ICM-20948

MPU-9250 is a TDK InvenSense 9-axis MEMS motion-tracking device in QFN-24 (3.0 x 3.0 x 1.0 mm) — a multi-chip module combining a 3-axis gyroscope (±250/500/1000/2000 °/s) and 3-axis accelerometer (±2/4/8/16 g) die with an AK8963 3-axis magnetometer (±4800 µT), an on-chip Digital Motion Processor (DMP), dedicated auxiliary I2C sensor bus, I2C up to 400 kHz and SPI interfaces, VDD 2.4–3.6 V with VLOGIC 1.71 V to VDD, −40 to +85 °C. The single-package 9-axis integration is the selection point: accel plus gyro plus compass plus DMP in a 3 x 3 mm footprint, which is why this part powered the drone and wearable generation that needed orientation output from one chip. Selection advice: TDK lists MPU-9250 as Obsolete and recommends the ICM-20948 as the alternate — TDK own migration note stresses it is a superset/subset hardware change and not code-compatible, so treat any MPU-9250 offer as end-of-life stock with date-code traceability and plan new designs on the ICM-20948 register set instead of assuming register-level compatibility. Evidence: TDK/InvenSense MPU-9250 product specification (Rev. 1.1) and distributor listings confirm the 9-axis ranges, AK8963 compass, QFN-24 and obsolete status. Match the full MPU-9250 code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

MPU-6050 is a TDK InvenSense 6-axis MEMS motion-tracking device in QFN-24 (4.0 x 4.0 x 0.9 mm) — 3-axis gyroscope (±250/500/1000/2000 °/s) plus 3-axis accelerometer (±2/4/8/16 g) with 16-bit ADCs, an on-chip Digital Motion Processor (DMP) engine, 1024-byte FIFO, digital temperature sensor, 10,000 g shock tolerance and an auxiliary master I2C bus for external magnetometers, VDD 2.375–3.46 V with a separate VLOGIC pin setting the I2C interface levels (1.71 V to VDD). The DMP plus FIFO is the selection point: motion-fusion, gesture and timing work runs on-chip while the host sleeps, which is why this part defined the Arduino/drone gimbal era of low-cost IMUs. Selection advice: the MPU-6050 supports I2C only — if you need SPI, the MPU-6000 is the pin-compatible twin with SPI plus a single supply pin; do not treat them as code-identical. TDK lists MPU-6050 as Obsolete — production has stopped and final shipment is complete, so treat any offer as end-of-life stock: require date-code traceability and, for new designs, evaluate the current TDK IMU family instead. Evidence: InvenSense MPU-6000/MPU-6050 product specification (Rev. 3.4) and TDK product pages confirm the ranges, VDD, VLOGIC, QFN-24 and obsolete status. Match the full MPU-6050 code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ICM-42670-P is a TDK InvenSense 6-axis MotionTracking IMU combining 3-axis gyroscope and 3-axis accelerometer in 2.5x3 mm LGA-14 — for high-performance motion sensing in industrial robotics, AR/VR headsets and gaming controllers. 16-bit resolution, ±2/4/8/16 g accelerometer ranges, I3C/I2C/SPI interfaces, 550 µA operating current, and -40 to +85°C range. Ranked #16 on the 创芯指数 March 2026 hot-search TOP 50 with 22,506 searches and a 222.90% month-on-month increase, as IMU demand extends from consumer into robotics and drones. Selection advice: the -P code is the standard LGA-14 package — at 0.55 mA in low-noise mode it undercuts the ICM-42688-P (0.88 mA) for battery-powered designs; the I3C interface suits new sensor hubs while I2C keeps legacy compatibility. Parameters verified against TDK InvenSense documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ICM-42688-P is a low-noise 6-axis gyroscope and accelerometer from TDK InvenSense in an LGA-14 package — for drones, robotics, wearables and image stabilization. The low-noise 6-axis IMU with on-chip sensor fusion support is the selection point: it delivers stable orientation output for motion tracking without a separate co-processor. Selection advice: confirm your full-scale range and output data rate requirements against the datasheet — the P variant targets high-performance applications versus cost-optimized IMUs. Verify your interface (I2C/SPI) and power budget. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS37002LMABTR-050B5 is an isolated Hall-effect current sensor from Allegro MicroSystems in a 16-pin SOIC package, with a 50 A measurement range on tape and reel — for high-current motor drives, solar inverters and industrial power. The 50 A range in a standard SOIC-16 is the selection point: high-current isolated sensing without a bulky module or external shunt. Selection advice: the 050B5 code denotes the 50 A bidirectional variant — the ACS37002 ships in multiple ranges that are not interchangeable, so match the full ACS37002LMABTR-050B5 code. Confirm your current range, bandwidth and isolation requirements against the datasheet. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS712ELCTR-05B-T is an isolated Hall-effect current sensor from Allegro MicroSystems in an 8-pin SOIC package, with a 5 A measurement range — for motor control, power supplies and overcurrent protection. The integrated Hall sensor with 2.1 kV isolation is the selection point: current sensing with galvanic isolation and no shunt resistor, so no power dissipation or high-side measurement headaches. Selection advice: the 05B code denotes the ±5 A range — the ACS712 ships in 5/20/30 A variants with different sensitivities that are not interchangeable, so match the full ACS712ELCTR-05B-T code. Confirm your current range and bandwidth needs against the datasheet. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS712ELCTR-20A-T is an Allegro MicroSystems fully integrated Hall-effect linear current sensor in 8-pin SOIC (0.154 in narrow), tape-and-reel packing (TR) — ±20 A sensing range, 100 mV/A output sensitivity, ratiometric voltage output centered at 2.5 V, 5 µs output rise time, 80 kHz typical bandwidth, 4.5–5.5 V single supply, ±1.5% total output error at 25 °C, 1.2 mΩ primary conductor resistance, 2.1 kV RMS isolation between pins 1–4 and 5–8, −40 to +85 °C. The integrated copper conduction path is the selection point: current flows through the package itself, so sensing adds only 1.2 mΩ of series resistance — no external high-power shunt resistor and no isolation optocoupler needed for 2.1 kV RMS separation in motor control, SMPS, load monitoring and overcurrent protection. Selection advice: this is the bidirectional 20 A member — the ±5 A and ±30 A siblings differ in sensitivity and bandwidth, and the 20 A choice trades resolution against range, so match the range to your actual fault-current envelope. Allegro notes the ACS712 is not intended for automotive applications. Evidence: Allegro ACS712 datasheet and distributor listings confirm ±20 A, 100 mV/A, 80 kHz, 2.1 kV RMS, 8-SOIC and tape-and-reel packing. Match the full ACS712ELCTR-20A-T code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ACS712ELCTR-30A-T is an Allegro Hall-effect linear current sensor in 8-SOIC — ±30 A bidirectional sensing, 66 mV/A sensitivity, 5 µs output response time, 80 kHz bandwidth, ±1.5% accuracy, 2.1 kVRMS galvanic isolation between the current path and the output, 1.2 mΩ internal conductor, 5 V single supply, ratiometric analog voltage output, tape-and-reel packing (T), -40 to +85 °C. The zero-insertion-loss sensing is the selection point: no external shunt resistor and no power dissipated in the sense path — the current flows through a 1.2 mΩ copper path while the output voltage is proportional to AC or DC current. Selection advice: this is the ±30 A version — the ACS712 also comes in 5 A and 20 A versions with different sensitivity, so match the full ACS712ELCTR-30A-T code to your current range. The FILTER pin lets you set bandwidth with an external capacitor. Evidence: Allegro ACS712 datasheet and distributor listings confirm ±30 A, 66 mV/A, 5 µs, 8-SOIC and reel packing. Match the full ACS712ELCTR-30A-T code. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADP5200 is a Panasonic PS-A series compound pressure sensor in 6-pin SMD module — ±100 kPa rated pressure (±200 kPa proof), amplified 0 V to 4.5 V analog output, ±1.25 %FS accuracy, temperature compensated, 5 V drive, -10 °C to +60 °C. The amplified temperature-compensated output is the selection point: it drops straight into a microcontroller ADC with no external instrumentation amplifier or calibration network. Selection advice: ADP5200 is the ±100 kPa SMD code — the ADP5100 is the DIP twin and the ADP5240 covers 100 kPa gauge; match the pressure type (compound vs gauge) to your medium. Honest lifecycle note: this series is in Last Time Buy — available for existing designs, so confirm the lot and consider a lifetime buy for ongoing production. Evidence: the Panasonic PS-A official catalog confirms the pressure range and package codes. State quantity and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

ADXL345BCCZ is a digital three-axis accelerometer from Analog Devices in a 14-pin LGA package — for motion detection, tilt sensing, tap/double-tap input and free-fall detection in handheld, wearable and industrial devices. Its advantage is the built-in activity/inactivity and tap sensing: motion events wake the host from sleep without continuous polling, which cuts system power in battery designs. Selection advice: the CCZ suffix denotes the LGA-14 package on tape and reel — the ADXL345 ships in several packages, so match the full code to your layout. For new designs, compare against current-generation accelerometers on power and noise if your budget allows; for existing designs, match the code exactly. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.