, so code shadowing and XIP run more smoothly. Winbond's official W25Q02JV datasheet (RevD, DTR) lists this exact part number in the ordering table as a valid in-production device. Selection advice: it is the direct step-up from the 1 Gb W25Q01JV with an interface-compatible footprint; note it is a 3 V device; the TFBGA package suits high-density layouts. Parameters verified against Winbond documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

W25Q128JVSIQ is a 128 Mb serial NOR Flash memory from Winbond in an 8-pin SOIC package, for code and data storage in embedded systems — firmware images, configuration tables and data logging. Its advantage is the standard SPI interface and JEDEC-compatible footprint, which keeps the memory subsystem interchangeable across controller platforms and simplifies second-sourcing. Selection advice: flash holds your firmware, so this is the wrong part to buy on price alone — confirm the exact 128 Mb density code and require date-code traceability, because wrong-density or remarked flash causes field failures that are expensive to recall. The SIQ suffix pins the SOIC-8 package; state whether you need blank or pre-programmed devices in your RFQ. We reconfirm manufacturer, density code, lot and traceability against the offered lot before quotation and reply within 24 hours.

Micron has committed over 75% of its 2027 output to long-term agreements — 26 LTAs, $32B in customer deposits, $150B in remaining obligations. What got locked, how it squeezes spot buyers, and five procurement moves.

Reports say Apple agreed to a multi-year NAND deal with Kioxia with no price cap — 'lock volume first, argue price later' becomes the industry playbook. What was reported, why Apple did it, and three signals for ordinary buyers.

CXMT is building a NAND R&D line while YMTC samples DRAM — China's memory 'division of labor' is breaking down. What was reported, when supply could be real, and three practical takeaways for buyers.