AWR2944ABGALTRQ1

ADS7846 is a Texas Instruments 4-wire resistive touch screen controller in 16-pin TSSOP — the industry-standard part behind two decades of PDAs, point-of-sale terminals and portable instruments: 2.2 V to 5.25 V operation, internal 2.5 V reference, direct battery measurement from 0 V to 6 V, on-chip temperature and touch-pressure measurement, SPI/QSPI 3-wire interface, auto power-down, under 0.75 mW typical at 2.7 V, 125 kHz throughput, -40 to +85 °C. The pin-compatible upgrade path is the selection point: it drops into ADS7843 sockets with only software changes, adding battery and temperature measurement the older part lacks — which is why it remains the default choice for resistive-touch retrofits and long-life industrial designs. Selection advice: for new designs needing 1.5 V digital I/O, the TSC2046 on this site is the pin-compatible successor; the TSSOP-16 is the standard package, with QFN-16 and VFBGA-48 for space-constrained boards. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AM2434BSDFHIALVR is a Texas Instruments Sitara AM243x high-performance MCU: up to four 800 MHz Arm Cortex-R5F cores, a 400 MHz Cortex-M4F, and dual gigabit PRU-ICSSG industrial-communication subsystems in a 441-ball FCBGA (17.2 x 17.2 mm). It is TI's consolidation play for factory automation — the R5F cluster delivers deterministic servo-loop control while the PRU-ICSSG runs full protocol stacks for EtherCAT target, PROFINET device and EtherNet/IP adapter on the same silicon, replacing architectures that needed an MCU plus an external industrial-Ethernet ASIC or FPGA. Heat evidence: the AM243x is TI's mainstream platform for servo drives and remote I/O modules, and its datasheet remains under active revision (Rev. J, 2026), signaling continued TI investment in the family. Selection advice: the full orderable encodes silicon revision, feature configuration, temperature grade and the ALV 441-ball FCBGA package on tape and reel — match it character-for-character; the ALX 293-ball FCCSP is a smaller, footprint-incompatible alternative, and R5F count plus PRU features vary across AM2431/32/34. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AM6232ATGGHIALWR is a Texas Instruments Sitara AM62x processor: dual 1.4 GHz Arm Cortex-A53 plus a Cortex-M4F in a 425-ball FCCSP (13 x 13 mm). The value proposition is Linux-class compute at microcontroller-class power — the A53 pair runs full Yocto/Debian HMI stacks while the M4F handles real-time I/O, so one device replaces an applications processor plus a companion MCU in industrial panels and gateways, and deep-sleep states in the milliwatt class simplify thermal and power design. TI's long-lifecycle industrial positioning protects multi-year programs from forced redesigns. Heat evidence: the AM62x family has been one of TI's most heavily promoted industrial platforms since its 2022 launch, with broad trade-press coverage and multiple third-party system-on-module vendors building AM62x-based products for HMI and edge AI. Selection advice: the ALW FCCSP-425 is the compact package variant — the AM625/AM623/AM620-Q1 family shares one TI product folder, so confirm the exact orderable against the datasheet because family members differ in feature set; the G temperature code and W carrier suffix must match your assembly flow. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CC1101RGP is a Texas Instruments sub-1 GHz RF transceiver in VQFN-20, tube packaging — for proprietary wireless sensor links in metering, alarms and remote control. The sub-1 GHz operation is the selection point: better wall penetration and range than 2.4 GHz at the same power budget. Selection advice: the RGP suffix denotes VQFN-20 in tube — for production volumes, the RGPT tape-and-reel variant feeds pick-and-place directly. This is a transceiver, not a protocol stack — plan firmware for your own packet format or a lightweight stack. Match the order code to your assembly process. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CC1101RGPR is a sub-1 GHz RF transceiver from Texas Instruments in a 20-pin VQFN package, designed for low-power wireless links in metering, sensor networks, remote controls and home automation. Its advantage is the sub-1 GHz band: longer range and better obstacle penetration than 2.4 GHz for the same power budget, which is why it remains a workhorse for long-life battery-powered nodes. Selection advice: RGP denotes the VQFN-20 package and the trailing R tape-and-reel packing — match the full CC1101RGPR code to your BOM, since the CC1101 family ships in several package and packing combinations. RF performance depends on the matching network and antenna design around the chip, so this part is a component choice, not a drop-in module; confirm your region frequency-plan requirements when you RFQ. We reconfirm code, lot and traceability before quotation and reply within 24 hours.

CC1101RGPT is a Texas Instruments sub-1 GHz RF transceiver in VQFN-20, tape and reel — for proprietary wireless sensor links in metering, alarms and remote control. The sub-1 GHz operation is the selection point: better wall penetration and range than 2.4 GHz at the same power budget. Selection advice: the RGPT suffix denotes VQFN-20 in tape and reel for production assembly — the tube-packed RGP variant suits prototypes and hand assembly. This is a transceiver, not a protocol stack — plan firmware for your own packet format or a lightweight stack. Match the order code to your assembly process. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CC1120RHBR is a Texas Instruments high-performance Sub-1 GHz RF transceiver in 32-pin VQFN, large reel — 164–192, 274–320, 410–480 and 820–960 MHz bands, 0–200 kbps, 2/4-FSK, GFSK, MSK and OOK modulation, −123 dBm sensitivity at 1.2 kbps (−127 dBm with coding gain), 2.0–3.6 V, SPI control, −40 °C to +85 °C. The narrowband blocking performance (91 dB at 10 MHz offset) is the selection point: in crowded 169/433/868/915 MHz ISM bands it holds a link where wider, cheaper radios get desensed — the reason for its use in metering, alarm and industrial telemetry. Selection advice: the R suffix is the 3000-piece large reel; CC1120RHBT is the 250-piece small reel for prototypes — same die, different reel. For +27 dBm output pair it with the CC1190 front end; for low-end short-range links the older CC1101 costs less but gives up selectivity. Match frequency band to your regional regulation (ETSI/FCC/ARIB). Evidence: the TI CC1120 datasheet and packaging addendum confirm the bands, data rates, VQFN-32 RHB package and reel options. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CC1352P74T0RGZR is a Texas Instruments SimpleLink dual-band wireless MCU — concurrent Sub-1 GHz and 2.4 GHz operation with integrated +20 dBm power amplifier, for grid infrastructure, smart meters and building automation: Thread, Zigbee, Bluetooth 5.2 LE, Wi-SUN, mioty, Amazon Sidewalk, 6LoWPAN and proprietary protocols via the Dynamic Multiprotocol Manager. Arm Cortex-M4F at 48 MHz with 704 KB Flash; 0.9 uA sleep with RTC and full RAM retention; sub-1 GHz bands from 287 MHz to 1315 MHz plus 2.4 GHz. Selection advice: the P7 is the high-power (+20 dBm) variant — for +10 dBm coin-cell designs the CC1352R7 costs less and draws less; the RGZR code is the 48-pin VQFN tape-and-reel orderable (-40 to +105C). For Wi-SUN smart-meter programs, TI's 15.4 stack is the reference implementation — confirm your stack certification requirements. Active per TI documentation. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CC2642R1FRGZT is a Texas Instruments Bluetooth Low Energy wireless microcontroller in VQFN-48, tape and reel — for connected sensor designs: beacons, wearables and smart-home nodes. The integrated BLE 5 radio plus Arm Cortex-M4F is the selection point: one chip handles both the wireless stack and the application, cutting BOM cost and board space. Selection advice: the RGZT suffix denotes VQFN-48 in tape and reel for production. Budget firmware effort for TI's BLE stack and RF matching — a pre-certified module (e.g., from our Wireless Modules category) is faster if you want to skip antenna tuning and certification. Match the order code to your assembly process. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CC2652R74T0RGZR is a Texas Instruments SimpleLink multiprotocol 2.4 GHz wireless MCU — Thread, Zigbee, Matter, Bluetooth 5.2 LE and proprietary 2.4 GHz on one die, for smart-home hubs, lighting and industrial sensor networks. 48 MHz Arm Cortex-M4F with 704 KB Flash and 152 KB RAM; direction-finding (AoA/AoD) for asset tracking; 0.9 uA standby with RTC; +5 dBm TX with temperature compensation. Selection advice: the R7 doubles the Flash of the older CC2652R (352 KB) — for Matter and Zigbee coordinator firmware the 704 KB is the safe choice; the RGZR code is the 48-pin VQFN tape-and-reel orderable (-40 to +105C). Against the CC1352P7 on this site, choose the CC2652R7 when you need only 2.4 GHz — the dual-band part costs more for sub-1 GHz you will not use. Active per TI documentation. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.