AD8610AR

AD8606ARZ is a dual rail-to-rail precision operational amplifier from Analog Devices in an 8-pin SOIC package — for low-voltage precision systems, data acquisition front ends and medical instrumentation. The combination of precision DC specs with rail-to-rail operation is the selection point: it brings precision-grade offset and drift to single-supply low-voltage designs that older precision op-amps cannot serve. Selection advice: the ARZ suffix denotes SOIC-8 on tape and reel — match the full AD8606ARZ code to your footprint and packing needs. Confirm your offset, drift and noise requirements against the datasheet before substituting for a general-purpose op-amp. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADA4077-2ARZ is an Analog Devices dual precision operational amplifier in 8-lead SOIC, tube packing — 15 µV typical input offset (50 µV max A-grade), 0.25 µV/°C drift, 3.6 MHz gain-bandwidth, 1.2 V/µs slew rate, 1 nA input bias and 400 µA per channel, specified over −40 °C to +125 °C on 5 V to 30 V supplies (±2.5 V to ±15 V). Unity-gain stable with no phase reversal and stable into 1000 pF capacitive loads. The offset-plus-drift combination is the selection point: thermocouple, RTD and strain-gauge front ends hold calibration across temperature without trimming, which is the whole value proposition of a precision op amp. Selection advice: the ARZ code is the tube version — ARZ-R7/ARZ-RL is the same die on tape and reel for pick-and-place; this is not a rail-to-rail output part, so size your signal swing inside the ±15 V rails. For single-channel or quad layouts use the ADA4077-1/ADA4077-4. Evidence: LCSC and element14/Newark listings confirm 15 µV, 3.6 MHz, −40 to +125 °C, SOIC-8 and wide distributor stock. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8605ARTZ-REEL7 is an Analog Devices precision single-channel CMOS operational amplifier — rail-to-rail input and output, 10 MHz gain-bandwidth product, 5 V/µs slew rate — with 20 µV typical / 80 µV maximum offset voltage, 0.2 pA input bias current and 8 nV/√Hz voltage noise, on a single 2.7 to 5.5 V supply, in SOT-23-5, operating -40 to +125 °C. ADI DigiTrim technology is the selection point: laser-trim-grade offset without laser trimming, so microvolt precision holds across production lots for sensor front ends, photodiode amplifiers, active filters and audio stages. Selection advice: the femtoamp-class bias current suits high-impedance sources that would be loaded by bipolar op amps — photodiodes, piezoelectric and electret sensors — but confirm your supply rail is within 5.5 V and that one channel is enough, since the dual AD8606 and quad AD8608 cover multi-channel designs in the same family. The REEL7 suffix is the 7-inch reel (3000 pieces) — match the full code if your line needs a different reel size or tube packing. This is a general-purpose precision part, not automotive qualified. Evidence: ADI datasheet and distributor listings confirm 10 MHz, 5 V/µs, 80 µV max offset, 0.2 pA bias and SOT-23-5. Confirm lead time and availability at RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

Analog Devices AD8672ARMZ is a dual precision operational amplifier in an 8-lead MSOP package. Its 2.8 nV/rtHz voltage noise and 75 uV max offset voltage (datasheet Rev. F) give you quiet, accurate front ends for instrumentation, PLL filters, GPS filters and sensor conditioning, so small DC and low-level signals stay clean without extra filtering stages. The 10 MHz gain-bandwidth, 3 mA per amplifier supply current, +-5 V to +-15 V dual-supply range and no-phase-reversal, unity-gain-stable behavior simplify reuse across product variants and cut design risk, protecting margins on repeat builds. Selection advice: the same datasheet covers the single AD8671 and quad AD8674, so match the channel count to your board instead of wiring unused channels, and use the AD8672-EP enhanced product only if you need the -55 C to +125 C defense flow. Featured on hqew.com yesterday-hot list (2026-10-13). Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

OP07CDR is a Texas Instruments precision operational amplifier in SOIC-8 — for DC measurement front-ends: bridge amplifiers, thermocouple conditioning and precision integrators. 150 µV maximum input offset (C-grade), ±14 nA maximum bias current, 600 kHz gain-bandwidth, ±3 V to ±18 V supply, near-zero offset drift. Heat evidence: precision analog remains on firm allocation as instrumentation and industrial demand holds — the OP07 is the classic precision bipolar op-amp with decades of continuous production. Selection advice: the CDR suffix is SOIC-8 on reel for SMT — same die as the DIP OP07CP; note the older OP07CD (tube) is obsolete, always order the R (reel) variant for current production. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

OPA2188AID is a Texas Instruments zero-drift dual operational amplifier in 8-pin SOIC — for precision signal chains where offset drift destroys accuracy over temperature: bridge sensors, thermocouple front ends and precision current sensing. 25 µV maximum offset voltage with 0.03 µV/°C drift, 8.8 nV/√Hz noise, 2 MHz gain bandwidth, rail-to-rail output, on 4 V to 36 V supplies at 475 µA maximum per channel. The auto-zero architecture is the selection point: offset and drift an order of magnitude better than standard bipolar op-amps, with no 1/f noise corner to corrupt slow measurements. Selection advice: this is the precision step up from the LM358 on this site — specify the OPA2188 when the error budget cannot tolerate millivolt offsets; for cost-driven non-precision use the LM358 remains the economical choice. The AID code is the tube SOIC — AIDR is the reel. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD620ARZ is a low-power instrumentation amplifier from Analog Devices in an 8-pin SOIC package, with gain set by a single external resistor — for bridge sensors, strain gauges and other small differential signals. Its advantage is the classic three-op-amp instrumentation topology in one package: high common-mode rejection with minimal external circuitry, which shortens precision front-end design. Selection advice: the ARZ suffix denotes the standard grade in SOIC-8 on tape and reel — the AD620 also ships in DIP and higher grades, so match the full code to your footprint and accuracy requirements. Gain is set by one resistor value, so confirm your gain calculation against the datasheet formula during design. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD623ARZ-R7 is an Analog Devices single-supply instrumentation amplifier, rail-to-rail output, gain 1 to 1000 set by one external resistor, 800 kHz bandwidth at G=1, in SOIC-8 — the sensor front-end amplifier for bridges, thermocouples and low-level transducer signals. The single-resistor gain programming is the selection point: no matched resistor networks to source, with 0.10% gain accuracy at G=1, 200 µV max offset and 550 µA max supply current for battery-powered instruments. Selection advice: it runs on 3 to 12 V single supply or ±2.5 to ±6 V dual supply — but note the input range extends only 150 mV below ground on a single rail, so ground-referenced bipolar sensor signals still need the dual-supply configuration. The R7 suffix is the 7-inch reel (1000 pcs) packing of the SOIC-8. For higher precision or lower noise, compare the AD620/AD8221 family rather than assuming drop-in equivalence. Parameters verified against the ADI AD623 datasheet and Mouser/LCSC listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

AD8422BRZ is an Analog Devices rail-to-rail instrumentation amplifier in SOIC-8 — for bridge sensors, strain gauges and low-level differential signals where a discrete op-amp network drifts with temperature and layout. Gain is set by a single external resistor from 1 to 1000, with 25µV maximum input offset, 2.2MHz bandwidth and 150dB CMRR at high gain — precision front-end performance with minimal external circuitry. Selection advice: the BRZ code is the B grade (tighter offset than the A grade) in SOIC-8 tube packing — for reel packing specify the BRZ-R7; the MSOP-8 BRMZ suits tighter layouts. At 300µA supply current it fits battery-powered instruments, but confirm the 4.6V-to-36V supply span against your rails — for single 3.3V-only systems check the input range limits. For higher bandwidth or lower noise, compare the AD8421/AD8429 family rather than assuming interchangeability. Parameters verified against Analog Devices documentation and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADUM7801-8BRIZ is an Analog Devices 25 MHz isolated ADC with sigma-delta modulated bit-stream output in 8-lead wide-body SOIC, for shunt current sensing in motor drives, solar inverters, and power converters. It delivers 16 bits with no missing codes over a +/-320 mV full-scale input, 88 dB typical SNR, and 5700 V rms isolation with 200 kV per us minimum common-mode transient immunity, so the controller side stays protected from noisy high-voltage power stages. The benefit is replacing an ADC plus optocoupler pair with one isolated part: the digital output crosses the barrier directly, cutting board area and preserving accuracy in high-dV/dt environments. Selection advice: the output is a pulse-density bit stream, not a parallel word, so your controller or FPGA must implement a sinc3 decimation filter; match the clock rate to your bandwidth and SNR target per the datasheet. The 8BRIZ code is the tube-packed wide-body SOIC version; for reel packing order the -RL code. Listed in DigiKey New Product Arrivals. Parameters verified against Analog Devices documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.