PRTR5V0U2X

PESD3V3S1UB is a Nexperia unidirectional ESD protection diode in SOD-523 — for single-line ESD defense on 3.3 V rails: SIM cards, sensor lines and low-voltage logic. 30 kV ESD rating with 20 V maximum clamping in a 1.6 x 0.8 mm package is the selection point: protection that fits where SOD-323 will not. Selection advice: unidirectional suits lines with defined polarity — for bipolar or AC-coupled lines, the bidirectional PESD5V0S1BA on this site is the correct pick; note its 207 pF capacitance is higher than the 5V0S1BA 45 pF, so avoid it on high-speed differential pairs. The ,115 suffix denotes tape and reel. −65 °C to +150 °C. Nexperia lists this part as Active through distribution. Parameters verified against the Nexperia datasheet and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

PESD5V0S1BA is a Nexperia bidirectional ESD protection diode in SOD-323 — for single-line ESD defense on 5 V interfaces: USB, HDMI control lines and keypads. 30 kV ESD rating with 14 V clamping and 45 pF capacitance is the selection point: it survives direct ESD strikes while staying small enough for one signal line. Selection advice: this is the bidirectional, 5 V, low-capacitance member of the pair — against the PESD3V3S1UB on this site (unidirectional, 3.3 V, 207 pF in smaller SOD-523), choose the 5V0S1BA for 5 V rails and faster edges where capacitance matters, the 3V3S1UB where the rail is 3.3 V and the line has defined polarity. The ,115 suffix denotes tape and reel. 130 W peak pulse power, −65 °C to +150 °C. Nexperia lists this part as Active through distribution; the -QF suffix (not this part) is the AEC-Q101 variant. Parameters verified against the Nexperia datasheet and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

TPD4E1B06DRLR is a Texas Instruments 4-channel bidirectional ESD protection diode array - for hardening high-speed interfaces against system-level ESD: IEC 61000-4-2 contact discharge plus-minus 12kV and air-gap discharge plus-minus 15kV, IEC 61000-4-5 surge 3.0A (8/20us), 0.5nA maximum leakage current, 0.7pF typical I/O capacitance, SOT-5X3 (DRL) 6-pin package, -40C to 125C industrial range. The 0.7pF line capacitance keeps signal integrity intact on USB2.0, Ethernet, SATA and LVDS lanes where bulkier TVS parts would close the eye, so protection can sit directly on the connector without a layout penalty; the 0.5nA leakage preserves precision analog measurements that leaky alternatives would corrupt. Business impact: system-level ESD failures found in the field cost orders of magnitude more than a six-pin diode array - one device protects four lines, and the industrial temperature range covers both consumer and harsh-environment builds. Selection advice: the DRLR suffix is the SOT-5X3 tape-and-reel packing - for SC70 consider the DCKR variant; the 5.5V reverse standoff suits 5V-tolerant lines - for lower-voltage rails check the clamping voltage against the downstream IC absolute maximums. Featured on hqbuy.com hot search (2026-10-12). Parameters verified against Texas Instruments documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

2N7002,235 is Nexperia’s SOT-23 (TO-236AB) version of the classic 2N7002 N-channel MOSFET — 60 V / 300 mA — for small-signal switching, level shifting and load switching on space-constrained boards. The ‘,235’ suffix is Nexperia’s tape-and-reel packing code (3,000 per reel), not a different electrical part: ordering 2N7002,215 gets cut tape of the same die. Selection advice: the 5 Ω RDS(on) is high by modern standards, so keep continuous current well under the 300 mA headline rating to avoid I²R heating; for lower drop in the same footprint consider 2N7002P (1.6 Ω) or BSS138. VGS(th) is 2.5 V maximum, which 3.3 V logic can drive — but only marginally across temperature — so use a 5 V gate rail or a true logic-level part when the MCU supply is 3.3 V and the temperature range is wide. Active status through distribution; match the reel quantity to your run size before quoting. Parameters trace to the manufacturer datasheet; state quantity, packing and date-code requirements in your RFQ — we reconfirm the offered lot before quotation and reply within 24 hours.

BAT54S,215 is a Nexperia dual series Schottky diode in SOT-23, tape and reel — for ultra-high-speed switching, clamping and reverse-polarity protection in tight layouts. Two 30 V / 200 mA Schottky diodes with 5 ns reverse recovery in one SOT-23 is the selection point: series connection suits bidirectional clamping and bridge legs without a second package. Selection advice: the S denotes series — the BAT54 family also ships as BAT54 (single), BAT54A (common anode) and BAT54C (common cathode); confirm the pinout letter against your schematic before substituting, they are not interchangeable. The ,215 suffix denotes tape and reel. AEC-Q101 qualified. −65 °C to +150 °C. Nexperia lists this part as Active through distribution. Parameters verified against the Nexperia datasheet and distributor listings. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

BC847B is a Nexperia NPN general-purpose transistor — 45 V, 100 mA, gain group B (hFE 200–450), SOT-23 (TO-236AB) package, 150 °C max junction. The gain group B is the selection point: the middle gain bin of the BC847 family (A: 110–220, B: 200–450, C: 420–800) — the default choice for small-signal switching and amplification where the gain bin matters for bias stability. Selection advice: Nexperia lists the BC847B as in production. Match the gain group on the BOM — substituting a BC847C changes the bias point of a designed stage. Its PNP complement is the BC857B for complementary stages. The BC847 is the 45 V member of the family — its siblings BC848 (30 V) and BC849 (30 V, low noise) are lower-voltage, not upgrades. Evidence: Nexperia data confirms in-production, 45 V, 100 mA, gain group B, SOT-23. Match the full BC847B code — the gain letter changes the part. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

BC847C,215 is Nexperia’s highest-gain grade of the BC847 NPN general-purpose transistor — 45 V / 100 mA in SOT-23 — with DC current gain hFE 420–800 (minimum 420 at 2 mA, 5 V). The ‘C’ is the gain rank: A covers 110–220, B covers 200–450, and C covers 420–800; ‘,215’ denotes tape-and-reel packing of the same die. AEC-Q101 qualified, which makes the C grade a defensible pick for automotive-adjacent small-signal stages. Selection advice: BC847C is footprint- and pin-compatible with BC847A/B, but dropping a lower grade into a bias-sensitive amplifier stage shifts the operating point — re-check base bias when substituting grades. For pure switching the grade barely matters, and BC847B is usually cheaper and better stocked. Pair with the PNP complement BC857C for push-pull or complementary driver stages. Parameters trace to the manufacturer datasheet; state quantity, packing and date-code requirements in your RFQ — we reconfirm the offered lot before quotation and reply within 24 hours.

BCP53-16TX is a Nexperia 80V, 1A PNP medium-power transistor — for linear regulators, high-side switches and power management: SOT223 (SC-73) SMD package, 650mW total power dissipation, hFE 100 to 250 gain selection, 150C maximum junction temperature, AEC-Q101 qualified. The SOT223 package delivers 1A switching capability in a surface-mount footprint, so designs gain through-hole-class current handling without hand assembly; the -16 gain bin (100-250) suits driver stages where predictable gain matters more than maximum beta. Business impact: medium-power PNPs are the workhorse of discrete power design — linear regulator pass elements, relay drivers and load switches all standardize on this footprint, so multi-sourcing is straightforward and pricing stays competitive. Selection advice: the -16 suffix selects the 100-250 hFE bin — for wider tolerance use the base BCP53 (63-250); the TX code denotes the standard packing — for automotive PPAP flows specify the -Q variant. Ranked #5 on the hqbuy.com real-time hot list (2026-10-05). Parameters verified against Nexperia documentation. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

1N4001 is an onsemi standard rectifier diode — VRRM 50 V, 1 A average rectified current, DO-41 axial package. The 1N400x family is the selection point: the cheapest diode on earth for mains-frequency rectification and reverse-polarity protection — a jellybean part every lab stocks by the thousand. Selection advice: the 1N4001 is the 50 V bottom grade of the 1N4001–1N4007 family (50 V to 1000 V, same DO-41 package) — for mains work always specify the 1N4007 (1000 V); the 1N4001 suits low-voltage rails only. For switching supplies above a few kHz use a fast-recovery type instead — standard recovery overheats at high frequency. onsemi lists the 1N4001 as Active. Evidence: distributor data confirms onsemi 1N4001 Active, 50 V, 1 A, DO-41. Match the full 1N4001 code — siblings look identical. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.

1N4002 is a 1 A standard-recovery rectifier diode from the 1N400x family — 100 V repetitive peak reverse voltage, 1 A average forward current, 30 A surge capability, axial DO-41 (DO-204AL) package, 1.1 V maximum forward voltage, -65 to +150 °C. The 100 V rating is the selection point: the economical choice for low-voltage rectifiers, relay flyback clamps and reverse-polarity protection where high blocking voltage is unnecessary. Selection advice: pick the voltage grade to match your peak reverse voltage with margin — 1N4004 (400 V) or 1N4007 (1000 V) are the higher-voltage neighbors in the same DO-41 footprint. For switching supplies use an ultrafast type like UF5408 instead, since this is a standard-recovery part. Evidence: Vishay 1N4001–1N4007 datasheet confirms 1 A, 100 V, 30 A surge, DO-41 and 1.1 V forward voltage. Match the full 1N4002 code — the digit sets the voltage rating. State quantity, packing and date-code requirements in your RFQ; we reconfirm the offered lot before quotation and reply within 24 hours.