AD5761RARUZ

AD5689RBRUZ is an Analog Devices dual 16-bit buffered voltage-output DAC in 16-lead TSSOP — for precision setpoint and calibration outputs in industrial control: PLC I/O cards, data acquisition and optical transceiver biasing. ±2 LSB maximum INL at 16 bits, an internal 2.5 V reference with 2 ppm/°C typical drift (no external reference needed), user-selectable gain of 1 or 2 for 2.5 V or 5 V full scale, 20 mA drive capability within 0.5 V of the rails, and 50 MHz SPI with daisy-chain and readback. Power-on reset to zero or midscale keeps outputs safe at startup. Selection advice: the BRUZ code is the TSSOP-16 tube version — for single-channel designs the AD5683R is the family sibling; against the octal DAC80508 on this site, the AD5689R is the pick for dual-channel precision nodes where per-channel accuracy matters more than channel count. The 4 µA power-down mode suits battery-backed calibration circuits. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DAC11001A0PW is a Texas Instruments 20-bit SPI DAC in 48-pin TQFP — for precision control loops and waveform generation where 16-bit resolution leaves quantization visible: laser marking, premium audio and test instrumentation. The R-2R architecture delivers 1-LSB maximum DNL (guaranteed monotonic), 4-LSB maximum INL, 7nV/√Hz noise and 1µs settling, with code-independent 1nV-s glitch for clean waveform ramps. Selection advice: the 0PW code is the TQFP-48 package — this is the unbuffered voltage-output architecture, so pair it with a suitable output buffer for your load; the integrated precision feedback resistors simplify the output stage. The DAC11001B is the higher-accuracy grade for tighter linearity budgets. External reference sets the output range (VREFPF to VREFNF) — confirm your reference choice against the range requirements. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DAC80508ZRTER is a Texas Instruments octal 16-bit buffered voltage-output DAC in 16-pin WQFN — for multichannel precision control from one compact package: ATE pin electronics, optical module control and industrial I/O expansion. Eight channels with ±1 LSB maximum INL, an integrated 2.5 V reference (2 ppm/°C typical on the DAC80508 grade), user-selectable gains of ½, 1 or 2 for 1.25/2.5/5 V full scale, 20 mA drive per channel, and 50 MHz SPI with daisy-chain and CRC error check. Only 0.6 mA per channel at 5.5 V with per-channel power-down to 15 µA. Selection advice: the ZRTER code is the WQFN-16 large-reel version — the family is pin-compatible across 12/14/16-bit grades (DAC70508/DAC75508) so resolution can change without a layout spin; against the dual AD5689R on this site, the DAC80508 is the pick when channel count dominates over per-channel trim accuracy. Reset to zero or midscale is pin-selectable at power-up. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD4003BRMZ is an Analog Devices 18-bit, 2 MSPS successive-approximation ADC in 10-lead MSOP — for precision data acquisition that needs both speed and DC accuracy: automatic test equipment, portable instruments and machine automation. ±1 LSB maximum INL with 100.5 dB SNR and -123 dB THD at 1 kHz, no latency or pipeline delay with first conversion accurate, and a high-Z input mode plus long acquisition phase that lets low-power precision amplifiers drive it directly — no dedicated high-speed ADC driver required. Input span compression runs the driver and ADC from common rails without a negative supply. Selection advice: the BRMZ code is the MSOP-10 version — for 16-bit at lower cost the AD4000 is the family sibling; the 1.8 V single supply with 1.71–5.5 V logic interface suits battery-powered field instruments. Daisy-chainable SPI simplifies multichannel layouts. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620ARZ is a low-power instrumentation amplifier from Analog Devices in an 8-pin SOIC package, with gain set by a single external resistor — for bridge sensors, strain gauges and other small differential signals. Its advantage is the classic three-op-amp instrumentation topology in one package: high common-mode rejection with minimal external circuitry, which shortens precision front-end design. Selection advice: the ARZ suffix denotes the standard grade in SOIC-8 on tape and reel — the AD620 also ships in DIP and higher grades, so match the full code to your footprint and accuracy requirements. Gain is set by one resistor value, so confirm your gain calculation against the datasheet formula during design. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD623ARZ-R7 is an Analog Devices single-supply instrumentation amplifier, rail-to-rail output, gain 1 to 1000 set by one external resistor, 800 kHz bandwidth at G=1, in SOIC-8 — the sensor front-end amplifier for bridges, thermocouples and low-level transducer signals. The single-resistor gain programming is the selection point: no matched resistor networks to source, with 0.10% gain accuracy at G=1, 200 µV max offset and 550 µA max supply current for battery-powered instruments. Selection advice: it runs on 3 to 12 V single supply or ±2.5 to ±6 V dual supply — but note the input range extends only 150 mV below ground on a single rail, so ground-referenced bipolar sensor signals still need the dual-supply configuration. The R7 suffix is the 7-inch reel (1000 pcs) packing of the SOIC-8. For higher precision or lower noise, compare the AD620/AD8221 family rather than assuming drop-in equivalence. Parameters verified against the ADI AD623 datasheet and Mouser/LCSC listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7124-8BBCPZ is an Analog Devices 24-bit sigma-delta ADC with 8 differential (15 pseudo-differential) inputs in 32-lead LFCSP — for multichannel precision measurement where board space and power both matter: PLC/DCS analog input modules, smart transmitters and portable instrumentation. Three user-selectable power modes trade throughput against noise (down to 255 µA with 24 nV rms at gain 128), the on-chip PGA offers gains 1 to 128 with rail-to-rail inputs, and the integrated 2.5 V reference plus dual excitation current sources cut external BOM for RTD and bridge sensors. Simultaneous 50/60 Hz rejection suits noisy industrial environments. Selection advice: the BBCPZ code is the 32-lead LFCSP tray version — for 4-channel designs the AD7124-4 is the pin-family sibling; the per-channel programmable digital filters let one hardware platform serve both fast and high-resolution channels. The on-chip diagnostics aid functional-safety designs. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD7190BRUZ is an Analog Devices 24-bit sigma-delta ADC with internal PGA in 24-lead TSSOP — the established weigh-scale and strain-gauge front end: the CN0102 reference design builds a complete precision weigh scale around it with only input filters added. Ultralow-noise performance from 4.7 Hz to 4.8 kHz output data rates covers both slow precision and faster hopper-scale applications, the internal PGA interfaces load cells directly, and the bridge power-down switch minimizes system power. On-chip temperature sensor and burnout detection complete the transducer interface. Selection advice: the BRUZ code is the TSSOP-24 tube version (-40 to +105 °C) — for 8-channel multiplexed weigh systems step up to the AD7124-8 on this site; the AD7190 stays the pick for dedicated single-bridge precision channels. Match the full BRUZ code for package and temperature grade. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8422BRZ is an Analog Devices rail-to-rail instrumentation amplifier in SOIC-8 — for bridge sensors, strain gauges and low-level differential signals where a discrete op-amp network drifts with temperature and layout. Gain is set by a single external resistor from 1 to 1000, with 25µV maximum input offset, 2.2MHz bandwidth and 150dB CMRR at high gain — precision front-end performance with minimal external circuitry. Selection advice: the BRZ code is the B grade (tighter offset than the A grade) in SOIC-8 tube packing — for reel packing specify the BRZ-R7; the MSOP-8 BRMZ suits tighter layouts. At 300µA supply current it fits battery-powered instruments, but confirm the 4.6V-to-36V supply span against your rails — for single 3.3V-only systems check the input range limits. For higher bandwidth or lower noise, compare the AD8421/AD8429 family rather than assuming interchangeability. Parameters verified against Analog Devices documentation and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8604DRUZ is an Analog Devices DigiTrim rail-to-rail quad operational amplifier — for precision single-supply signal conditioning: rail-to-rail input and output, very low offset voltage, single-supply operation, low input bias current, 14-lead TSSOP package. The rail-to-rail input and output maximize dynamic range on low single supplies, so sensor interfaces use the full ADC span without a negative rail; very low offset voltage keeps DC accuracy without trimming. Business impact: quad precision op amps are the workhorse of industrial and medical analog front ends — a PRODUCTION-status part with family-wide pin compatibility de-risks long-lifecycle designs. Selection advice: the DRUZ code is the 14-lead TSSOP — the AD8601, AD8602 and AD8604 are the single, dual and quad members of the family; for lower supply current consider the AD8605 family. Featured on hqbuy.com hot search (2026-09-28). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.