DRV8833PWR

DRV8833RTYR is a Texas Instruments DRV8833 dual H-bridge motor driver in the 16-pin WQFN package — 2.7 to 10.8 V supply, 1.5 A RMS / 2 A peak per H-bridge (with proper PCB thermal design), drives two DC motors or one bipolar stepper, tape-and-reel packing of 3000 (RTYR; RTYT is the small reel), -40 to +85 °C. The thermally enhanced WQFN with PowerPAD is the selection point: full 1.5 A RMS in a 4 × 4 mm footprint, versus only 500 mA RMS in the standard TSSOP-16 (PWR) variant. Selection advice: match the package to your current — 1.5 A needs this RTY (or the HTSSOP PWP) variant; for light loads the cheaper PWR suffices. Built-in PWM winding-current regulation sets motor current with a sense resistor, and paralleling both bridges delivers 3 A RMS to a single motor. Sleep mode and the fault output (overcurrent, thermal, undervoltage) protect battery-powered designs. Evidence: TI DRV8833 datasheet (SLVSAR1E) and TI pack addendum confirm 2.7-10.8 V, 1.5 A RMS in RTY, WQFN-16 and 3000-reel packing. Match the full DRV8833RTYR code for package and packing. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

F: 3.0-A standalone switch-mode buck charger with NVDC power path for single-cell Li-Ion/Li-polymer, 3.9-13.5-V input, 19.5-mohm BATFET, 9.5-uA battery leakage, WQFN-24. A: Full FET integration and hardware-configurable JEITA profile deliver fast charging without host firmware management. B: Shorter firmware development and faster time-to-market for portable devices. E: Ranked on hqbuy.com real-time hot list (2026-10-14). Selection advice: pick BQ25616 over the I2C siblings BQ25618/BQ25619 when the host MCU should not own charging registers; note this RTWR orderable is the WQFN-24 tape-and-reel option. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

BQ25790 is Texas Instruments’ 5-A buck-boost battery charger for 1-to-4-cell Li-ion/Li-polymer packs in 2.9x3.3mm WCSP-56 — for USB-C PD charging where input voltage swings both above and below the battery voltage: the integrated buck-boost stage (all four switching FETs plus battery FET on-chip) automatically transitions between buck, boost and buck-boost without host intervention. 97% charging efficiency at 30 W, 3.6-to-24 V input range, NVDC power-path management that keeps the system alive even with a dead or removed battery, dual-input selector (USB, barrel, wireless, solar), D+/D- handshake for legacy fast-charge adapters, and I2C host control with an integrated ADC for telemetry. USB-C/PD compatible, -40 to +85°C. Selection advice: the WCSP package is the smallest footprint option — for easier assembly specify the QFN sibling BQ25792; for solar-input designs the BQ25798 variant adds MPPT. State cell count and input source mix in the RFQ so the offered lot is matched to the right charge profile. Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

BQ4050RSMR is a Texas Instruments battery fuel gauge — for 1-series Li-ion and Li-polymer packs: Impedance Track gauging algorithm for accurate state-of-charge reporting, integrated protection-friendly architecture, VQFN-12 package. The Impedance Track algorithm learns the cell characteristics over cycles, so reported capacity stays accurate as the battery ages — unlike simple coulomb counters that drift; accurate gauging prevents both unexpected shutdowns and over-conservative capacity margins. Business impact: reliable fuel gauging is a safety and user-experience feature — medical, industrial and consumer devices all depend on trustworthy remaining-capacity readings. Selection advice: the RSMR code denotes VQFN-12 on tape and reel — the BQ4050 targets single-cell packs — for multi-cell designs look at the BQ40 family stackable gauges; cell characterization data improves initial accuracy. Ranked #15 on the hqbuy.com real-time hot list (2026-10-05). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

CSD95410RRB is a Texas Instruments 90 A peak NexFET smart power stage — for multiphase buck converters powering AI accelerators, FPGAs and datacenter ASICs: driver plus power MOSFETs in a 5x6 mm 41-pin VQFN-CLIP package, -40°C to +125°C. Integrated temperature-compensated bidirectional current sense and analog temperature output feed the controller's telemetry loop, while 1.75 MHz switching and ultra-low-inductance packaging push power density. This is the ACTIVE successor to the NRND CSD95490 — same footprint class, higher current rating. Selection advice: pair with TI multiphase controllers (TPS53681/TPS53688 on this site) per TI reference designs; the industry-common 5x6 mm footprint allows second-sourcing across vendors, but verify current-sense calibration against your controller. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DRV8256PPWPR is a Texas Instruments single H-bridge motor driver with integrated current sense and smart-tune technology — for industrial brushed-DC drives: 4.5-V to 48-V supply, 6.4-A peak output, 165-mΩ RDS(ON), and an internal current-mirror sense architecture that removes the power shunt resistor. The selection point is the inrush control: the driver regulates motor startup current automatically, protecting 24-V and 48-V rails from stall-current collapse — plus spread-spectrum clocking for low EMI in noise-sensitive cabinets. Selection advice: the PPWPR suffix is the HTSSOP-28 tape-and-reel orderable — the E variant (DRV8256EPWPR) uses EN/IN control while the P variant uses PH/EN, so match the control interface to your MCU firmware; for the compact 4x4-mm VQFN specify the RGER variant. TI lists this as Active in production. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DRV8350 is a Texas Instruments 102-V max 3-phase smart gate driver — for BLDC motor drives in drones, robotics, e-bikes, power tools and factory automation: 9-V to 100-V triple half-bridge driver with smart gate drive architecture, adjustable slew rate for EMI control, and VGS handshake plus minimum dead-time insertion to prevent shoot-through. The selection point is the integration: optional triple low-side current shunt amplifiers and an integrated buck regulator (LM5008A-based, 6-V to 95-V in, 350-mA out) collapse the gate-drive power tree onto one chip. Selection advice: the hardware-interface variant suits cost-sensitive designs, while the SPI variant adds fault reporting and configurability — for 65-V systems the DRV8320 is the lower-voltage sibling; pair with TI NexFET power stages per the DRV8350H-EVM reference. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DRV8701ERGER is a Texas Instruments 47-V H-bridge smart gate driver for brushed-DC motors with external MOSFETs — for 12-V to 24-V bidirectional drives in robotics, power tools and industrial automation: 5.9-V to 45-V supply, drives four external N-channel MOSFETs, and integrates a 20-V/V current shunt amplifier plus fixed off-time PWM current regulation. The selection point over integrated drivers is scalability: pick your own FETs for 10-A, 30-A or higher designs, with 5-level adjustable gate drive (6-mA to 150-mA source) to tame EMI on large FETs. Selection advice: the ERGER suffix is the 4x4-mm VQFN-24 tape-and-reel orderable with PH/EN control — for PWM control specify the DRV8701PRGER instead; the two on-chip LDOs (4.8-V AVDD, 3.3-V DVDD) can power your MCU, collapsing the aux supply. TI lists this as Active in production. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DRV8825 is a Texas Instruments 45-V, 2.5-A bipolar stepper motor driver with integrated microstepping indexer — for printers, 3D printers, CNC machines, robotics and factory automation: 8.2-V to 45-V supply, up to 1/32 microstepping, simple STEP/DIR interface, and multiple decay modes (mixed, slow, fast) for smooth quiet motion. The selection point is the on-chip indexer: no external microstepping lookup tables needed, and the 400-mΩ RDS(ON) keeps conduction losses low at 1.5-A RMS without a heatsink. Selection advice: the DRV8825 is the higher-current drop-in upgrade path from the A4988 carrier footprint — for new designs needing integrated current sensing and 1/256 microstepping, the DRV8424 family is the newer alternative; for lower current the pin-compatible DRV8824 covers 1.6 A. TI lists factory automation and robotics as target applications. Parameters verified against TI documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DRV8825PWPR is a Texas Instruments microstepping bipolar stepper motor driver in HTSSOP-28 PowerPAD, tape and reel — for 3D printers, scanners and office automation driving one bipolar stepper with smooth, quiet motion. 8.2 V to 45 V supply with up to 2.5 A per coil and 1/32 microstepping is the selection point: high-voltage headroom plus fine microstepping from a simple STEP/DIR interface. Selection advice: the PWP suffix denotes the thermally enhanced HTSSOP-28 — solder the exposed pad to copper, because 2.5 A is only reachable with proper heatsinking; R denotes tape and reel. Against the Allegro A4988 on this site (35 V, 2 A, 1/16 step): pick the DRV8825 for higher voltage, higher current and finer microstepping; pick the A4988 for lower cost at modest power. Built-in overcurrent, thermal shutdown and undervoltage lockout plus the nFAULT pin simplify fault handling. TI lists this part as Active. Parameters verified against the TI official product page. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

DRV8833PWR is listed on the L298N alternatives page as a functional candidate (registry model DRV8833). Review that page’s checklist before substituting.