AH3711Q-SA-7

AH3711Q-P-B is a Diodes Incorporated automotive-qualified bipolar Hall-effect latch in a through-hole SIP-3 package, with a south-pole-on / north-pole-off output, a 3 V to 27 V operating range, and typical operate and release points of ±10 Gauss. The ±10 Gauss sensitivity is the selection point: it detects weaker magnetic fields than conventional latches, so designs can use smaller, lower-cost magnets and still keep magnetic margin, which cuts BOM cost and shrinks the sensing assembly in BLDC motor commutation, window powerlifts, sunroofs, tailgate drives, seat-adjustment motors, fans, pumps, and speed measurement. The business gain is automotive-grade robustness without added protection parts: a reverse-blocking diode and Zener clamp on the supply plus an overcurrent-limited open-drain output withstand 40 V load dumps, reverse polarity, and short circuits, while the chopper-stabilized design holds switch points stable across the -40°C to +150°C range with minimal drift from temperature and PCB assembly stress, backed by 8 kV HBM and 1 kV CDM ESD ratings. Evidence: the Diodes AH3711Q datasheet (DS47457 Rev. 1-2, October 2025) defines this P-B code as the SIP-3 (Bulk Pack) automotive variant in bulk packing, 1,000 pieces per pack, with marking code 3711Q, AEC-Q100 qualification, PPAP capability, and manufacture in IATF 16949 certified facilities. Selection advice: choose P-B for through-hole assembly, hand soldering, prototyping, or low-volume builds where no SMT line is available; note that bulk packing means manual insertion rather than reel-fed SMT, so for volume surface-mount production use the SA-7 (SOT23) or W-7 (SC59) tape-and-reel codes instead; this SIP-3 variant takes the south pole on the marked side, like the SOT23 variant, unlike the SC59 variant which takes it on the opposite side; choose the non-Q AH3711 only when automotive change control and PPAP are not required. Featured on Mouser New Products (2026-10-08). Parameters verified against Diodes Incorporated documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AH3711Q-W-7 is a Diodes Incorporated automotive-qualified bipolar Hall-effect latch in a SC59 package, with a south-pole-on / north-pole-off output, a 3 V to 27 V operating range, and typical operate and release points of ±10 Gauss. The ±10 Gauss sensitivity is the selection point: it detects weaker magnetic fields than conventional latches, so designs can use smaller, lower-cost magnets and still keep magnetic margin, which cuts BOM cost and shrinks the sensing assembly in BLDC motor commutation, window powerlifts, sunroofs, tailgate drives, seat-adjustment motors, fans, pumps, and speed measurement. The business gain is automotive-grade robustness without added protection parts: a reverse-blocking diode and Zener clamp on the supply plus an overcurrent-limited open-drain output withstand 40 V load dumps, reverse polarity, and short circuits, while the chopper-stabilized design holds switch points stable across the -40°C to +150°C range with minimal drift from temperature and PCB assembly stress, backed by 8 kV HBM and 1 kV CDM ESD ratings. Evidence: the Diodes AH3711Q datasheet (DS47457 Rev. 1-2, October 2025) defines this W-7 code as the SC59 automotive variant in 7-inch tape and reel, 3,000 pieces per reel, with marking code UTQ, AEC-Q100 qualification, PPAP capability, and manufacture in IATF 16949 certified facilities. Selection advice: choose W-7 only for layouts built for the SC59 land pattern, since SC59 and SOT23 footprints are not interchangeable; critically, this SC59 variant takes the south pole on the opposite side, while the SOT23 (SA-7) and SIP-3 (P-B) variants take it on the marked side, so the magnet orientation must be flipped when switching packages or the latch will not operate; choose the SIP-3 P-B code for through-hole or hand assembly; choose the non-Q AH3711 only when automotive change control and PPAP are not required. Featured on Mouser New Products (2026-10-08). Parameters verified against Diodes Incorporated documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AH4931Q-W6-7 is a Diodes Incorporated automotive-qualified 3D Hall-effect sensor — for contactless position and direction sensing: three-axis magnetic field detection, Q-suffix automotive qualification, SOT-26 (Type CJ) package. A single 3D Hall IC replaces multiple single-axis sensors plus the mechanical linkages they need — contactless sensing eliminates wear in knobs, pedals and gear selectors; the automotive Q grade meets AEC-Q100 change-control requirements for in-cabin and under-hood designs. Business impact: 3D Hall sensors consolidate position-sensing BOMs — one qualified part instead of two or three discretes with alignment fixtures. Selection advice: the Q-W6-7 code is the automotive SOT-26 variant in tape-and-reel — for standard grade consider the AH4931; verify the magnetic operating points (Bop/Brp) against the actuator magnet in the Diodes datasheet. Featured on Mouser New Products (2026-10-13). Parameters verified against Diodes Incorporated documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS37002LMABTR-050B5 is an isolated Hall-effect current sensor from Allegro MicroSystems in a 16-pin SOIC package, with a 50 A measurement range on tape and reel — for high-current motor drives, solar inverters and industrial power. The 50 A range in a standard SOIC-16 is the selection point: high-current isolated sensing without a bulky module or external shunt. Selection advice: the 050B5 code denotes the 50 A bidirectional variant — the ACS37002 ships in multiple ranges that are not interchangeable, so match the full ACS37002LMABTR-050B5 code. Confirm your current range, bandwidth and isolation requirements against the datasheet. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS712ELCTR-05B-T is an isolated Hall-effect current sensor from Allegro MicroSystems in an 8-pin SOIC package, with a 5 A measurement range — for motor control, power supplies and overcurrent protection. The integrated Hall sensor with 2.1 kV isolation is the selection point: current sensing with galvanic isolation and no shunt resistor, so no power dissipation or high-side measurement headaches. Selection advice: the 05B code denotes the ±5 A range — the ACS712 ships in 5/20/30 A variants with different sensitivities that are not interchangeable, so match the full ACS712ELCTR-05B-T code. Confirm your current range and bandwidth needs against the datasheet. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS712ELCTR-20A-T is an Allegro MicroSystems fully integrated Hall-effect linear current sensor in 8-pin SOIC (0.154 in narrow), tape-and-reel packing (TR) — ±20 A sensing range, 100 mV/A output sensitivity, ratiometric voltage output centered at 2.5 V, 5 µs output rise time, 80 kHz typical bandwidth, 4.5–5.5 V single supply, ±1.5% total output error at 25 °C, 1.2 mΩ primary conductor resistance, 2.1 kV RMS isolation between pins 1–4 and 5–8, −40 to +85 °C. The integrated copper conduction path is the selection point: current flows through the package itself, so sensing adds only 1.2 mΩ of series resistance — no external high-power shunt resistor and no isolation optocoupler needed for 2.1 kV RMS separation in motor control, SMPS, load monitoring and overcurrent protection. Selection advice: this is the bidirectional 20 A member — the ±5 A and ±30 A siblings differ in sensitivity and bandwidth, and the 20 A choice trades resolution against range, so match the range to your actual fault-current envelope. Allegro notes the ACS712 is not intended for automotive applications. Evidence: Allegro ACS712 datasheet and distributor listings confirm ±20 A, 100 mV/A, 80 kHz, 2.1 kV RMS, 8-SOIC and tape-and-reel packing. Match the full ACS712ELCTR-20A-T code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS712ELCTR-30A-T is an Allegro Hall-effect linear current sensor in 8-SOIC — ±30 A bidirectional sensing, 66 mV/A sensitivity, 5 µs output response time, 80 kHz bandwidth, ±1.5% accuracy, 2.1 kVRMS galvanic isolation between the current path and the output, 1.2 mΩ internal conductor, 5 V single supply, ratiometric analog voltage output, tape-and-reel packing (T), -40 to +85 °C. The zero-insertion-loss sensing is the selection point: no external shunt resistor and no power dissipated in the sense path — the current flows through a 1.2 mΩ copper path while the output voltage is proportional to AC or DC current. Selection advice: this is the ±30 A version — the ACS712 also comes in 5 A and 20 A versions with different sensitivity, so match the full ACS712ELCTR-30A-T code to your current range. The FILTER pin lets you set bandwidth with an external capacitor. Evidence: Allegro ACS712 datasheet and distributor listings confirm ±30 A, 66 mV/A, 5 µs, 8-SOIC and reel packing. Match the full ACS712ELCTR-30A-T code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADP5200 is a Panasonic PS-A series compound pressure sensor in 6-pin SMD module — ±100 kPa rated pressure (±200 kPa proof), amplified 0 V to 4.5 V analog output, ±1.25 %FS accuracy, temperature compensated, 5 V drive, -10 °C to +60 °C. The amplified temperature-compensated output is the selection point: it drops straight into a microcontroller ADC with no external instrumentation amplifier or calibration network. Selection advice: ADP5200 is the ±100 kPa SMD code — the ADP5100 is the DIP twin and the ADP5240 covers 100 kPa gauge; match the pressure type (compound vs gauge) to your medium. Honest lifecycle note: this series is in Last Time Buy — available for existing designs, so confirm the lot and consider a lifetime buy for ongoing production. Evidence: the Panasonic PS-A official catalog confirms the pressure range and package codes. State quantity and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADXL345BCCZ is a digital three-axis accelerometer from Analog Devices in a 14-pin LGA package — for motion detection, tilt sensing, tap/double-tap input and free-fall detection in handheld, wearable and industrial devices. Its advantage is the built-in activity/inactivity and tap sensing: motion events wake the host from sleep without continuous polling, which cuts system power in battery designs. Selection advice: the CCZ suffix denotes the LGA-14 package on tape and reel — the ADXL345 ships in several packages, so match the full code to your layout. For new designs, compare against current-generation accelerometers on power and noise if your budget allows; for existing designs, match the code exactly. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADXL345BCCZ-RL is a 3-axis digital accelerometer from Analog Devices in production status, in a 14-lead LGA package with selectable ±2/±4/±8/±16 g ranges and SPI/I2C digital output on tape and reel — for motion sensing, tilt detection and activity monitoring. The selectable g-range with digital output is the selection point: one part covers both high-sensitivity tilt and high-g shock detection, which is why the ADXL345 became the reference hobbyist accelerometer. Selection advice: the BCCZ-RL suffix denotes the LGA-14 package on tape and reel — match the full ADXL345BCCZ-RL code. Confirm your range and interface against the datasheet. Parameters verified against the Analog Devices official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.